NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 501
Station 5db PAD S-62
S-62 Station 5db PAD
General Description
This feature allows a single-line user to be affected by the 5db loss through the system on station-to-station calls. 
Operating Procedure
No manual operation is required for this software control feature.
Service Conditions 
1. STATION 5db PAD [S-62] is inserted only for intra-office, two-way, station-to-station connections. 
2. STATION 5db PAD is inserted into the...

NEAX2400 IMX Business Features and Specifications
Page 502NDA-24221, Issue 3
S-64 Serial Call - Loop Release
S-64  Serial Call - Loop Release
General Description
This feature allows an ATTENDANT CONSOLE loop key to become available after setting SERIAL CALL [S-15]. 
Operating Procedure
1. The Attendant answers an incoming Central Office call.
2. The Attendant extends the call to the desired station, and the desired station answers.
3. The Attendant presses the SC key. The loop is now available for...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 503
Split Call Forwarding S-99
S-99 Split Call Forwarding
General Description
This feature allows a station to set two different target stations for CALL FORWARDING-ALL CALLS
(FORWARD)/BUSY LINE (FORWARD-BY)/DON’T ANSWER (FORWARD-DA), depending on whether the
incoming call is from an internal station or an outside party (C.O. TIE, DID, etc.). 
Operating Procedure
1. Station A sets or is set for CALL FORWARDING-ALL CALLS/BUSY...

NEAX2400 IMX Business Features and Specifications
Page 504NDA-24221, Issue 3
S-99 Split Call Forwarding
Operating Procedure (cont’d)
To set SPLIT CALL FORWARDING using Dterm feature key:
To set Call Forwarding from an individual station (Dterm): 
1. Setting Call Forwarding for an incoming call from a station:
a.) Confirm that the PAGE* (One-touch changeover) lamp is on; if the lamp is off, turn the lamp on
by pressing the PAGE key. 
b.) Lift the handset or press the SPEAKER key; receive dial tone. 
c.)...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 505
Split Call Forwarding S-99
Operating Procedure (cont’d)
When the destination is an outside trunk, the Dterm displays:
To cancel Call Forwarding from an individual station (Dterm):
1. Cancelling Call Forwarding for an incoming call from a station: 
a.) Confirm that the PAGE (One-Touch Changeover) lamp is on; if the lamp is off, turn the lamp on
by pressing the PAGE key. 
b.) Lift the handset or press the SPEAKER key; receive...

NEAX2400 IMX Business Features and Specifications
Page 506NDA-24221, Issue 3
S-99 Split Call Forwarding
Operating Procedure (cont’d)
When the destination is an ATTENDANT CONSOLE, the Dterm displays:
When the destination is an outside trunk, the D
term displays:
2. To monitor the assigned data for station-to-station calls:
a.) Confirm that the PAGE key LED on the D
term is illuminated. (If it is not illuminated, press the
PAGE key to turn it on.)
b.) While the D
term is in the idle state (on-hook), press...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 507
Split Call Forwarding S-99
Operating Procedure (cont’d)
b.) Dial the Tenant Number (2 digits) of the originating station and the originating telephone number.
c.) Press the RELEASE key; receive service set tone.
2. Cancelling Call Forwarding for an incoming call from an outside party:
a.) Press an idle loop key and dial the FORWARD, FORWARD-BY, or FORWARD-DA access
code for an incoming call from an outside party; receive...

NEAX2400 IMX Business Features and Specifications
Page 508NDA-24221, Issue 3
S-99 Split Call Forwarding
Service Conditions (cont’d)
11. If SPLIT CALL FORWARDING is set on a station in the hunting group (STATION HUNTING -
CIRCULAR [C-7], - TERMINAL [S-9], that station is skipped in hunting. However, if the station has set
SPLIT CALL FORWARDING for station-to-station calls only, the station is hunted for incoming calls
from outside. If the station has set SPLIT CALL FORWARDING for outside calls only, the...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 509
Slumber Time - Do Not Disturb S-106
S-106  Slumber Time - Do Not Disturb
General Description
This service allows a slumber time for up to four times per day on a Station group basis. During the slumber time,
all stations in the group concerned are placed into Do Not Disturb mode, and incoming calls (Station/DID/DIT) will
be routed to the Attendant or an announcement machine.
Operating Procedure
No manual operation is required....

NEAX2400 IMX Business Features and Specifications
Page 510NDA-24221, Issue 3
S-106 Slumber Time - Do Not Disturb
Service Conditions (cont’d)
STATION HUNTING [S-7, 9]
UNIFORM CALL DISTRIBUTION [U-1]
17. CALL BACK [C-1] and CALL WAITING-ORIGINATING [C-31] can be set from a Slumber Time
station.
18. Each of the following services is restricted to a Slumber Time station:
CALL WAITING-ORIGINATING [C-31] 
CALL BACK [C-1] 
EXECUTIVE RIGHT-OF-WAY [E-1] 
19. Each of the following terminals can access to a Slumber...