NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 541
Uniform Call Distribution (UCD) U-1
Service Conditions (cont’d)
b.) When stations belonging to different nodes are assigned to a UCD group, the station hunt is not
activated in assigned order if the stations are not assigned in continuous order within a node.
First, the call is shifted to the stations within the node of the UCD controlling station, even though
it is not in consecutive order (in the node, station hunt is...

NEAX2400 IMX Business Features and Specifications
Page 542NDA-24221, Issue 3
U-1 Uniform Call Distribution (UCD)
Service Conditions (cont’d)
c.) When the CCIS line is used as the alternative routing, SERVICE DISPLAY is not activated and
the hunting function is completed at the terminated station.
48. When using a Phantom Telephone Number (PHTELN) for a UCD controlling station via FCCS, consider
the following:
a.) Whether to use the PHTELN to start the UCD hunt or not can be selected by the command
APHNN....

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 543
Uniform Call Distribution (UCD) U-1
Interactions (cont’d)
13. The DND key functions in the same manner as the BUSY OUT key for UCD calls. However, while the
BUSY OUT key allows non-controlling UCD stations to receive calls dialed directly, use of the DND key
restricts all incoming calls.
14. If OVERFLOW-UCD [O-13] is in service, overflow will take place if all the stations in the first group are
busy or in the Busy Out state....

NEAX2400 IMX Business Features and Specifications
Page 544NDA-24221, Issue 3
U-3 Universal Sender
U-3 Universal Sender
General Description
This feature permits dialed numbers to be transmitted via a sender, a device that will automatically add or delete the
necessary number of digits or perform any necessary conversions.
Operating Procedure
No manual operation is required.
Service Conditions
1. For incoming connections, digits may be deleted according to the route involved. A maximum of 4 digits
may be...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 545
Variable Timing Parameters V-1
V-1 Variable Timing Parameters
General Description
The Variable Timing Parameters feature gives the PBX the versatility to change timing parameters, using the
MAINTENANCE ADMINISTRATION TERMINAL (MAT) [M-18]. All timing parameters for a specific timing
sequence are set initially within the generic program. These timing parameters can be changed to accommodate user
requirements. 
Operating...

NEAX2400 IMX Business Features and Specifications
Page 546NDA-24221, Issue 3
V-1 Variable Timing Parameters
Interactions
1. To calculate VARIABLE TIMING PARAMETERS, multiply the Timer Class by the Miscellaneous
Timer Class, TC x MTC = VARIABLE TIMING PARAMETER. TC is a set value. MTC is any value
from 1-15, assigned in hexadecimal. For the PERIODIC TIME INDICATION TONE Timer, a TC of 3
equaling 2 seconds is not available, but a TC of 4 equaling 30 seconds is available.
Timer Index:
TC values for Indexes...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 547
Variable Timing Parameters V-1
Interactions (cont’d)
TC values for Indexes 142, 143, 144 
TC 0 = -
1 = -
2 = -
3 = 2 seconds
4 = 30 seconds 
7 = 8 seconds.
TC values for Indexes 135 
TC 0 = -
1 = 64 msec.
TC values for Indexes 149 
TC 0 = -
1 = -
2 = -
3 = 2 seconds
4 = 30 seconds. 
TC values for Indexes 145 
TC 0 = -
1 = 2 seconds. 

NEAX2400 IMX Business Features and Specifications
Page 548NDA-24221, Issue 3
V-2 Voice Call
V-2 Voice Call
General Description
This feature enables a single line telephone to make a VOICE CALL [V-2] when the called party is a Dterm set. This
path exists from the calling party to the called partys built-in speaker. If the called partys MIC is on, the called party
can converse hands-free.
Operating Procedure
From a single line station to a Dterm:
1. Dial the telephone number of the desired Dterm station...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 549
Voice Call - DtermV-2D
V-2D Voice Call - Dterm
General Description
This feature provides a voice path between two Dterm sets. This path exits from the calling party to the called party’s
built-in speaker. If the called party’s MIC key is on, the called party can converse hands-free. 
Operating Procedure
From one Dterm to another Dterm:
1. The originating Dterm user dials the desired telephone number and receives a ringback...

NEAX2400 IMX Business Features and Specifications
Page 550NDA-24221, Issue 3
V-3D Volume Control - Dterm
V-3D Volume Control - Dterm
General Description
This feature is used for controlling the volume of a Dterm set’s built-in speaker and receiver.
Operating Procedure
1. The Dterm set is equipped with a sliding volume control knob located in the front, beneath the dial pad.
Volume can be increased by moving the control to the right, and decreased by moving it to the left.
2. The ringing volume is...