NEC Neax 1000 Ivs Very Small Platform System Manual

 NDA-24219   CHAPTER 3
NAP-2 00-003
PZ-PW86 (C)
PW R CNT C A-A/
FRAME G ROUND TERMINAL  ON THE CHASSIS
C A UTION :Set the app ropri ate  voltage be fo re
Note 1 :Follow the Labe l on the f ront plate of the PZ-PW86.
B ATTE RY CONNEC TO R  (B ATT1)
1Note 1
1 :NO CONNECTI ON 

CHAPTER 3 NDA-24219  
Page 38
Revision 2.0
NAP-200-003
Sheet 9/12
Installation of Main Equipment
Figure 003-7 Cable Connection on PZ-PW86/PW112 (Continued)
PZ-PW86(D)
MJ
MN
ON
BATTERY MODE SWITCH
GND  
Note 2
FG
–27V
PWR CNT CA-A/ TO PWR1
AC CORD-A
TO AC MAINS INPUT TO TO PWR0A CONNECTOR POWER OUTPUT
CONNECTOR TO AUXILIARY 
BATTERY CONNECTOR (BATT2)
ON
OFF 100/120V
240V EQUIPMENT
GREEN WHITE
BLACK
FRAME GROUND
Note 1: Follow the Label on Front Plate of
PZ-PW86(D).
Note 2: If GND (Signal GND) has to be...

 NDA-24219 CHAPTER 3
Page 39
Revision 2.0
NAP-200-003
Sheet 10/12
Installation of Main Equipment
Figure 003-7 Cable Connection on PZ-PW86/PW112 (Continued)
PZ-PW112
MJ
MN
ON
GND  
Note
FG
–27V
PWR CNT CA-A/ TO PWR1
AC CORD-A
TO AC MAINS INPUT TO  CONNECTOR TO AUXILIARY 
BATTERY CONNECTOR (BATT2)
ON
OFF EQUIPMENT
GREEN WHITE
BLACK
FRAME GROUND
Note: If GND (Signal GND) has to be
separated from FG (Frame GND),
remove the link between GND and
FG terminal
–
O
TERMINAL ON THE  TO OTHER PZ-PW112
PWR CA-A
TO...

CHAPTER 3  NDA-24219    
NAP-200-003
LTC CONNECTOR AREA
PI M1
PWR0C
PWR C NT CA -C
LTC CON NECTOR AREA
PIM0
PWR0C
P WR  CNT CA-C 

 NDA-24219 CHAPTER 3
Page 41
Revision 2.0
NAP-200-003
Sheet 12/12
Installation of Main Equipment
(3) Bring the AC CORD-A-U out of the PIM through the cable hole on the bottom of the lower PIM, and plug
it into a commercial AC outlet.
Figure 003-9  AC Power Cable Wiring
AC CORD-A-U
TO FGTERMINAL 

CHAPTER 3  NDA-24219    
NAP-200-004
PIM1
Note :
For details of battery connectio n, see NAP- 200-00 4.
P WR C A-A
PIM1
P WR C A-A
TO B ATT ER Y
TO B ATT ER Y 

 NDA-24219 CHAPTER 3
Page 43
Revision 2.0
NAP-200-004
Sheet 2/2
PWR CA-A and BUS Cable Connection
(2) Mount the BS00 Card in the BUS slot of PIM0. Also, mount the BS01 Card in the BUS slot of PIM1.
When the system is a single PIM configuration, neither PN-BS00 nor PN-BS01 is needed.
(3) Connect the BUS cards using BUS cable (48-TW-0.7 CONN CA).
Figure 004-2  Mounting BUS Cards
PIM1
PIM0BS01
CN2
CN1
BS00
CN2
CN1
48-TW-0.7
CONN CA 

CHAPTER 3 NDA-24219  
Page 44
Revision 2.0
NAP-200-005
Sheet 1/4
Connection of Battery
1. BATTERY CONNECTION
CAUTION 1:24V batteries must be used in this system.
CAUTION 2:If battery terminals (+, –) contact with the module under connecting the battery cable to the PZ-
PW86/PW112 card, the PZ-PW86/PW112 card or the BWB may be broken. Therefore, the in-
staller must perform work in accordance with the following steps when mounting or removing
the batteries.
• When mounting batteries:
(1) Connect the...

 NDA-24219 CHAPTER 3
Page 45
Revision 2.0
NAP-200-005
Sheet 2/4
Connection of Battery
CAUTION 3:
Battery Replacement Table and Battery Warnings
The label, which shows battery replacement table and battery warnings, is attached to the re-
verse side of Front Cover for PIM. During the battery installation process, always observe the
warning statements. When replacing batteries, adhere to the battery replacement table to in-
crease battery life and to insure safe operation. See Figure 005-1.
Figure 005-1...

CHAPTER 3 NDA-24219  
Page 46
Revision 2.0
NAP-200-005
Sheet 3/4
Connection of Battery
1.1 Internal Battery Connection
(1) Mount the battery unit (24V DC, 2.6 AH) into the PIM (standard with system) as shown in Figure 005-2.
Figure 005-2  Internal Battery Mounting
FRONT 34mmDIMENSION OF BATTERY BATTERY UNIT
(2´
12V DC, 2.6 AH)
(STANDARD)
(1.3 inches)
178mm
(7 inches) 60mm
(2.4 inches)
PIM
Red
Blue Black
+–+
–