NEC Neax 1000 Ivs Very Small Platform System Manual

  NDA-24219 REGULATORY INFORMATION
Page ix
Revision 2.0
(b) This equipment returns answer supervision on all DID calls forwarded to the PSTN. Permissible ex-
ceptions are:
• A call is unanswered
• A busy tone is received
• A reorder tone is received.
EQUAL ACCESS REQUIREMENTS
This equipment is capable of providing users access to interstate providers of operator services through the use of
access codes. Modification of this equipment by call aggregators to block access dialing codes is a violation of...

REGULATORY INFORMATION NDA-24219  
Page x
Revision 2.0
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the
supplier. Any repairs or installations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request that the user disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone
lines, and internal metallic...

  NDA-24219 REGULATORY INFORMATION
Page xi
Revision 2.0
(10) Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by plac-
ing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or
over a radiator or heat register. This product should not be placed in a built-in installation unless proper
ventilation is...

REGULATORY INFORMATION NDA-24219  
Page xii
Revision 2.0
This page is for your notes. 

 NDA-24219 CHAPTER 1
Page 1
Revision 2.0
CHAPTER 1 INTRODUCTION
1. PURPOSE
This manual explains the installation procedure for the NEAX1000 IVS (PBX) System.
2. REFERENCE MANUAL
During installation, refer to the NEAX2000 IVS manuals listed in Figure 1-1.
Figure 1-1   Installation Reference Manuals
CIRCUIT CARD MANUALCOMMAND DESCRIPTION MAINTENANCE PROCEDURE
MAINTENANCE MANUAL REFERENCE MANUALS
COMMAND MANUAL
CIRCUIT CARD DESCRIPTION
CIRCUIT CARD MOUNTING CONDITIONS
SWITCH SETTING OF CIRCUIT CARD...

CHAPTER 1 NDA-24219 
Page 2
Revision 2.0
3. HOW TO FOLLOW THIS MANUAL
The Installation Procedure is shown by means of flowcharts with an NAP (NEC Action Procedure) Number. The
detail of the work for each step is described in corresponding NAP.
4. SCOPE OF INSTALLATION PROCEDURES
This manual covers the installation shown in Figure 1-2.
Figure 1-2   Scope of Installation Procedures
MDF
MDF CABLESN610
ATTCON
Multiline Terminal
NAP-200-003:
INSTALLATION OF MAIN EQUIPMENT
NAP-200-007:
SWITCH SETTING OF...

 NDA-24219 CHAPTER 2
Page 3
Revision 2.0
CHAPTER 2 GENERAL INFORMATION
1. TRUNKING DIAGRAM
Figure 2-1 shows a typical trunking diagram for the PBX.
Figure 2-1   PBX Trunking Diagram
MODEM
Note 3:An external Modem is not required when the Built-In Modem on the MP is used.
Note 4:NEAX1000 may also be used as a Remote PIM.
Note 5:Customer provides equipment marked with (*).
4W E&M
2W E&M
RS 232C
V. 1 1
TCP/IP
V. 1 1
RS-232C
RS 232C
VOICE MAIL
SYSTEM
Multiline Terminal
DSS
Multiline Terminal
Long Line DSS...

CHAPTER 2 NDA-24219  
Page 4
Revision 2.0
Note:Refer to NAP-200-008 and the Circuit Card Manual for details of circuit cards.Table 2-1  Symbols in Trunking Diagram Description
SYMBOL DESCRIPTION
SYMBOL DESCRIPTION
AMP Amplifier for External Speaker
ILCA BRI Station Line Card
AP00 SMDR/MCI/PMS/Hotel Application Card KEY External Key
AP01 OAI Interface Card LCD/LCS Line Circuit Card
(for Single Line Telephone)
AUC Analog Universal Circuit Card
(Long Line Circuit, DID Trunk)MAT Maintenance Administration...

 NDA-24219 CHAPTER 2
Page 5
Revision 2.0
2. SYSTEM CONFIGURATIONS
2.1 PIM Configuration
The PBX system can accommodate a maximum of 48 ports per PIM. A maximum of 88 ports are available with a
two PIM configuration (PIM0 Slot LT08/AP4 used for PN-BS00). 
Figure 2-2   PIM Configuration
TWO PIM CONFIGURATION ONE PIM CONFIGURATION 

CHAPTER 2 NDA-24219  
Page 6
Revision 2.0
2.2 Installation Methods
Figure 2-3   Wall-Mounting Installation
PIM