NEC Ds2000 Software Instructions Manual

Station Message Detail Recording
DS1000/2000 Software ManualChapter 1: Features353
Programming List
Program 0301 - CPU Baud Rate (page 450)
Assign the baud rate for the RS-232-C port on the CPU. The options are as follows
Fix
ed Slot and U Slot prior to 02.00.01:
- 1 (1200)
- 2 (2400)
- 3 (4800)
- 4 (9600)
- 5 (19200)
U Slot 02.00.01 and higher and DS1000:
- 1 (2400)
- 2 (4800)
- 3 (9600)
- 4 (19200)
- 5 (38400)
- 6 (57600) - DS1000 Only
- 7 (115000) - DS1000 Only
You can also use Ctrl + Break from a...

System Diagnostics
354Chapter 1: FeaturesDS1000/2000 Software Manual
System Diagnostics
Description
To check your system’s software version:
1. Do not lift the handset, do not press 
SPK, and do not press ICM.
2. Dial 8.
Your system’s software version displays. DS2000 Fixed Slot
See steps below. DS2000 U Slot
DS1000 

System Identification
DS1000/2000 Software ManualChapter 1: Features355
System Identification
Description
The system adminstrator can enter the site name and telephone number into the system data base. 
This information is saved into system memory and will appear on system diagnostic reports, once 
available.
Conditions
None
Default Setting
No entries.
Programming Guide
DS2000 Fixed Slot
Available. DS2000 U Slot
DS1000
Store the site name and telephone number in the system data base.
Step-by-step guide...

System Identification
356Chapter 1: FeaturesDS1000/2000 Software Manual
Programming List
Program 0302 - Company Name (page 452)
14 Enter the name of the company (up to 14 characters) at which the system is installed. The 
name appears on top of various system reports.
Program 0302 - Company Phone Number (page 452)
Enter the number that the system should call to report a fault. This is not the number of the 
company where the system is installed. It is the number of the remote service center.
Other...

System Programming Backup and Restore
DS1000/2000 Software ManualChapter 1: Features357
System Programming Backup and Restore
Description
The PC Card provides a permanent, non-volatile backup of all the site’s programming. If you have 
backed up your site data to a PC Card, for example, you can easily restore all site programming 
after an extended power failure.
Versions 02.00.01 and Higher
Use PC Card P/N 85880 to back up and restore your site data. Each PC card can store up to 16 com-
plete data...

System Programming Backup and Restore
358Chapter 1: FeaturesDS1000/2000 Software Manual
Conditions
See Compatiblity Guidelines above.
Default Setting
No data bases stored.
Programming Guide
Step-by-step guide for setting up System 
Programming Backup and Restore 
Step 1: Do you want to back up the site data to a PC Card?
• In Program 9906 - Database Save (page 567), 
back up the site data to one of the 12 available PC 
card addresses.
• Refer to the system Hardware Manual for addi-
tional information on...

System Programming Backup and Restore
DS1000/2000 Software ManualChapter 1: Features359
Programming List
Program 9906 - Database Save (page 567)
Save (back up) site data to a PC card.
Program 9907 - Database Load (page 569)
Restore (load) site data from a PC card.
Program 9908 - PC Card Erase Utility (page 570)
Erase all the data bases in Data Base PC Card P/N 85880.
Other Related Features
System Diagnostics (page 354)
If the system diagnostics report a critical fault that requires a CPU change or...

System Programming List
360Chapter 1: FeaturesDS1000/2000 Software Manual
System Programming List
Description
The following system programs are available:
Program 0100 - Class of Service (page 440)
Program 0101 - Class of Service Options (page 440)
Program 0200 - Tenant Options (page 445)
Program 0201 - Tenant Option Programming (page 445)
Program 0300 - System Options (page 449)
Program 0301 - System Options (Part 1) (page 449)
Program 0302 - System Identification (page 452)
Program 0400 - Timers (page...

System Programming List
DS1000/2000 Software ManualChapter 1: Features361
Program 1702 - Personal Speed Dial (page 522)
Program 1703 - DSS Key Assignment (page 524)
Program 1704 - DSS Console Key Assignment (page 526)
Program 1800 - Extension Options (page 532)
Program 1801 - Extension Port Description (page 532)
Program 1802 - Extension Options (Part 1) (page 539)
Program 1803 - Extension Line Access Assignments (page 546)
Program 1804 - Extension Trunk Group Access (page 549)
Program 1805 - Ring...

System Programming Password Protection
362Chapter 1: FeaturesDS1000/2000 Software Manual
System Programming Password Protection
Description
The system controls access to the programmable options according to the programming password 
the administrator enters. There are three password levels:
Conditions
None
Default Setting
See the table above.
Programming List
Program 9905 - Password (page 566)
Review the complete list of programmable options. DS2000 Fixed Slot
Available. DS2000 U Slot
DS1000
Control...