Namco Mazan Operators Manual

Page 61
TEST FAILED 1
SENSOR 1 : O.K.
SENSOR 2 : ERROR 4
PUSH THE START BUTTON
FOR 10 SECONDS TO EXIT
(a)
(b)
t l u s e Rno i t i d n o C
G N I N R A Wn o i t i d n o c  R O R R E  n i s i 2 R O S N E S r o 1 R O S N E S f o e n o t s a e l t A
1 D E L I A F T S E Td n a , n o i t i d n o c  ! R O R R E  n i r o  K O  s i 2 R O S N E S r o 1 R O S N E S r e h t i E
, r o r r e r e h t o n a s a h r o s n e s r e h t o e h t
2 D E L I A F T S E T.e v o b a d e b i r c s e d e s o h t n a h t r e h t o n o...

Page 62
7. MAINTENANCE
  
Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
Ensure that the 
POWER to the machine is turned OFF before commencing
any maintenance work. (Trouble shooting, service or repairs etc.)
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem
Fachpersonal vorgenommen werden.
Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der
Netzstecker gezogen werden.

 

 


Justeringer eller...

Page 63
  
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te
worden door bekwaam personeel.
Zorg ervoor dat de machine UITgeschakeld is voordat er enig
onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)
  
Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente
por pessoal qualificado.
Certifique-se que a maquina se encontra desligada sempre que iniciar
qualquer tipo de trabalho de manutenção. (identifação de avarias,
reparação etc.)...

Page 64 7-1 Cleaning
7-1-1 Cleaning the Reflective Strip
•Do not use organic solvents such as thinners.
•Do not use alkali or acid cleaning agents.
1. Use a soft cloth dampened with a diluted neutral detergent.
2. Use a clean dry soft cloth to wipe any detergent or water from the surface.
7-1-2 Cleaning the panel glass
•Do not use organic solvents such as thinners.
1. Using a glass cleaner, wipe the inside and outside surfaces with a soft cloth.
2. Use a clean dry soft cloth to wipe any detergent or...

Page 65
7-1-3 Cleaning the Screen Guard
•Do not use organic solvents such as thinners.
•Do not use alkali or acid cleaning agents.
1. Use a soft cloth dampened with a diluted neutral detergent.
2. Use a clean dry soft cloth to wipe any detergent or water from the surface.
7-1-4 Repairing the Reflective Strip If the reflective strip inside the Frame Assembly is peeling or scratched, the
sensors cannot detect the sword position correctly. To repair the damage, cut a
piece from the provided reflective...

Page 66 7-2 Removing the Front Panel
1. Remove 4off security screws (M5x12).
2. Undo the lock and tilt the Front Panel forward to remove.
3. Reassemble in reverse order.
Front panel
Projector base
Torque bolt (M5 x 12)
Security screw (M5 x 12)
Projector base Front panel
Unlock 

Page 67
7-3 Removing the Control Base Assy
1.  Remove the Front Panel. (see 7-2 page 66)
2. Disconnect the five connectors.
3. Remove 2off pozi head screws (M5x25), with flat and spring washers.
4. Remove the Control Base Assy by lifting straight up.
5. Reassemble in reverse order.
Connectors Control Base Assy
Pozi head screw (M5 x 25)
(with flat and spring washers)
Control Base Assy 

Page 68
7-4 Replacing the NAOMI PCB Assy
1.  Remove the Front Panel. (see 7-2 page 66)
2.  Remove the Control Base assy. (see 7-3 page 67)
3. Disconnect the four connectors.
4. Remove the 4off pozi head screws (M5x12).
5. Remove the NAOMI PCB Assy.
6. Reassemble in reverse order.
Control Base Assy
Connectors
Pozi head screw (M5 x 12)
Control Base Assy 

Page 69
7-5 Replacing the Screen Guard
1.  Seperate the Monitor Base Assy from the Front Assy. (see 5-2 page 35)
2.  Remove the Signboard Assy. (see 5-3 page 36)
3.  Remove the Front Panel. (see 7-2 page 66)
4. Remove 2off security screw (M5x25) and 4off pozi head screws (M5x16), and remove the Monitor Mask.
5. Remove 18off Whizz nuts, and remove the two pairs of Guard Brackets (A),(B), and remove the screen guard.
6. Reassemble in reverse order.
Note: The front and rear sides of the Screen Guard are...

Page 70 7-6 Removing the Control Panel
1. Remove 4off security screw (M5x12).
2. Disconnect the connector and remove the Control Panel.
(There is no connector to disconnect on the left hand Control Panel).
3. Reassemble in reverse order.
Control panel (R)
Connectors
Security screw (M5 x 12)