Namco Mazan Operators Manual

Page 51
6-2-3-2 Sensor Level Check
This item is used to check the sensitivity of the four sensor assemblies\
.
Ensure that the sensors are adjusted so that the results indicate “OK” for all four
sensors. (see 5-5-3 page 40 for sensor adjustment)
1. Select “SENSOR LEVEL CHECK” from the I/OTEST menu. The following screen is displayed
Note: The two sensors nearest the projector, view from the front, are indicated as “SENSOR 1”, and the two sensors nearest the player are indicate\
d as
“SENSOR 2”.
I / O...

Page 52
6-2-3-3 Sword Test
This item checks the sword movement within the sense area.
1. Select “SWORD TEST” from the I/O menu screen. The following screen is displayed.
2. The screen will display the sword when the sword is placed in the sensor\
 area. Check that the sword is displayed in the relevant position.
* If “NOT WORKING” is displayed against either sensor, that numbersensor on either the left or right is malfunctioning. If this happens, t\
he
angle of the sword displayed on the screen will be...

Page 53
6-2-3-4 Sword Adjustment
This item checks the sword alignment.
This check should only be performed when the sword position is found to \
be
incorrect during the “SWORD TEST” (see 6-2-3-3 page 52) and no problem is
detected in the “SENSOR LEVEL  CHECK”. (see 6-2-3-2 page 51)
1. Select “SWORD ADJUSTMENT” from the I/O menu screen. The following screen is displayed.
2. Place the blade of the sword inside the sensor area, in line with the ye\
llow square displayed on the screen.
* Be sure to hold the...

Page 54
•If the adjustment procedures could not be completed correctly, select “RETRY”
and press the Enter switch. Then, repeat the sword alignment adjustment from
the beginning.
•When the adjustment procedures have been completed successfully, select
“SAVE & EXIT” and press the Enter button. The settings are saved, and the
display returns to the I/O Test menu screen.
•To keep the original settings without saving the settings just made, sele\
ct “EXIT”
and press the Enter switch. The display returns to...

Page 55 6-2-3-5 Switch Test
This item checks the operation of the game switches.
1. Select “SWITCH TEST” from the I/O menu screen. The following screen is
displayed.
(a) The counter will increment each time a credit signal is received from
the coin mech.
(b) ~ (f) The display will change from OFF to ON each time the corresponding
switch is operated.
(g) ~ (h) The display will change from OFF to ON each time the sword is placed
within the sensor area.
(i) This item is not used on this game.
2. Press the...

Page 56 6-2-3-6 Lamp Test
This item checks the operation of the Start button lamp.
1. Select “LAMP TEST” from the I/O menu screen. The following screen is
displayed.
2. As soon as this screen is displayed, the Start button lamp will be lit. After a
short period the ON message will change to OFF and the Start button lamp
will turn off. The lamp will also turn off when exiting from the LAMP TEST
Screen.
3. Select “EXIT” and press the Enter button to return to the I/O TEST Menu
screen.
 START BUTTON  LAMP...

Page 57 6-2-4 Monitor Test
1. Select “MONITOR TEST” on the menu screen to test and adjust the Monitor. The
following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter
button. To return to the Monitor Test Menu from a test pattern press the Enter
button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
(a) Displays a colour gradation pattern.
(b) Displays a crosshatch pattern for a CRT monitor. (Not used on this game)
(c)...

Page 58 6-2-5 Sound Test
1. Select “SOUND TEST” on the menu screen to test the audio and adjust the
volume settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter
button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button to return to item select mode
5. Select “EXIT” and press the Enter button to return to the menu screen.
(a) GAME
This sets the volume level of the sound during the Game Mode.
[0 ~127, DEFAULT...

Page 59
6-2-6 ADS Data (Bookkeeping)
1. Select “ADS DATA” from the menu screen to view the bookkeeping details.
2. Select “EXIT” and press the enter switch to return to the menu scr\
een.
6-2-7 Others 1. Select “OTHERS” on the menu screen to display the ROM version, to \
set the on screen language, display mode and to set all settings to factory default\
.
2. Use the Select Up/Down switch to choose the required item then press the\
 Enter button.
3. Select “EXIT” and press the Enter button to return to...

Page 60 6-3 Self Test
This machine performs a self-test routine (self-test and sensor initialization)
automatically each time the power switch is turned on, or exiting the SENSOR LEVEL
CHECK screen in the test mode. When the game is functioning correctly, the following
screen is displayed after a short period of time. If there is an error, an error message
(“WARNING”, “TEST FAILED”, etc) is displayed on the monitor, and the game stops
operation. Rectify the problem according to the individual test...