Motorola Mc9500k Manual

							Accessories 8 - 11
Four Slot Battery Charger
This section describes how to use the Four Slot Battery Charger.
The Four Slot Battery Charger:
Simultaneously charges up to four MC9500-K batteries.
Mounts on a wall or desk using the appropriate mounting bracket.
Battery Charging
To charge a battery:
1.Ensure that the charger is connected to power.
2.Insert a battery into a battery charging slot and gently press the battery into the slot to ensure proper contact.
Figure 8-8    Four Slot Battery Charger
The charging status is indicated on the front of the battery. See Table 2-7 on page 2-8 for charging status 
indications. The 4800 mAh battery fully charges in less than six hours.
Battery 
						

							8 - 12 MC9500-K Mobile Computer User Guide
Vehicle Cradle
This section describes how to use a vehicle cradle with the MC9500-K. For cradle installation and communication 
setup procedures refer to the VCD9500 Vehicle Cradle Quick Reference Guide.
Once installed in a vehicle, the cradle:
holds the MC9500-K securely in place
provides power for operating the MC9500-K
re-charges the battery in the MC9500-K.
Charging the MC9500-K Battery
Insert the MC9500-K into the vehicle cradle with the display facing out.
Push back the level forward to lock the MC9500-K into place. The MC9500-K automatically begins charging.
Figure 8-9    Vehicle Cradle
To remove the MC9500-K, push the side levers toward the back of the Vehicle cradle. Lift the MC9500-K out of the 
cradle.
The MC9500-K’s Battery Status LED indicates the status of the battery charging in the MC9500-K. See Table 1-1 
on page 1-7 for charging status indications. The 4800 mAh battery fully charges in less than six hours.
NOTEThe MC9500-K will not begin charging unless the side level is locked into place.
Side Lever
CAUTIONEnsure the MC9500-K is fully inserted in the cradle. Lack of proper insertion may result in property damage 
or personal injury. Motorola is not responsible for any loss resulting from the use of the products while 
driving.  
						

							Accessories 8 - 13
Vehicle Battery Charger
This section describes how to use the Vehicle Battery Charger.
Charging the Battery
To charge a spare battery:
1.Ensure that the charger is connected to power.
2.Insert the spare battery into the slot to begin charging.
Figure 8-10    Vehicle Battery Charger
The charging status is indicated on the front of the battery. See Table 2-7 on page 2-8 for charging status 
indications. The 4800 mAh battery fully charges in less than six hours.
To remove the battery, press the release button. The battery ejects from the charger.
Release Button 
						

							8 - 14 MC9500-K Mobile Computer User Guide
Magnetic Stripe Reader
This section describes how to set up and use the snap-on (Magnetic Stripe Reader (MSR) with the MC9500-K. The 
MSR snaps on to the back of the MC9500-K and removes easily when not in use.
When attached to the MC9500-K, the MSR allows the MC9500-K to capture data from magnetic stripe cards. To 
download sample MSR data capture software, visit the Support Central web site.
To charge to MC9500-K with the MSR attached, 
Attaching and Removing the MSR
To attach, slide the cleat of the MSR into the interface pocket of the MC9500-K and snap into place.
Figure 8-11    MSR Installation
To remove the MSR, press the release button and lift off the MC9500-K.
Using the MSR
Install an MSR enabled application onto the MC9500-K.
To use the MSR:
1.Attach the MSR to the MC9500-K.
2.Power on the MC9500-K.
3.Launch the MSR application.
NOTEWhile the MC9500-K with MSR is attached to ta Single Bay USB Cradle, a Four Bay Ethernet Cradle or a 
USB/Charging Cable, Operation of the MSR is disabled.
If attaching the MC9500-K with the MSR onto a Four Bay Cradle, remove the optional guide cup before 
attaching the MC9500-K.
Release Button 
						

							Accessories 8 - 15
4.Swipe the magnetic stripe card through the MSR, with the magnetic stripe on the card facing away from the 
MC9500-K. Swipe the card in either direction, up and down or down and up. For best results, gently press the 
card against the back of the MSR while swiping to ensure contact with the reader.
Figure 8-12    Swipe Card through MSR
5.The application indicates if the data has been read correctly. 
						

							8 - 16 MC9500-K Mobile Computer User Guide
Cables
This section describes how to set up and use the cables. The cables are available with a variety of connection 
capabilities.
The following communication/charge cables are available:
USB/Charge cable
Provide the MC9500-K with operating and charging power when used with the Motorola approved power 
supply.
Synchronize information between the MC9500-K and a host computer. With customized or third party 
software, it can also synchronize the MC9500-K with corporate databases.
Figure 8-13    USB/Charge Cable
Charge Only cable
Provide the MC9500-K with operating and charging power when used with the Motorola approved power 
supply.
Single Bay Cradle/Charger Y Cable
Provide the power to a Single Bay USB Cradle and Single Slot Battery Charger or two Single Slot Battery 
Chargers off one power supply when used with the Motorola approved power supply.
Figure 8-14    Single Slot Cradle/Charger Y-Cable
Auto Charge cable.
Provides the MC9500-K or Vehicle Battery Charger with operating and charging power tough a cigarette 
lighter. 
						

							Accessories 8 - 17
Figure 8-15    Auto Charge Cable
Figure 8-16    Cable Installation
Battery Charging and Operating Power
The communication/charge cables can charge the MC9500-K battery and supply operating power.
To charge the MC9500-K battery:
1.Connect the cable power input connector to the Motorola approved power source.
2.Align the cleat on the cable with the interface pocket on the back of the MC9500-K.
The MC9500-K amber Battery Status LED indicates the MC9500-K battery charging status. The 4800 mAh 
battery charges in less than six hours. See Table 1-1 on page 1-7 for charging status indications. 
3.When charging is complete, press the release button up and remove the cable from the MC9500-K.
Vehicle Adapter Module
Release Button 
						

							8 - 18 MC9500-K Mobile Computer User Guide 
						

							Chapter 9 Maintenance & Troubleshooting
Introduction
This chapter includes instructions on cleaning and storing the MC9500-K, and provides troubleshooting solutions 
for potential problems during MC9500-K operation.
Maintaining the MC9500-K
For trouble-free service, observe the following tips when using the MC9500-K:
Do not scratch the screen of the MC9500-K. When working with the MC9500-K, use the supplied stylus or 
plastic-tipped pens intended for use with a touch-sensitive screen. Never use an actual pen or pencil or other 
sharp object on the surface of the MC9500-K screen. 
Motorola recommends using a screen protector, p/n KT-122010-01R.
The touch-sensitive screen of the MC9500-K is polycarbonate. Do not to drop the MC9500-K or subject it to 
strong impact.
Protect the MC9500-K from temperature extremes. Do not leave it on the dashboard of a car on a hot day, 
and keep it away from heat sources.
Do not store the MC9500-K in any location that is dusty, damp or wet.
Use a soft lens cloth to clean the MC9500-K. If the surface of the MC9500-K screen becomes soiled, clean it 
with a soft cloth moistened with a diluted window-cleaning solution.
Periodically replace the rechargeable battery to ensure maximum battery life and product performance. 
Battery life depends on individual usage patterns. The battery provides health status to assist in determining 
useful battery life. See Chapter 2, Battery Management for more information.
Do not scratch the exit window. Clean the window periodically. Dust, contamination, and scratches on the exit 
window can cause visible blemishes in the images captured with the Imager. 
						

							9 - 2 MC9500-K Mobile Computer User Guide
A screen protector is applied to the MC9500-K. Motorola recommends using this to minimize wear and tear. 
Screen protectors enhance the usability and durability of touch screen displays. Benefits include:
Protection from scratches and gouges
Durable writing and touch surface with tactile feel
Abrasion and chemical resistance
Glare reduction
Keeping the device’s screen looking new
Quick and easy installation.
Removing the Screen Protector
A screen protector is applied to the MC9500-K. Motorola recommends using this to minimize wear and tear. 
Screen protectors enhance the usability and durability of touch screen displays.
To remove the screen protector, lift the corner using a thin plastic card, such as a credit card, then carefully lift it off 
the display.
Figure 9-1    Removing the Screen Protector
Battery Safety Guidelines
The area in which the units are charged should be clear of debris and combustible materials or chemicals. 
Particular care should be taken where the device is charged in a non commercial environment.
Follow battery usage, storage, and charging guidelines found in the users guide.
Improper battery use may result in a fire, explosion, or other hazard.
Lift Screen
Protector
Corner
CAUTIONDo not use a sharp object to remove the protector. Doing so can damage the display.
NOTENot using a screen protector can affect warranty coverage. To purchase replacement protectors, contact your 
local account manager or Motorola, Inc. These include screen protector installation instructions. Part number: 
KT-122010-01R Screen Protector 3/pk.