Mitel Voice Processing Solutions Instructions Manual

VoiceMemo Release 6.OA and later 
Task Procedure 
reating ware Types 
Assign a Default Hardware Type ......................................................... CP 5732 
Modify a Hardware Type.. ....................................................................... Cl? 5733 
Create and Configure a New Hardware Type.. ......................................... Cl? 5734 
Create and Configure MESA-Net Links .............................................. Cl? 5712 
Change the Answer or Originate Link Assignment...

Configure Parallel Links 
Page 1 of 1 
VoiceMemo Release 6.OA and later 
This procedure describes how to configure parallel links on the Centigram server that 
originates the MESA-Net sessions between two nodes. With parallel links enabled, 
MESA-Net establishes a new connection each time the current connection or 
connections have been open for a set number of minutes. The answering node also must 
have the parallel links optional feature installed and have enough answer links to carry all 
of the...

Configure MESA-Net Async Links 
Page 1 of 4 
VoiceMemo Release 6.OA and later 
This procedure describes how to create MESA-Net Async links on your Centigram 
Series 6 Communication Server and configure each link for the following parameters: 
6 Communication parameters (baud rate, parity, data bits, stop bits, flow control) 
Failure counts (determines when a communications channel has too many transmission 
errors) 
e Network hardware type (assigns a hardware type to work with the communications device)...

Cl? 5712 
Page 2 of 4 
VoiceMemo Release 6.OA and later 
8. Assign a baud rate fo: the link you have created. Thedefault is 9600. 
Select: (B) Baud rate 
1 
; 
; 
i 
1 
BAUD RATES 
64000 
57600 
38400 
19200 
9600 
4800 
2400 
1200 
300 
Step 
GD Configure the Serial Port 
5. Select I? to reach the Serial Port Device Type Menu 
6. Assign a port to the link you have created. 
Prompt: 1/2/3/X: 
Response: 
1 for ports on Serial 16/32 cards and Smartcards 
Prompt: 
Enter cti card port number (l-32):...

Cl? 5712 
Page 3 
of4 
VoiceMemo Release 6.OA and later 
Step 
9. Set the parity required for the link. The default is no parity. 
Select: (P) Parity 
Prompt: 
PARITY 
(N) None 
(0) Odd 
(E) Even 
(M) Mark 
(S) Space 
Response: The letter (IN, 0, E, M, or S) that represents the parity for the link you 
have created. 
10. Configure the data bits for the link. The default is 8. 
Select: (D) Data bits 
prompt: Number of data bits [S]: 
Response: The number of data bits (7 or 8) for the link you have...

Cl? 5712 
Page 4 of 4 
VoiceMemo Release 6.OA and later 
Step Re$rence 
@TJj onfigure the Timeout Parameters 
14. Go to the Timeout Parameters Menu. 
15. Set the timeout parameters. The default value for each of the timeout parameters is 
60 seconds. 
Prompt: R/S/I/X: 
Response: R to set the data receive timeout, 
S to set the resend timeout, 
I to set the node inactivity timeout. 
Enter the new timeout value, in seconds, when you are prompted to do so. 
16. Exit to the Network Maintenance Menu to save...

r 
elete MESA-Net Async Links 
Page 1 of 1 
VoiceMemo Release G.OA and later 
This procedure describes how to delete MESA-Net Async links. This is necessary if, for 
example, you are distributing the existing links on your Centigram Series 6 server for 
load share purposes. In that case, you would first delete the appropriate number of links 
in one module and recreate the links on a different module. - - - 
Step 
1. Reach the Delete a Link Menu from the Link Type Menu. 
2. Select to delete one link....