Mitel Voice Processing Solutions Instructions Manual

Cl? 3029 
Page 4 of 4 
VoiceMemo Release 6.OA and later 
steb Reference 
19. Reach the Smart Card Table Allocation Menu from the Offline Configuration 
Menu. 
20. Identify the module (host) that contains the SeriaI 16/32 card. 
Select: (H) Current Host Number 
Prompt: 
Current Host Number = 
Response: The number (l-4) of the module that contains the Serial 16/32 card 
host adapter card. 
2 1. Set the card type to recognize rhe Serial 16/32 card. 
Select: (E) Card type [0 - 280, 1 - RISC] 
Prompt: 
Smart...

Install a Smartcard Serial Interface 
Page 1 of 4 
VoiceMemo Release 6.OA and later 
This procedure describes how to install a Smartcard serial interface in a Series 6 server. 
ote: You cannot install both a Smartcard and a Serial 16/32 card in the same server 
module. However, you can install them in different modules in the same 
Model 640 server. You can install a maximum of three Smartcards in any one 
module. 
DANGER! 
Disconnect the system from its power source before connecting 
cables,...

cl? 3041 
Page 2 of 4 
VoiceMemo Release 6.OA and later 
Step 
@CD Install the Smartcard 
5. Remove the cover on the system. On a Model 640, remove the front panel of the 
CPU assembly. 
6. Using the plastic loops, remove the MVII? cable. You only need to remove it from 
enough cards so that you can install the Smartcard. 
7. Configure the Smartcard. 
8. Pick up the Smartcard with the connector facing away from you. 
9. Identify the correct card cage slot for the Smartcard as defined in the Technical...

Page 3 of 4 
VoiceMemo Release 6.OA and later 
Octopus Cable 
(4 port shown) 
Smartcard 
4072vm6 
Figure 1 Model 64 
onfigure the Voice 
tare 
18. Turn on the system power and wait for the system to initialize. 
19. Reach the Smart Card Table Allocation Menu from the Offline Configuration 
Menu. 
20. 11 dentify the module (host) that contains the Smartcard. 
Select: 
(H) Current Host Number 
Prompt: Current Host Number = 
Response: The number (14) of the module that contains the Smartcard. -r Reference...

cl? 3041 
Page 4 of 4 
VoiceMemo Release 6,OAand later 
Step 
2 1. Set the card type to recognize the Smartcard. 
Select: (E) Card type [0 - 280,1- RISC] 
Prompt: Smart card type [O - 280 1 - XEM RISC] = 
LO1 
Response: 0 
22. Set the number of serial interface cards in the module. 
Select: (N) Number of cards on this host. 
prompt: Number of Cards on this Host = 
Response: The number (l-3) of Smartcards installed in the module identified in 
step 20. 
23. Identify the card that you just installed in the...

Configure MESA-Net +nc Load Share CP 
Page 1 of 1 
VoiceMemo Release 6.OA and later 
This procedure describes how to configure MESA-Net Async Load Share. You can only 
enable this feature on a multiple-module Series 6 Server Model 640. Before starting this 
procedure, you must have installed Serial 16/32 cards in both modules that will carry 
Step 
MESA-Net traffic and configured the serial ports. 
@TT istributing Existing links 
1. Install the Link Enable optional feature. 
2. If you are moving existing...

Page 1 of 2 
Configure MESA-Net Async VoiceMemo Release 6.06.OA and later 
This procedure describes how to configure basic MESA-Net Async (also called 
MESA-Net Basic). Before starting this procedure you must have installed a Serial 16/32 
card or a Smartcard and configured the serial ports. 
Step Reference 
1. Install the MESA-Net Async optional feature. 
2. Reach the MESA-Net Async Network Menu. 
3. Select the module on which to configure MESA-Net Async. The module must 
contain an expansion serial...

cl? 5735 
Page 2 of 2 
Release G.OA and later 
Step 
7. Enter the system node name to be used in MESA-Net reports. 
Select: 
(S) Node Name (O-15 chars) = 
prompt: Node Name (O-15 chars) = 
Response: The name of the node. 
8. Set the limit on the longest network message that the node will accept. 
Select: (M) System Network message limit (l-99) 
prompt: Network message limit (l-99) = 
Response: The maximum message length (in minutes) that the node will accept. 
9. Verify your work by looking at the...

Connect and Configure Direct Connect 
for MESA-Net Async Cl? Page 1 of 1 
VoiceMemo Release G.OA and later 
This procedure describes how to set up a direct connection between MESA-Net Async 
nodes. You must also configure hardware types and links as described in Chapter 4. 
Step Reference 
1. Physically attach a null modem cable to each Series 6 server, either directly to a 
serial port or to a serial port option. 
2. Reach the Network Reports Menu. 
3. Check existing hardware types to see if your modem...