Mitel SX 200 ML PABX Instructions Guide

SUPERSET 410 Telephone 
REDIAL Key: The last manually dialed number is dialed when the redial key is pressed. 
CANCEL Key: This key is used to cancel a dialing sequence, end a call, terminate 
without saving a programming function, or return to a party on soft hold. 
VOLUME/TONE UP and VOLUME/TONE DOWN Keys: These two keys are used to 
adjust handset volume and ringing volume and tone. Each key depression changes 
the level up or down by one step. 
The levels for ringing volume and pitch is stored in the...

Peripheral Devices 
SUPERSE~410 Telephone Installation Instructions 
5.4 Installation includes unpacking the set, assembling the set, and connecting the set to 
a wall jack. The connections to the system via the cross connect field are described in 
the /~s&I//&~o~ 
hformation Practice. 
WARNING: ANY 
CONNECTION OF THIS SET TO AN OFF PREMISE APPLICATION, AN OUT 
OF PLANT APPLICATION, OR TO ANY OTHER EXPOSED PLANT APPLICATION 
MAY RESULT IN A SAFETY HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR 
EQUIPMENT...

SUPERSET 410 Telephone 
Wall-Mounting the SUPERSET 410 Telephone 
5.5 
To wall-mount the SUPERSET 470 telephone reverse the detachable base and plug 
the line cord into a modular jack. The “cord winder” in the base stores extra cord (See 
Figure 5-3). The complete wall-mounting instructions can be ordered through normal 
distribution channels. 
Visual Indication of System Communications Problems 
5.6 If there is either a synchronization or communication error, the Message Lamp and 
the Microphone Lamp...

Peripheral Devices 
LINE CORD INSTALLATION 
MILINK CONNECTION 
-HANDSET CORD INSTALLATION   
9 
/ WALL MOUNT BRACKET KEY HOLE PROTECTIVE LENS 
DESIGNATION CARD 
BRAND EXTENSION 
CARD AND 
PROTECTIVE LENS 
FEATURE DESlGNATlOh 
CARD AND 
PROTECTIVE LENS 
EEOO85 
Figure 5-3 SUPERSET 470 installation Instructions 
. . 
5-8 Issue 1 Revision 0 
March 1997  

6 SWfRSE~42UTelephone 
General Description 
6.1 The SURERSE~420 telephone is a DNIC-based digital telephone that provides many 
features to enhance communications in a modern business environment. It is a highly 
functional display set that includes an integral alphanumeric LCD display with 
controllable contrast. Figure 6-l shows a SUPER3342Otelephone set while Figure 
6-2 shows the layout of the faceplate. A description of the available features is 
included in the Features Descriptjon fractice. 
The...

Peripheral Devices 
LINE SELECT 
KEYS LINE STATUS 
INDICATORS 
I LINE SELECT 
KEYS 
EEOO86 
Figure 6-l 
SUPERSET 420 Telephone 
Physical Description 
General 
6.2 The dimensions of the SUPERSET 420 telephone are shown in Figure 6-2. The 
faceplate of the telephone is divided into five functional areas: 
l handset, speaker, and microphone 
l line appearance keys with status indicators 
. softkeys and LCD display 
l telephone keypad 
l fixed function keys. 
6-2 Issue 1 Revision 0 March 1997  

SUPERSET 420 Telephone 
Handset, Speaker and Microphone 
The handset mounts in a cradle on the left side of the telephone; the speaker is located 
beneath a grille between the cradle depressions. The microphone is located in the 
bottom right edge of the telephone, below the “ 0 ” on the keypad. 
Line Appearance Keys 
There are 12 Line Appearance keys arranged in two columns in the top section of the 
telephone’s faceplate. These keys may be programmed to access specific lines, 
specific features, or to...

Peripheral Devices 
7 LINE STATUS DISPLAY 
L 
LIQUID CRYSTAL DISPLAY 
, SOFTKEYS 
SuperKey 
TrmlConf 
-Ji=&Li 
FIXEI 
I WIDTH: 190 mm (7.48 INCHES) 
Figure 6-2 SUPERSET 420 Telephone Dimensions 
6-4 Issue 1 Revision 0 
March 1997  

SUPERSET 420 Telephone 
Functional Description 
Fixed Function Keys 
6.3 
Ten fixed function keys surround the keypad. Two of these keys have LED visual 
indicators. The fixed function keys are: 
HOLD Key: Pressing the red Hold key places the current call on hard hold. The call 
may be retrieved by pressing the line select key of the call on hold (next to the flashing 
line select status indicator). 
MESSAGE Key: The Message key is used to send a callback message to another 
telephone set capable of...

Peripheral Devices 
6-6 TRANWCONF Key -This key is used for Call Transferring and Conferencing. Pressing 
the key allows the user to put a call on hold, dial a new number and conference the 
call, or transfer the held call (with privacy) to a new number. 
LCD Display 
The LCD Display gives you the following information: 
l time and date when the set is idle 
l softkey labels during programming and feature access 
l call status during telephone calls 
. 
message information 
l telephone system error...