Mitel SX 200 ML PABX Instructions Guide

Table of Contents 
Controls, Indicators, and Connectors 
...................................... .9-2 
Installation 
.......................................................... .9-3 
Circuit Description 
....................................................... .9-4 
AU//W Data Module 
..................................................... .9-5 
General Description 
................................................... .9-5 
Installation 
.......................................................... .9-6...

Peripheral Devices 
Table 10-l DATASET 2100 Dip Switch Settings 
................................ 1 O-5 
Table 12-l Music-On-Hold/Pager Unit LED Indicator 
............................ 12-2 
Table A-l Maximum Loop Lengths for Peripheral Devices 
....................... A-l 
Table A-2 
Loop Lengths for SUPERSETTelephones 
........................... A-2 
List of Charts 
Chart 2-l 
Chart 2-2 
Chart 4-i 
Chart 5-l 
Chart 6-l 
Chart 7-l 
Chart 8-l 
Chart 9-l 
Chart 1 O-i Install SUPERCONSOLE 1000 Attendant...

1 Introduction 
General 
1.1 This Practice consolidates the peripheral device descriptions into one document. 
Reason for Issue 
-I .2 This section is issued to provide a general description of current peripheral devices 
used with the SX-200@ ML PABX. 
Disclaimer 
The following products have been manufacture discontinued by Mitel. These products 
are supported but not described in SX-2UO ML Practices: 
l SUPERSET 3TM and SUPERSET 4@ telephone sets 
l SUPERSET 3DNTM and SUPERSET 4DNTM telephone sets 
l...

Peripheral Devices 
l-2 Issue 1 Revision 0 March 1997  

2 Attendant Console 
Physical Description 
2.1 There are two types of Attendant consoles. 
. SUPERCONSOLE I OOOTM Attendant Console, with an RS-232 printer port and a 
tilt display 
l SUPERSET 7000TM attendant console (PC based). 
SUFERC0NS0LE 1000 Attendant Console 
2.2 The SU/?E~COIVSO~E 7000Attendant Console uses one pair of wires and interfaces 
to a Digital Line Card. The console has an RS-232 printer port and a tilt display. 
The Attendant Console, shown in Figure 2-1, weighs 2.27 kg (5.0 lbs) and...

Peripheral Devices 
The console assembly has the following external connections: 
Handset/Headset: The removable handset/headset may be connected to either of 
two jacks on the left side of the Attendant Console. 
Line Cord and Key Board: The line cord and the kev board are connected to the two 
jacks located at the rear of the Attendant Console. 
* 
Figure 2-l Attendant Console 
Functional Description 
2.3 
The Attendant Console Keyboard layout (see Figure 2-2), provides standard Call 
Handling keys....

Attendant Console 
HANDSET LIQUID 
CRYSTAL 
DISPLAY 10 DISPLAY ASSOCIATIVE 
KEYS (SOFTKEYS) 
, 
II:00 
[F3> [F4> 
[F5> 
[FW [F9> [FO> 
Di( 
[Fl>o [F2>= [F3>= [F4>0 [F5> 
[F6>0 [F7>0 [Fe> 0 [F9>0 [FO> 
Telephone Number 
Cancel Release 
0000000 1 gggE 
‘Hold 2 ,’ Hold I ,‘Answer. &&&& 
*~ooooooo omom~ 
i A 
II 
/’ /- 
7 LED 14 ATTENDANT CONSOLE 12 DIAL KEYS 
INDICATORS KEYS (FIXED KEYS) 2 VOLUME CONTROL KEYS 
2 CONTFtAST CONTROL KEYS 
4 CURSOR CONTROL KEYS 
ccooki- 
Figure 2-2 Attendant Console Keyboard...

Peripheral Devices 
Chart 2-l Install SUPERCONSOLE 7000 Attendant Console 
Step Action Comments 
Inventory, Unpack, Inspect 
1. Check off received items against packing list and 
equipment list. 
2. Unpack cartons. 
Packaging is shown in Figure 2-3. 
Assemble Console 
3. 
4. Connect the headset (or handset) to its cord. 
Plug the cord into the jack at the side of the console. The two jacks are connected in parallel; 
either can be used. 
Position Console 
5. Put the console in its assigned position....

Attendant Console 
DOCUMENTATION 
- SHIPPING 
Figure 2-3 Attendant Console Packaging 
FS232C Connector 
A printer can be attached to the SUPERCONSOLE 7000 Attendant Console via its 
RS-232C port connector which allows direct connection to most printers. The RS232C 
interface is programmable from 110 to 2400 baud, and acts like a DATASET 1101 
cartridge, with the following exceptions: 
l no autobaud 
l device ID different from that of data cartridge 
l no data loopback test. 
The RS232C connector (J3) is...

Peripheral Devices 
I 1 
Table 2-l RS-232C Port Pin Configuration - LICE 
Console Printer Port 
The Attendant does not have an indication of printer status, and does not incorporate 
the following user interface features: 
ATTN key DISC key READY LED DEVICE LED 
SUPERSET 7000 Attendant Console 
2.4 The SUPERSET 7UOO attendant console is designed to be an alternate answering 
point that operates on a PC. For example, the console can receive calls from the 
PABX when the primary attendant console(s) is...