Mitel SX 200 ML PABX Instructions Guide

Features 
Conditions The following conditions apply to this feature: 
l This feature is available only to SUPERSET 407+, SUPERSET 470, 
SUPERSET 420, and SUPERSET telephones that have been 
programmed as key system telephones. 
l A directed page or group page cannot be made to a set that has DND 
enabled. 
l A party may initiate a group page only if they are a member of a page 
group. 
l Only one group page may be performed to a page group at any one time. 
l If a telephone was listening to background...

Features Description 
SUPERSET 420 and SUPERSET 430 Telephones: 
l Dial the Direct Paging feature access code, or press the DIRECT PAGE 
feature key. 
l Dial the extension number, or press the DSS key of the party to be 
paged. 
l Broadcast the page message. 
To answer a Directed Page: 
l Lift the handset, press the flashing line key, or press the SPEAKER key. 
To initiate a Group Page: 
SUPERSET 401+ telephones: 
l Lift the handset. 
l Dial the Direct Paging feature access code. 
l Dial the end-of-dial...

Features 
Conditions The following conditions apply to this feature: 
l Personal speed call numbers may be dialed at any time on any line, 
provided that they are the first digits dialed, and that an ACD agent or 
supervisor is not currently logged in at the set. 
l There may be a maximum of five stored numbers on one telephone set. 
l The maximum length of a stored number is 25 digits. 
l This feature is available only on SUPERSET 401-t, SUPERSET 410, 
SUPERSET 420, and SUPERSET telephone sets that have...

Features Description 
Language Change 
Description 
Conditions 
Programming 
Operation This feature allows SUPERSET 420 and SUPERSET 430 telephones to 
be used with a second language. The display text and softkey text are in 
the second language. 
The language for the SUPERSET 420 and SUPERSET 430 telephones is 
selected by a softkey. The language chosen stays with the Digital Line Card 
port if the telephone itself is changed. 
None. 
Operation varies depending upon the type of set as described below....

Features 
l If a call is directed to an LDN programmed at the same key as the 
REDIAL key (softkey 9), the LDN label replaces the REDIAL softkey 
and the Redial feature is not available. 
l The REDIAL key does not appear when the console is locked out; see 
Attendant Console Lockout. 
l The redial number is lost after a system reset. 
The following conditions apply to this feature on telephones: 
. 
. 
. 
The Redial feature is not available when a consultation hold is in 
progress. 
The redial number is...

Features Description 
Attendant Console and SUPERSET 430 Telephones: 
0 Press the REDIAL softkey. 
Industry-standard and SUPERSET 401+ Telephones: 
l Lift the handset - dial tone is returned. 
l Dial the Last Number Redial feature access code. 
Last Pat-h Receives Dial Tone 
Description This feature allows the last party left on a call, after the other paAy(s) hang 
up, to receive dial tone and be able to dial. Normally, this party would receive 
silence and after 30 seconds be locked out; see Line...

Features 
Programming None. 
Operation To remove the extension from the locked-out state, go back on-hook. 
Line Privacy 
Description 
This feature ensures that calls on key lines, direct trunk select lines, private 
trunk lines and CO line keys are private. Line privacy is assigned to 
extensions and trunks. If an extension is assigned with line privacy, calls 
made from that extension are private. Other users cannot enter the call by 
selecting another appearance of the line. If a trunk is assigned...

Features Description 
Line Selection 
Description 
The SU/?E/?SE~telephones are equipped to have many line appearances 
programmed on them. When the user of the telephone initiates dialing, the 
system selects a line for dialing if programmed to do this. When the set is 
ringing and the user goes off-hook, the system selects the line to answer. 
The user can also select a specific line to place or answer a call. 
When the user goes off-hook to dial, the system checks for an available 
line appearance....

Features 
Programming Enable COS Option 604 for SU/?H?S~~ telephones to have the system 
select a line for outgoing calls. 
Operation 
None. 
Line Types and Appearances 
Description 
SUFF/?SE~telephones are equipped with keys that can be used as line 
select keys to provide additional lines to the telephones, appearances of 
other telephones, and direct access to trunk lines. 
SUfERSE~telephones have two components then - the telephone and 
the lines on the telephone. The telephone and the lines are not...

Features Description 
Conditions 
Programming Specify the delay ring time in COS Option 263, Delay Ring Timer. 
For SUPERSET telephones with heavy call traffic on several lines on the 
set, enable COS Option 611 (SUPERSETTelephone - Limited New Call 
Ring) to limit the new call ring given to the set. 
Operation None. 
2-200 2. Ring: No Ring, Delayed Ring, Immediate Ring. - This allows new calls 
to an appearance to cause a SUPERSETtelephone to ring immediately, 
ring after a delay or not ring at all....