Mitel Sx 100, Sx 200 Superswitch Volume V Instructions Manual

SECTION MITL9105/911 O-096-227-NA 
5. INSTALLATION, PROGRAMMING, AND TESTING OF MODEM LINES 
General 
5.01 This Part is concerned with configuring the SX-100’ or 
SX-200@ PABX when equipped with Associated Modem Line 
Feature to take advantage of the data features. For PABX installation 
and programming information, refer to the Installation and Program- 
ming sections, MITLS 105/9 11 O-096-200-NA and 
MITL9105/91 lo-096-210-NA. 
SUPERSET qTM Equipment Port/Modem Line Association 
5.02 In Associated...

SECTION MITL9105/91 lo-096-227-NA 
TABLE 5-2 
PROGRAM CUSTOMER DATABASE 
Step Directions 
1 
Program system customer database per standard procedures: 
Saved via Customer 
2 Enable COS option 126, for each Class-Of-Service to be assigned to: 
- SUPERSET qTM circuits with an associated data port; 
- Station circuits used for modem lines. 
3 Prepare to program SUPERSET qTM circuits which have associated modem lines. 
l Clear SUPERSET” programming by initializing data block 2 (refer to Vol- 
ume 3, PN 91...

SECTION MITL9105/911 O-096-227-NA 
LAMP SUPER 
TEST SET CANCEL 
KAO114ROEO  SET PRIME SET TRUNK MODEM NEW SET REVIEW ADD ENTER 
EQPT KEV KEY EQPT EQPT EQPT 
NUMBER NUMBER NUMBER NUMBER NUMBER 
, 1 TVPE LISTED cos 
TOLL BUSV PICKUP ANN. CONFIRM DELETE NEXT 
NUMBER NUMBER DENY LAMP GROUP EQPT 
NUMBER 
Figure 5-l SUPERSET qTM Set Extended Programming Overlay 
Page 29  

SECTION MITL9105/911 O-096-227-NA 
FRM0133RO 
Figure 5-2 SUPERSET qTM Set Programming Form 
Page 30  

SECTION MITL9105/911 O-096-227-NA 
TABLE 5-3 
Step 
1 INSTALL STATION HARDWARE 
Directions 
Verify that each Station Line circuit used for a MODEM LINE has a valid 
equipment number, and install a Line Circuit card as required. 
2 Connect Station Jacks for Modem Lines to assigned Station Line Circuits using 1 
pair of connection wires. 
Wiring Considerations 
5.03 Each modem line associated with a SUPERSET 4TM set requires 
an additional modular jack and wiring running from the jack to 
the PABX data...

SECTION MITL9105/911 O-096-227-NA 
LINE CARD 
CROSS-CONNECT 
FIELD 
TEST STATION 
Figure 5-3 Test Equipment Setup 
5.08 One modem line may be shared by several SUPERSET qTM sets. 
During SUPERSET@ set programming, the same data port equip- 
ment number is entered against each SUPERSET qTM programmed. 
Testing 
5.09 The following tests verify that the PABX data features operate 
correctly. For these tests, an industry-standard telephone is 
connected to the modem line. The PC and modem are not connected....

SECTION MITL9105/911 O-096-227-NA 
TABLE 5-4 
ASSOCIATED MODEM LINE FEATURE PROGRAMMING OPTIONS 
1 PABX 1 OPTION NAME AND TYPE 1 STATUS 
1 OPTION NUMBER 
SX-100 ASSOCIATED MODEM LINE 
sx-200 
(COS OPTION) 
TRUNK GROUP ACCESS 
(COS OPTIONS) ENABLE 
OPTION NUMBER 126 
AS REQUIRED OPTIONS 65 - 76 
SEE NOTE 1 
1, 2 
3 
NOTES: 1. (a) If the Class-of-Service of the modem line is different from that of the associated 
SUPERSET qTM set, this option must be set for both Classes-of-Service. 
(b) This option...

SECTION MITLQl OWQl 1 O-096-227-NA 
Step 
1 
2 
3 
4 
5 
6 
TABLE 5-5 
TEST ALTERNATING VOICE AND DATA CALL 
Action 
Place a call from the SUPERSET qTM set 
associated with the MODEM LINE to a trunk 
or extension number. 
Press “SWAP” softkey to transfer the call to 
the MODEM LINE. 
Press ‘SWAP” softkey to transfer the call to 
the SUPERSET qTM SET. 
Press “SWAP” softkey to transfer the call to 
the MODEM LINE. 
Set the MODEM LINE extension on-hook. 
Press the SUPERSET 4’” 
set HANG-UP 
softkey....

1. SECTION MITL9105/911 O-096-227-NA 
Step 
Step 
1 
r 
2 
I 
I 
, 
I 
I 
A 
TABLE 5-6 
TEST SIMULTANEOUS VOICE AND DATA CALLS 
Action 
Place a call FROM the SUPERSET qTM set 
associated with the MODEM LINE TO a trunl 
or extension number. 
Press the SUPERSET qTM set SWAP softkey. 
Press ‘HANG-UP’ softkey on the SUPERSET 
4TM set. 
Place a call from the SUPERSET qTM set to 
a third extension. 
Hang up the SUPERSET qTM set. 
Place the MODEM LINE extension on-hook. 
Verification 
“SWAP” softkey is...

SECTION MITL9105/911 O-096-227-NA 
TABLE 5-8 
TEST VOICE CALL FROM MODEM LINE 
Step Action Verification 
1 
Place a call FROM the MODEM LINE Destination is dialed. The call is transferred 
extension to a trunk or extension; follow to the SUPERSET qTM set. The SUPERSET 
the dialed number with a %. qTM set is placed in HANDSFREE mode. 
MODEM LINE extension is locked out. 
2 Place the MODEM LINE extension on-hook. SUPERSET qTM set is connected to the 
trunk or extension. 
3 Hang up the SUPERSET qTM set....