Mitel Sx 100, Sx 200 Superswitch Volume V Instructions Manual

SECTION MITL9105/911 O-096-227-NA 
4.08 CALL HOLD AND AUTO-HOLD 
Description 
These features allow a call to be put on hold in one of two ways: (1) 
by pressing the red HOLD key, or (2) by pressing any line select key on 
the SUPERSET qTM set. Enabling the option “Auto-Hold Disable” in a 
SUPERSET qTM set’s class-of-service inhibits placing a call on hold by 
method (2). For data calls, pressing the SWAP softkey places the call 
on hold until the data call is terminated. A voice call is retrieved from a...

SECTION MITL9105/911 O-096-227-NA 
4.09 DATA CALL 
Description 
The user can place a call to a PC using either the SUPERSET qTM set, or 
the PC. 
Conditions 
l A data call can be initiated from a SUPERSET qTM set only by 
using the prime line. 
0 A data call can be made to either an internal or external number 
using the PC. 
Operation 
To Make A Data Call From the SUPERSET qTM Set (Internally or Exter- 
nally): 
0 
Dial a database or PC number from the SUPERSET qTM set. 
0 ANSWER tone is returned from...

SECTION MITL9105/911 O-096-227-NA 
4.10 MULTIPLE PORT ASSOCIATIONS 
Description 
One Modem Line can be associated with several SUPERSET 4TM sets. 
This permits several SUPERSET qTM set users to access Associated 
Modem Line Feature’s data features through a single PC. 
Conditions 
a 
During programming of SUPERSET qTM sets, the same data port 
is programmed against MODEM EQPT NUMBER for each set. 
0 
Control of a call can be transferred from each set to the PC 
(although not simultaneously), but the PC...

SECTION MITL9105/911 O-096-227-NA 
4.11 SIMULTANEOUS VOICE AND DATA CALL (Internal and External) 
Description 
Associated Modem Line Feature permits a data call and a voice call 
to be made at the same time. On completion of the voice call, the data 
call is not affected. Voice calls may be transferred, conferenced, held, 
etc., with no effect on the data call in progress. If a simultaneous voice 
and data call is attempted, and the voice line is busy or does not 
answer, the data call may still proceed....

SECTION MITL9105/911 O-096-227-NA 
0 The PC goes on-hook for a minimum of 4 seconds, then goes 
off-hook The PC dials a data call number. Near- and far-end 
PCs are connected. 
0 The two calls progress independently of one another. 
Note: SMARTCOM and CROSSTALK do not permit a voice call to be 
dialed from the PC. If the PC dials a number followed by the 
* character, the modem will remain connected. The call will 
not be transferred to the SUPERSET qTM set. 
Page 21  

SECTION MITL91 OS/91 1 O-096-227-NA 
4.12 SUPERSET qTM SET CAMP-ON FEATURE 
Description 
This feature permits the SUPERSET qTM set user to (1) indicate to a 
called but busy party that communication is desired, or (2) signal the 
PABX that a trunk is desired when a Trunk Group is busy, and be 
connected to a trunk when one becomes free. It also permits the 
SUPERSET 41M set user who has received a camp-on signal to answer 
the camped-on party, or swap between the current party and the 
camped-on party....

SECTION MITL9105/911 O-096-227-NA 
4.13 SUPERSET qTM SET PRIVACY/PRIVACY RELEASE 
Description 
A SUPERSET qTM set user may have line appearances at his station 
which are shared with other stations. Unless otherwise selected, pri- 
vacy is automatic: another station with an appearance of the line the 
SUPERSET qTM set user has accessed cannot break into the conversa- 
tion. If desired, the SUPERSET qTM set user can permit the intrusion by 
activating the Privacy Release feature. For further information,...

SECTION MITL9105/911 O-096-227-NA 
4.14 SUPERSET qTM SET SPEED DIAL 
Description 
This feature permits the user to program a number to be dialed, on any 
unassigned SUPERSET qTM set line key. Data call numbers as well as 
voice call numbers may be stored as speed dial numbers. 
Conditions 
Refer to the SUPERSET qTM Set Features Description, Section 
MITLS 105/9 11 O-096- 107-NA. 
Operation 
Refer to the SUPERSET qTM Set Features Description, Section 
MITL9105/9 110-096-l 07-NA. 
Page 24  

SECTION MITL9105/91 lo-096-227-NA 
4.15 SUPERSET 41M SET STATION TRANSFER/CONFERENCE 
Description 
This feature permits the SUPERSET qTM set user to transfer a call, or to 
add more parties to a call. For more information, refer to the SUPER- 
SET qTM Set Features Description, Section MITL9105/9110-096-107-NA. 
Conditions 
l The Transferjionference feature is active for voice calls only. If 
a SUPERSET qTM set is engaged in any type of data call, the 
TRANSKONF softkey prompt will not appear on the...

SECTION MITL9105/911 O-096-227-NA 
4.16 SUPERSET qTM SET SWAP FEATURE 
Description 
This feature permits the SUPERSET qTM set user to SWAP between two 
voice calls (as in Broker’s Call), or 
to alternate between a voice and 
data call. Refer to the SUPERSET qTM Set Features Description, Section 
MlTL9105/91 lo-096-107-NA for operation of the SWAP feature during 
voice calls...The SWAP prompt appears at all times during either a 
voice or data call, except when the message “DATA BUSY” is dis- 
played....