Mitel Sx 100, Sx 200 Superswitch Volume V Instructions Manual

MITEL STANDARD PRACTICE SECTION MITL9105/911 O-096-227-NA 
Issue 1, February 1987 
sx-1 OO@, sx-200” 
SUPERSWITCH” 
ELECTRONIC PRIVATE AUTOMATIC BRANCH EXCHANGES 
GENERIC 217: ASSOCIATED MODEM LINE FEATURE 
DESCRIPTION AND OPERATION 
CONTENTS PAGE 
1. INTRODUCTION 
..................................... 1 
General ........................................... 1 
Reason for Issue ................................... 
1 
Associated Modem Line Feature: General Description 
....... 1 
Enhancements...

: c 
SECTION MITL9105/911 O-096-227-NA 
CONTENTS (CONT’D) PAGE 
5. INSTALLATION, PROGRAMMING, AND TESTING OF DATA 
PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 
General ..,.s.....n.......e....................... 27 
SUPERSET qTM Equipment Port/Modem Line Association . . . . 27 
Wiring Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 
Programming Considerations . . . . . . . . . . . . . . . . . . . . . . . . . -31 
Testing . . . ....

SECTION MITL9105/911 O-096-227-NA 
1. INTRODUCTION 
General 
1 .Ol Generic 217 brings integrated voice and data communications 
to MITEL’s SX-lOO@ and SX-200@ PABXs. This document de- 
scribes the features and services provided by one aspect of Generic 
217 -- Associated Modem Line Feature. 
Reason for Issue 
1.02 This Practice is issued to provide a complete description of the 
installation, programming and operation of the Generic 217 op- 
erating system’s data features contained in the Associated...

SECTION MITL9105/911 O-096-227-NA 
ASSOCIATED PC AND SUPERSET 4 SET 
& WORKSTATION SUPER&T 4 SET 
POOLED PRINTER 
TRUNKS 
AND 
EXTERNAL 
LINES 
MITEL PAEX WITH ASSOCIATED MODEM 
LINE FEATURE ENABLED 
9498ROE1 
Figure l-l ASSOCIATED MODEM LINE FEATURE - Typic& Configuration 
Page 2  

SECTION MITL9105/911 O-096-227-NA 
instructed to dial a number followed by the * character, the 
PABX passes control of the call to the SUPERSET qTM set which 
Associated Modem Line Feature associates with a modem 
line. Automatically, the SUPERSET qTM set is placed in handsfree 
mode, and the PC is disconnected from the call. When the PC is 
instructed to dial a number NOT followed by the * character, 
but followed by the # character, the PC is left connected to the 
call and is in data communication....

SECTION MITLQl OS/91 1 O-096-227-NA 
3. FUNCTIONAL DESCRIPTION 
General 
3.01 This Part outlines the general operation of Associated Modem 
Line Feature voice and data call handling. For more detailed 
information about operation, refer to Part 4 of this Practice. 
3.02 Associated Modem Line Feature associates two equipment 
ports in the PABX for each integrated voice and data commu- 
nication station. One of the two ports is assigned as a modem line, 
while the other is assigned as a SUPERSET@ port....

SECTION MITL9105/911 O-096-227-NA 
3.08 Using the SUPERSET 41M set: The SUPERSET 41M set user has 
access to all voice features available at his or her SUPERSET 
qTM set. If the user originates or receives a call, the SWAP message 
appears on the SUPERSET qTM set features display. Pressing the SWAP 
softkey gives the user access to Associated Modem Line Feature’s 
data features by transferring the call to the associated modem line. 
3.09 Using the PC: The PC can be used to dial a voice call. The 
voice...

SECTION MITL9105/911 O-096-227-NA 
3. disconnects the PC from the call, placing the modem line in a 
locked-out condition. 
Next, the PC goes on-hook, then off-hook, then dials the data call 
number, followed by the # character. The data call is connected to 
far-end PC equipment through the user’s modem. 
Note: SMARTCOM and CROSSTALK do not permit transferring con- 
trol of a call dialed from the PC to the SUPERSET qTM set 
when the call is dialed from the PC followed by the I# char- 
acter....