Mitel Sx 100, Sx 200 Superswitch Volume V Instructions Manual

SECTION MITL9105/911 O-096-227-NA 
SUPERSET qTM Set HANG-UP Feature 
3.22 The HANG-UP softkey releases the SUPERSET qTM set from a 
call. If a simultaneous voice and data call is in progress, press- 
ing HANG-UP will only terminate the voice call. If no data call is in 
progress, pressing HANG-UP will cause the seized trunk to be re- 
leased. 
DATA BUSY Message 
3.23 If a SUPERSET qTM set attempts to swap to a data call, and the 
modem line is busy, the message “DATA BUSY” appears on the 
SUPERSET qTM...

SECTION MITL9105/911 O-096-227-NA 
SUPERSET 4” 
OR 
MODEM LINE 
-I MITEL PABX 
WITH 
GENERIC 217 
AND ASSOCIATED 
MODEM LINE FEATURE TRUNK 
FAR-END 
I 
TELEPHONE 
S/STEM 
EXAMPLE 1: VOICE OR DATA CALL ONLY (EXTERNAL) 
SUPERSET 4m LINE 
MODEM LINE MITEL PABX 
WlTH 
GENERIC 217 
AND ASSOClATED 
MODEM LINE FEATURE FAR-END 
TELEPHONE 
SYSTEM 
BXAMPLE 2: ALTERNATING VOICE AND DATA CALL (EXTERNAL) -)VOICE LINE 
-+MODEM LINE 
SUPERSET 4” LINE 
MITEL PABX 
WITH 
GENERIC 217 
AND ASSOCIATED 
MODEM LINE MODEM LINE...

SECTION MlTL91 OW911 O-096-227-NA 
I I 
SUPERSFT 4’- 
--I MITEL PABX 
OR WITH 
MODEM LINE GENERIC 217 
AND ASSOCIATED 
MODEM LINE FEATURE 
EXAMPLE 1: VOICE OR DATA CA.LL ONLY (INTERNAL) -~OESTINATiON 
VOICE OR 
MODEM LINE 
EXAMPLE 2: ALTERNATING VOICE AND DATA CA.Ll. (INTERNAL) 
SUPERSET 4”” LINE 
- WITH  MITEL PABX 
GENERIC 217 
AND ASSOCIATED 
MODEM LINE MODEM LINE FEATURE 
I- DESTINATION 
MODEM LINE 
Db%MPLE 3: SIMULTANEOUS VOICE AND DATA CALL (INTERNAL) 
NOTES: MODEM LINES CONNECT TO CPMPUTER...

SECTION MITL9105/91 lo-096-227-NA 
4. DATA FEATURES DESCRIPTION 
General 
4.01 This Part describes the operation of Associated Modem Line 
Feature’s data features and call capabilities in detail. Attention 
is paid to feature requirements and conflicts, as well as to scenarios of 
the actual operation of these features. Only those features relating to 
Associated Modem Line Feature and their effect on SUPERSET qTM 
sets are described. For descriptions of system and SUPERSET@ fea- 
tures other than these,...

SECTION MITL9105/911 O-096-227-NA 
4.04 ABBREVIATED DIAL/SPEED CALL 
Description 
Abbreviated Dial (also called Speed Call) allows extensions to access 
numbers stored in common-use or personal-use tables. Numbers are 
stored against table entry numbers, and are accessed by dialing an 
access code and the table entry number. The PC can be used to dial 
Abbreviated Dial numbers. 
Conditions 
0 Abbreviated Dial numbers dialed from the PC must be followed 
by either the # character or x character. 
0 Refer...

c- 
sECTION MITL9105/911 O-096-227-NA 
4.05 ACCESS PRIVATE DATABASES 
Description 
The user can access databases which are not part of the local area 
network The call to the database is established either by 1) a direct- 
dial number, or 2) through the database service Attendant. The call to 
the database can either be made through the PC, or through the user’s 
SUPERSET qTM set. If the call is established from the SUPERSET 4TM set, 
the user can press the SWAP and then HANG-UP softkeys, making the...

SECTION MITL9105/911 O-096-227-NA 
Part B 
a Press the SWAP softkey. Pressing SWAP puts the 
SUPERSET qTM set on hold and causes the system 
to wait for an off-hook condition at the modem line 
before connecting the call. 
0 Switch on modem, and put the PC on-line using the 
commands defined in the communications software 
package. 
l The message “DATA TRANSFER” is displayed on the 
SUPERSET qTM set. SWAP and HANG-UP are the 
only active softkeys. 
l The data call is now in progress. 
To Access a Private...

SECTION MITL9105/911 O-096-227-NA 
4.06 ALTERNATING VOICE AND DATA CALL 
Description 
The user can alternate between a voice call and a data call, using the 
SUPERSET qTM set. 
Conditions 
0 When engaged in the data call, the voice call cannot be trans- 
ferred or conferenced. 
a A data call cannot be camped-on. 
0 Data calls require both the called and calling party to have 
modem-interfaced PC equipment and communications soft- 
ware. 
a Data calls can only be made from a SUPERSET qTM set using the...

SECTION MITL9105/91 lo-096-227-NA 
2. If the message “DATA BUSY” appears when the set at- 
tempts to swap to the modem line, the modem line is 
already connected to a call, or the modem is attempting 
to make a data connection. The only active softkey on the 
SUPERSET qTM set is CANCEL when “DATA BUSY” appears. 
I 
Page 15  

SECTION MITL9105/911 O-096-227-NA 
4.07 AUTOMATIC ROUTE SELECTION (ARS) 
Description 
Automatic Route selection is a software package which directs the 
PABX to place external calls using the most cost-effective route. 
Conditions 
0 
A call dialed by the PC can be routed via ARS, but the dialed 
number must be followed by either the JC character or the # 
character. 
l Refer to Section MITL9105/91 lo-096-213-NA for further in- 
formation. 
Operation 
Access ARS by using the PC to dial the ARS Access...