Miele G 7881 Service Manual

							Program Level E 03
Program
Selector
Switch
SettingDisplay Function
6 o'clock60Without dispensing in wash block 9 (SP4) (interim rinse
4)
61With DOS 1 dispensing in wash block 9 (SP4) (interim
rinse 4) direct
62With DOS 1 dispensing in wash block 9 (SP4) (interim
rinse 4) with 40°C
63With DOS 2 dispensing in wash block 9 (SP4) (interim
rinse 4) direct
64With DOS 2 dispensing in wash block 9 (SP4) (interim
rinse 4) with 40°C
65With DOS 3 dispensing in wash block 9 (SP4) (interim
rinse 4) direct
66With DOS 3 dispensing in wash block 9 (SP4) (interim
rinse 4) with 40°C
67With DOS 4 dispensing in wash block 9 (SP4) (interim
rinse 4) direct
68With DOS 4 dispensing in wash block 9 (SP4) (interim
rinse 4) with 40°C
7 o'clock70Without dispensing in wash block 10 (NS1) (final rinse 1)
71With DOS 2 dispensing in wash block 10 (NS1) (final
rinse 1) direct
72With DOS 2 dispensing in wash block 10 (NS1) (final
rinse 1) from 40°C (T5: T5
						

							2.8.4 E 04, Special Functions
–Various display functions
–With/without residual water
–Machine system lock
–Program sequence modifications
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 04
Program Selector Switch
SettingDisplay Function
1 o'clock e.g., 10DHK (steam condenser) pause time in 1-
min steps from 0 to 15 min
1)
2 o'clock20Without buzzer
21Program end indicator
22Fault indicator
23Fault and program end indicator
24Sampling indicator
25Program end and sampling indicator
26Fault and sampling indicator
27Indication of all states (program end,
faults, sampling)
3 o'clock30Without residual water in the machine
(model-dependent)
31With 4 L residual water in the machine
(model-dependent)
4 o'clock40No program sequence modification
4130 s pause before last drain cycle
(sampling)
5 o'clock50Machine locked during drying
51Machine can be opened during drying
6 o'clocke.g., 120Coarse filter operating hours
1)
e.g., 000If000is saved, the operating hours
figure is deleted1)
7 o'clocke.g., 421Fine filter operating hours
1)
e.g., 000If000is saved, the operating hours
figure is deleted1)
Table 13:Program LevelE 04
1)Only machines with drying unit and steam condenser (CD version).
2.8.5 E 05, Program-Dependent Rated Water Quantity Plus Additional Water
For programming mode access, see Programming Mode Summary, 070 4.1.
Descriptive Technical Documentation
DTD no. 62-7881 070-27
18.09.2013, US_am This information should not be duplicated or passed on without Miele approval. All rights reserved. 
						

							x
Program Level E 05
Progr-
am
Select-
or
Switch
SettingDisplayFunction (Depending on Cleaning
Program)
1
o'clock0.0Rated water quantity in accordance with
program sequence plan
0.5 ... 3.0Rated water quantity plus 0.5 L - 3 L in
0.5-L steps
5.5 AFor cleaning programs (anesthetics)
SCAN, A, B, C: (5.5 L water more than in
normal programs)
5.5 A ... 8.5 APlus 0.5 L - 8.5 L in 0.5-L steps
2
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 2 o'clock setting
3
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 3 o'clock setting
etc. . . . . . .
Table 14:Program LevelE 05
2.8.6 E 06, Program-Dependent Activation of 1st Wash Block VR1 (Prewash 1)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 06
Progr-
am
Select-
or
Switch
SettingDisplay Function (Depending on Cleaning Program)
1
o'clock1Flashing display, wash block 1 VR1 (pre-wash 1) not active
1
–Constant display, dash at top: wash block 1 VR1 (pre-wash 1)
activated with KW (cold water)
1–Constant display, dash in middle: wash block 1 VR1 (pre-wash 1)
activated with WW (hot water)
1
–Constant display, dash at bottom: wash block 1 VR1 (pre-wash 1)
activated with AD (demineralized water)
2
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 2 o'clock setting
3
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 3 o'clock setting
etc. . . . . . .
Table 15:Program LevelE 06
Descriptive Technical Documentation
070-28 DTD no. 62-7881
This information should not be duplicated or passed on without Miele approval. All rights reserved. 18.09.2013, US_am 
						

							2.8.7 E 07, Program-Dependent Activation of 2nd Wash Block VR2 (Prewash 2)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 07
Progr-
am
Select-
or
Switch
SettingDisplay Function (Depending on Cleaning Program)
1
o'clock“2”Flashing display, wash block 2 VR2 (pre-wash 2) not active
2
–Constant display, dash at top: wash block 2 VR2 (pre-wash 2) activated with
KW (cold water)
2–Constant display, dash in middle: wash block 2 VR2 (pre-wash 2) activated
with WW (hot water)
2
–Constant display, dash at bottom: wash block 2 VR2 (pre-wash 2) activated
with AD (demineralized water)
2
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 2 o'clock setting
3
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 3 o'clock setting
etc. . . . . . .
Table 16:Program LevelE 07
2.8.8 E 08, Program-Dependent Activation of 3rd Wash Block HR1 (Main Wash 1)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 08
Program
Selector Switch
SettingDisplay Function (Depending on Cleaning Program)
1 o'clock“3”Flashing display, wash block 3 HR1 (main wash 1) not
active
3
–Constant display, dash at top: wash block 3 HR1 (main
wash 1) activated with KW (cold water)
3–Constant display, dash in middle: wash block 3 HR1
(main wash 1) activated with WW (hot water)
3
–Constant display, dash at bottom: wash block 3 HR1
(main wash 1) activated with AD (demineralized water)
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 17:Program LevelE 08
Descriptive Technical Documentation
DTD no. 62-7881 070-29
18.09.2013, US_am This information should not be duplicated or passed on without Miele approval. All rights reserved. 
						

							2.8.9 E 09, Program-Dependent Temperature Setting T1 in 3rd Wash Block HR1
(Main Wash 1)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 09
Progr-
am
Select-
or
Switch
Settin-
gDispla-
yFunction (Depending on Cleaning Program)
1
o'clocke.g., 55Temperature setting in 1°C steps between 30°C and 93°C (some programs
70°C)
2
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 2 o'clock setting
3
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 3 o'clock setting
etc. . . . . . .
Table 18:Program LevelE 09
2.8.10 E 10, Program-Dependent Setting of Temperature Exposure Time t1 in Wash
Block HR1 (Main Wash 1)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 10
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock e.g., 10Setting the exposure time t1 in temperature step
T1 in 1-min steps, between 1 min and 15 min
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 19:Program LevelE 10
2.8.11 E 11, Program-Dependent Activation of 4th Wash Block HR2 (Main Wash 2)
For programming mode access, see Programming Mode Summary, 070 4.1.
Descriptive Technical Documentation
070-30 DTD no. 62-7881
This information should not be duplicated or passed on without Miele approval. All rights reserved. 18.09.2013, US_am 
						

							x
Program Level E 11
Progr-
am
Select-
or
Switch
SettingDisplay Function (Depending on Cleaning Program)
1
o'clock4Flashing display, wash block 4 HR2 (main wash 2) not active
4
–Constant display, dash at top: wash block 4 HR2 (main wash 2) activated
with KW (cold water)
4–Constant display, dash in middle: wash block 4 HR2 (main wash 2)
activated with WW (hot water)
4
–Constant display, dash at bottom: wash block 4 HR2 (main wash 2)
activated with AD (demineralized water)
2
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 2 o'clock setting
3
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 3 o'clock setting
etc. . . . . . .
Table 20:Program LevelE 11
2.8.12 E 12, Program-Dependent Temperature Setting T4 in Wash Block HR2 (Main
Wash 2)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 12
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock e.g., 55Temperature setting in 1°C steps between 30°C and
93°C (some programs 70°C)
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 21:Program LevelE 12
2.8.13 E 13, Program-Dependent Setting of Temperature Holding Time t4 in Wash
Block HR2 (Main Wash 2)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 13
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
Descriptive Technical Documentation
DTD no. 62-7881 070-31
18.09.2013, US_am This information should not be duplicated or passed on without Miele approval. All rights reserved. 
						

							Program Level E 13
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock e.g., 10Setting the holding time t4 in temperature step T4 in 1-min
steps, between 1 min and 15 min
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 22:Program LevelE 13
2.8.14 E 14, Program-Dependent Activation of 5th Wash Block CHEM-DESIN
(Chemical Disinfection)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 14
Progr-
am
Selec-
tor
Switch
Settin-
gDisplay Function (Depending on Cleaning Program)
1
o'clock5Flashing display, wash block 5 CHEM-DESIN (chemical
disinfection) not active
5Constant display without dash, wash block 5 CHEM-DESIN
(chemical disinfection) active without water intake (Combi CHEM
program only)
5
–Constant display, dash at top: wash block 5 CHEM-DESIN
(chemical disinfection) activated with KW (cold water)
5–Constant display, dash in middle: wash block 5 CHEM-DESIN
(chemical disinfection) activated with WW (hot water)
5
–Constant display, dash at bottom: wash block 5 CHEM-DESIN
(chemical disinfection) activated with AD (demineralized water)
2
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 2 o'clock setting
3
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 3 o'clock setting
etc. . . . . . .
Table 23:Program LevelE 14
2.8.15 E 15, Program-Dependent Temperature Setting T3 in Wash Block CHEM-
DESIN (Chemical Disinfection)
For programming mode access, see Programming Mode Summary, 070 4.1.
Descriptive Technical Documentation
070-32 DTD no. 62-7881
This information should not be duplicated or passed on without Miele approval. All rights reserved. 18.09.2013, US_am 
						

							x
Program Level E 15
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock e.g., 55Temperature setting in 1°C steps between 30°C and 93°C
(some programs 70°C)
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 24:Program LevelE 15
2.8.16 E 16, Program-Dependent Setting of Temperature Holding Time t3 in Wash
Block CHEM-DESIN (Chemical Disinfection)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 16
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock e.g., 5Setting the holding time t3 in temperature step T3 in 1-min
steps, between 1 min and 15 min
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 25:Program LevelE 16
2.8.17 E 17, Program-Dependent Activation of 6th Wash Block SP1 (Interim Rinse
1)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 17
Progr-
am
Selec-
tor
Switch
Settin-
gDisplay Function (Depending on Cleaning Program)
Descriptive Technical Documentation
DTD no. 62-7881 070-33
18.09.2013, US_am This information should not be duplicated or passed on without Miele approval. All rights reserved. 
						

							Program Level E 17
Progr-
am
Selec-
tor
Switch
Settin-
gDisplay Function (Depending on Cleaning Program)
1
o'clock6Flashing display, wash block 6 SP1 (interim rinse 1) not active
6
–Constant display, dash at top: wash block 6 SP1 (interim rinse 1)
activated with KW (cold water)
6–Constant display, dash in middle: wash block 6 SP1 (interim rinse 1)
activated with WW (hot water)
6
–Constant display, dash at bottom: wash block 6 SP1 (interim rinse 1)
activated with AD (demineralized water)
2
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 2 o'clock setting
3
o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning program that
can be started at the 3 o'clock setting
etc. . . . . . .
Table 26:Program LevelE 17
2.8.18 E 18, Program-Dependent Activation of 7th Wash Block SP2 (Interim Rinse
2)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 18
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock7Flashing display, wash block 7 SP2 (interim rinse 2) not
active
7
–Constant display, dash at top: wash block 7 SP2 (interim
rinse 2) activated with KW (cold water)
7–Constant display, dash in middle: wash block 7 SP2
(interim rinse 2) activated with WW (hot water)
7
–Constant display, dash at bottom: wash block 7 SP2
(interim rinse 2) activated with AD (demineralized water)
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 27:Program LevelE 18
Descriptive Technical Documentation
070-34 DTD no. 62-7881
This information should not be duplicated or passed on without Miele approval. All rights reserved. 18.09.2013, US_am 
						

							2.8.19 E 19, Program-Dependent Activation of 8th Wash Block SP3 (Interim Rinse
3)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 19
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock8Flashing display, wash block 8 SP3 (interim rinse 3) not
active
8
–Constant display, dash at top: wash block 8 SP3 (interim
rinse 3) activated with KW (cold water)
8–Constant display, dash in middle: wash block 8 SP3
(interim rinse 3) activated with WW (hot water)
8
–Constant display, dash at bottom: wash block 8 SP3
(interim rinse 3) activated with AD (demineralized water)
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 28:Program LevelE 19
2.8.20 E 20, Program-Dependent Activation of 9th Wash Block SP4 (Interim Rinse
4)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 20
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock9Flashing display, wash block 9 SP4 (interim rinse 4) not
active
9
–Constant display, dash at top: wash block 9 SP4 (interim
rinse 4) activated with KW (cold water)
9–Constant display, dash in middle: wash block 9 SP4
(interim rinse 4) activated with WW (hot water)
9
–Constant display, dash at bottom: wash block 9 SP4
(interim rinse 4) activated with AD (demineralized water)
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 29:Program LevelE 20
Descriptive Technical Documentation
DTD no. 62-7881 070-35
18.09.2013, US_am This information should not be duplicated or passed on without Miele approval. All rights reserved.