Miele Cva 6202 User Manual

If theEmpty waste unitmessage appears in
the display window after you have just cleaned
the unit out you will need to take it out of the
machine and push it back into position again and
then press the ENTER button. Otherwise the
machine will get blocked. This is a safety feature
to prevent the waste unit from overflowing. The
machine counts the number of times coffee
grounds are emptied into the waste unit. It
automatically prompts you to empty it after a
certain number of times.
Brew unit
As soon as the...

^Grasp the brew unit by the handle and press the
part marked PRESS with your thumb.
^Carefully pull the brew unit out.
If this can only be done with difficulty, it is not
correctly positioned, (see Problem solving
guide).
^Clean the brew unit thoroughly under hot running
waterwithoutwashing-up liquid.
Wipe any remaining coffee off the steel filters.
There is one filter inside the funnel and a second
one to the left of it. The second one can be
removed for cleaning (see Cleaning the filters).
^Dry the...

^Remove the brew unit.
^Fit the hexagonal key supplied to the connection
point in the brew unit, turn anti-clockwise while
gripping the filter firmly.
^Remove the filter with the screw.
^Clean the filter with hot water and dry thoroughly.
^Replace the filter in the brew unit and secure it by
carefully turning the hexagonal key clockwise,
while gently pressing down on the filter to ensure
that it is engaged correctly.
Lubricating the brew unit
^Remove the brew unit carefully.
While carrying out the...

^Clean the bolta, and smear a little silicone
lubricant on it and on the jointsb.
^Place the brew unit in the machine.
Rinsing cycle: Degreasing the brew unit
Depending on the fat content of the coffee used, the
brew unit could become blocked. It should therefore
be cleaned after approx. 500 portions have been
prepared using the cleaning tablets supplied with
the machine. These have been specially formulated
for use in this coffee machine. They are available
from your Miele Dealer or from the Miele Spare...

^Place a container, minimum capacity 0.75 litres,
under both coffee spouts.
^Press the rinsing and pre-warming buttone.
(The machine must be operational and heated up,
otherwise it will not react when the buttons are
pressed.)
The following will appear in the display:
^Press theebutton to highlight programming
option Rinsing cycle with an asterisk.
^Press ENTER.
The following will appear in the display:
A small amount of water will run out of the spouts,
then a small pause before requesting the next...

Milk frother
Always clean the steam spout immediately after use,
as it is harder to clean once milk has dried on.
^Loosen the upper locking ringaand pull the
steam spout cover downwardsb.
^Clean the cover with a mild solution of hot water
and washing up liquid or in the dishwasher, then
dry it. Make sure the steam jets are thoroughly
cleaned, especially the very small hole at the top
of the cover as this one is important for the correct
functioning of the spout.
^Push the cover back into position on the...

The machine should be descaled regularly to
ensure that it functions correctly. It will remind you
when this needs to be carried out.
When you are at the stage where only 100 portions
can be made before the next descaling programme
has to be run the following message will appear in
the display : Descale after coffees: 100.
This message will now appear on a regular basis.
When you are 30 portions away from having to
descale the machine this message will appear every
time you have made a drink. If you let...

To run the descaling programme
^Open the front of the machine.
^Remove the water container, and fill it with 2 litres
of warm water (max. 50°C). Then dissolve 2 Miele
descaling tablets in it.
^Shut the lid of the water container and replace it in
the machine.
^Close the front of the machine.
^Turn the selector anti-clockwise to the
programming position.
^Press theebutton to highlight programming
option Descaling with an asterisk.
^Press ENTER to confirm this option.
The following will appear in the...

^Place a large container (approximately 1 litre)
under the steam spout and turn the steam control
dial anti-clockwise.
The descaling process will commence automatically.
The following will appear in the display:
During the descaling programme do not open the
front of the machine or turn the selector to 0.
This would interrupt the descaling process. It will
resume when the front is closed again or the
selector is turned to another position. However
the water container will need to be refilled.
If a...

The following will appear in the display:
The machine must now be rinsed out to remove all
traces of the descaling agent.
^Rinse the water conainer out thoroughly and then
fill it with at least 2 litres of fresh, cold water and
place it back in the machine.
^Place good sized empty containers under the hot
water spout and steam spout and turn the steam
control dial anti-clockwise.
^Allow all the water to empty out of the machine via
the spouts.
This rinses through the whole system and removes
all traces...