Miele Cva 6202 User Manual

Unlike standard coffee machines, this
machine has a container forcoffee
beansso that they can be freshly
ground for every cup, to benefit fully
from the flavour.
First the ground coffee is moistened
with hot water (pre-brewing), to
develop the aroma. Next, hot water is
forced at high pressurethrough the
ground coffee. The pre-brewing
process is optional.
To prevent water from remaining in the
pipes, any water left is expelled,
resulting in a little trickle after the coffee
has been dispensed. The coffee...

To ensure that the flavour can develop
fully and be maintained for longer the
machine has an additional function to
automatically rinse and pre-warm the
system. The same function is used to
cleanthe system and the coffee spouts
after use.
Hot water from the hot water spout can
be used topre-warm the cups.
The machine can be programmed to
switch tostandby modeso it is always
ready for operation but does not
consume unnecessary electricity. This
can be programmed to happen
between 15 minutes and 3 hours...

The machine can be programmed in easy stages for
setting to your exact requirements. The following
programming options are available:
LanguageGerman, Dutch, Portuguese, Spanish,
English, Italian, French
Rinsingon, off
Water hardness
hardness 1, hardness 2, hardness 3, hardness 4
Temperature large coffee
minimum, low, medium, high, maximum
Temperature medium coffee
minimum, low, medium, high, maximum
Temperature small/espresso coffee
minimum, low, medium, high, maximum
Pre-brewingon, off, long...

To programme the machine,
^Turn the selector to the programming position. The
machine is now in programming mode and will
respond according to the symbols shown under
the buttons.
^By pressing the-orebutton
–the required programming option in the display
can be highlighted with an asterisk. Press ENTER
to select the option.
– the settings of the various programming options
can be altered.
– a time can be entered for the Standby option.
^By pressing ENTER
– a programming option highlighted with an...

Choosing a language
The language for the commands in the display can
be selected before the machine is used for the first
time.
^Turn the selector anti-clockwise to the
programming position.
The machine is now in programming mode and
will respond according to the symbols shown
under the buttons.
The following will appear in the display:
Programming option Language will be
highlighted with an asterisk.
^Press ENTER to confirm this option.
The sub-menu will appear in the display as
follows:
^
Press...

Rinsing
To remove any coffee grounds from the system the
water piping and brew unit must be rinsed through
every day before the first drink is prepared. If
programme Rinsing is set to On rinsing will start
automatically when the machine is cold and the
selector switch is set to the On position, with or
without lighting. This will warm the brew unit up at
the same time because hot water is used for the
rinse process. An appropriate message will appear
in the display.
If a drink has just been prepared the...

^Press theebutton to switch rinsing on or off.
It is a good idea to set this option to On
so that the rinse process cannot be
forgotten.
^Press ENTER tosavethis setting, or
turn the selector to 0 toundo the alterations if a
mistake has been made.
This will bring you back from the sub-menu.
Setting the water hardness
For trouble-free operation of the coffee machine,
and to ensure that the descaling reminder appears
in the display at the appropriate time, it is important
to programme in the water hardness....

^Dip the strip in your drinking water for
approximately a second, then shake off any
excess water.
The results will be evident after about 1 minute.
If the water is harder than 7.0 mmol/l or 700 mg/l
(40 °d), limescale will build up more rapidy than
with soft water. Descaling will need to be carried
out more regularly than stated to prevent
limescale damage to the machine.
Use programming option Water hardness to
programme in the water hardness.
There are four programmable levels:
Level...

^Press ENTER to confirm this option.
The sub-menu will appear in the display as
follows:
^Press theebutton to set the water hardness level
(hardness 1 - hardness 4)
^Press ENTER tosavethis setting, or
turn the selector to 0 toundo the alterations if a
mistake has been made.
This will bring you back from the sub-menu.
Selecting the temperature for drinks
The machine can be set at different temperatures to
suit varying coffee drinking habits.
Five temperature levels are available for each drink
option....

^Press theebutton to highlight programming
option Temp. L coffee for large coffee, Temp.
coffee for medium coffee or Temp. S coffee for
small/espresso coffee with an asterisk.
A different temperature can be programmed for
each drink option.
^Press ENTER to confirm this option.
Depending on the programming option selected,
the sub-menu will appear in the display as follows:
^Press theebutton to set the temperature to
minimum, low, medium, high or maximum.
^Press ENTER tosavethis setting, or
turn the...