Miele Cva 6202 User Manual

The machine has an electronic safety system that reports any problems in the
display. Most faults are easily recitifed.
Message Cause + Effect Remedy
Fill coff. beans
Ready for useThe coffee bean container is empty.
The machine is only dispensing hot
water and steam.Fill the container with coffee beans.
Brewunit block. The brew unit is dirty. The machine is
blocked.Clean the brew unit.
Brewunit. miss. The brew unit is not correctly in place.
The machine is only dispensing hot
water and steam.Remove the...

Repairs to electrical machines should only be
carried out by a suitably qualified and competent
person in accordance with local and national
safety regulations. Repairs and other work by
unqualified persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
Various messages will appear in the display to warn
of certain problems. The section “Display
messages” explains how to respond to these.
The following problems will not be indicated in the
display, but can be dealt with...

^Disconnect the machine from the mains. Switch
off at the wall and withdraw the plug from the
socket, or disconnect the mains fuse or remove
the screw-out fuse in countries where this is
applicable.
^Open the front of the machine.
^Insert a small screwdriver in the opening and
carefully push it upwardsa.
^Flip the lamp cover forwards and downwardsb.
^Rotate the lamp forwardsaand carefully pull it
outb.
^Replace with a 4 Watt fluorescent tube.
^Carefully push the tube into position until it clicks
into...

^Call the Service department.
. . . the coffee grinder makes less noise than
usual.
The coffee bean container is empty. A message will
soon appear in the display.
^Wait until the grinder makes no noise at all, then
refill the bean container with beans.
. . . the machine suddenly switches itself off.
^Is the front of the machine closed properly?
^The water temperature could be too high. The
machine will remain switched off until the water
has cooled down sufficiently.
^There could be stones in among the...

. . . coffee is not dispensed, even though the
beans have been ground and there is sufficient
water in the water container.
^Check whether the slide control for the fineness of
the coffee is at the finest setting or if the slide
control for the amount of coffee to be ground has
been set at the largest amount.
Because the process is time controlled it is possible
that the process has taken so long that there is no
time left for brewing.
^Select a slightly coarser coffee grinder setting or a
lower setting...

. . . the heating-up time is getting longer, the
amount of water coming through is incorrect and
the machine is not performing properly.
The machine needs descaling.
. . . no water comes out of the coffee spouts.
The steel filters are dirty.
^Clean the steel filters.
. . . the froth produced is not as it should be.
^Check that the grinder setting is not too coarse or
too fine.
^The coffee is no longer fresh enough.
^The coffee blend is unsuitable.
^The spouts are set too high.
^Check the temperatures the...

. . . the brew unit cannot be removed.
The brew unit can only be removed when the waste
unit has been taken out.
If the brew unit is still not removable, then it is not in
the right position.
^Close the door and switch the machine on. The
brew unit will position itself correctly.
. . . the brew unit cannot be pushed into place in
the machine.
The brew unit is not in the right position. For this the
funnel must be set a little higher and the socket
standing vertically.
To position the brew unit...

In the event of a fault which you cannot correct
yourself, or if the machine is under guarantee,
please contact:
–Your Miele Dealer
or
–The Miele Service Department (see back cover
for address).
When contacting the Service Department, please
quote the model and serial number of your machine.
These are shown on the data plate inside the
machine.
Telephone calls may be monitored and recorded
to improve our service.
After Sales Service
68 

All electrical work should be carried out by a
suitably qualified and competent person only, in
strict accordance with national and local safety
regulations.
Installation, repairs and other work by unqualified
persons could be dangerous. The manufacturer
cannot be held liable for unauthorised work.
Ensure power is not supplied to the appliance until
after installation work has been carried out.
The voltage and connected load are given on the
data plate. Please ensure these match the
household mains...

Non-rewireable plugs BS 1363
The fuse cover must be refitted when changing the
fuse, and if the fuse cover is lost, the plug must not
be used until a suitable replacement is obtained.
The colour of the correct replacement cover is that
of the coloured insert in the base of the plug, or the
colour that is embossed in words on the base of the
plug (as applicable to the design of plug fitted).
Replacement fuses should be ASTA approved to BS
1362 and have the correct rating. Replacement
fuses and fuse covers...