Miele Cva 6202 User Manual

							If theEmpty waste unitmessage appears in
the display window after you have just cleaned
the unit out you will need to take it out of the
machine and push it back into position again and
then press the ENTER button. Otherwise the
machine will get blocked. This is a safety feature
to prevent the waste unit from overflowing. The
machine counts the number of times coffee
grounds are emptied into the waste unit. It
automatically prompts you to empty it after a
certain number of times.
Brew unit
As soon as the waste unit has been cleaned, the
brew unit must be cleaned as well.
The brew unit can only be removed when the
waste unit has been taken out.
Do not use force. If the waste container can only
be removed with difficulty, it is not positioned
correctly, (see Problem solving guide).
Thebrew unit must be cleaned by hand
because the moving parts are lubricated and the
rubber seals could become brittle in a
dishwasher.
Lubricate the parts of the brew unit with the
silicone lubricant supplied when there is no more
grease on the joints, to keep the machine
working smoothly (see Lubricating the brew
unit).
Cleaning and care
51 
						

							^Grasp the brew unit by the handle and press the
part marked PRESS with your thumb.
^Carefully pull the brew unit out.
If this can only be done with difficulty, it is not
correctly positioned, (see Problem solving
guide).
^Clean the brew unit thoroughly under hot running
waterwithoutwashing-up liquid.
Wipe any remaining coffee off the steel filters.
There is one filter inside the funnel and a second
one to the left of it. The second one can be
removed for cleaning (see Cleaning the filters).
^Dry the funnel area to prevent ground coffee from
sticking to it and affecting the next drink you
make.
^Directly after cleaning, press the part marked
PRESS once.
^Slide the brew unit back into the machine along
the guiding runners,withoutpressing the part
marked PRESS, until you hear it click into place.
Cleaning the steel filters
^
Wipe any remaining coffeeoff the steel filter in
the funnel of the brew unitto keep the machine
in good working order.
The steel filter to the left of the funnelcan be
removed for thorough cleaning. Check it from time to
time to see if it is dirty and clean it whenever
necessary.
Cleaning and care
52 
						

							^Remove the brew unit.
^Fit the hexagonal key supplied to the connection
point in the brew unit, turn anti-clockwise while
gripping the filter firmly.
^Remove the filter with the screw.
^Clean the filter with hot water and dry thoroughly.
^Replace the filter in the brew unit and secure it by
carefully turning the hexagonal key clockwise,
while gently pressing down on the filter to ensure
that it is engaged correctly.
Lubricating the brew unit
^Remove the brew unit carefully.
While carrying out the following
procedure ensure that the brew unit is
correctly set up. The funnel must be set
slightly higher and the socket standing vertically
(see the illustration, or the problem solving guide).
^
Smear a little of the silicone lubricant supplied on
the jointsa, in the axlebon the runnerscand
on sealing ringd.
Replacement tubes of silicone lubricant are
available to order from your Miele Dealer or from the
Spare Parts Dept.
Cleaning and care
53 
						

							^Clean the bolta, and smear a little silicone
lubricant on it and on the jointsb.
^Place the brew unit in the machine.
Rinsing cycle: Degreasing the brew unit
Depending on the fat content of the coffee used, the
brew unit could become blocked. It should therefore
be cleaned after approx. 500 portions have been
prepared using the cleaning tablets supplied with
the machine. These have been specially formulated
for use in this coffee machine. They are available
from your Miele Dealer or from the Miele Spare Parts
Department.
To remind you to degrease the brew unit the
message Rinsing Cycle will appear in the
display after 500 portions. It will not go out until
the cleaning cycle has been carried out.
^
Three quarters fill the water container with fresh,
cold water and place it in the machine.
^
Remove the brew unit and place a cleaning tablet
in the funnel.
^
Replace the brew unit in the machine and close
the door.
Cleaning and care
54 
						

							^Place a container, minimum capacity 0.75 litres,
under both coffee spouts.
^Press the rinsing and pre-warming buttone.
(The machine must be operational and heated up,
otherwise it will not react when the buttons are
pressed.)
The following will appear in the display:
^Press theebutton to highlight programming
option Rinsing cycle with an asterisk.
^Press ENTER.
The following will appear in the display:
A small amount of water will run out of the spouts,
then a small pause before requesting the next
amount of water. This procedure is carried out 4
times. On the last rinse about half a litre of water
runs out. The whole procedure takes approx. 5
minutes.
^
At the end of the rinsing cycle, the following will
appear in the display:
The brew unit has now been cleaned of
all residues and cleaning agents. Check
that the joints of the brew unit are still
sufficiently lubricated.
Cleaning and care
55 
						

							Milk frother
Always clean the steam spout immediately after use,
as it is harder to clean once milk has dried on.
^Loosen the upper locking ringaand pull the
steam spout cover downwardsb.
^Clean the cover with a mild solution of hot water
and washing up liquid or in the dishwasher, then
dry it. Make sure the steam jets are thoroughly
cleaned, especially the very small hole at the top
of the cover as this one is important for the correct
functioning of the spout.
^Push the cover back into position on the steam
spout eaand tighten the locking ringb.
Cleaning and care
56 
						

							The machine should be descaled regularly to
ensure that it functions correctly. It will remind you
when this needs to be carried out.
When you are at the stage where only 100 portions
can be made before the next descaling programme
has to be run the following message will appear in
the display : Descale after coffees: 100.
This message will now appear on a regular basis.
When you are 30 portions away from having to
descale the machine this message will appear every
time you have made a drink. If you let it run to 0 the
machine will stop working and Descale will appear
in the display.
You cannot make any more drinks until the
descaling programme has been carried out.
For descaling you should only use thedescaling
tablets supplied. These have been specially
formulated for use in this coffee machine. They
are available from your Miele dealer or the Miele
Spare Parts Department.
Other types of descaling agents will damage the
machine and affect the taste.
Follow the instructions on the package carefully.
Otherwise the machine could get damaged.
Allow the machine to cool down before descaling
and remove the steam spout cover of the milk
frother, as this could be damaged by the
descaling agent.
Make sure that anyspillages of descaling agent
are removed immediately to avoid damage to the
machine front.
Descaling
57 
						

							To run the descaling programme
^Open the front of the machine.
^Remove the water container, and fill it with 2 litres
of warm water (max. 50°C). Then dissolve 2 Miele
descaling tablets in it.
^Shut the lid of the water container and replace it in
the machine.
^Close the front of the machine.
^Turn the selector anti-clockwise to the
programming position.
^Press theebutton to highlight programming
option Descaling with an asterisk.
^Press ENTER to confirm this option.
The following will appear in the display:
^
Place a large container (approximately 1 litre)
under the hot water spout.
Descaling
58 
						

							^Place a large container (approximately 1 litre)
under the steam spout and turn the steam control
dial anti-clockwise.
The descaling process will commence automatically.
The following will appear in the display:
During the descaling programme do not open the
front of the machine or turn the selector to 0.
This would interrupt the descaling process. It will
resume when the front is closed again or the
selector is turned to another position. However
the water container will need to be refilled.
If a smaller container is used, dont
forget to empty it at intervals.
The pump will introduce a small quantity of
descaling agent into the system, then stop for a
while to let the solution take effect. The whole
procedure takes approx. 90 minutes.
When the programme is finished, the following will
appear in the display:
^
Turn the steam control dial clockwise to the o
position.
^
Press ENTER.
Descaling
59 
						

							The following will appear in the display:
The machine must now be rinsed out to remove all
traces of the descaling agent.
^Rinse the water conainer out thoroughly and then
fill it with at least 2 litres of fresh, cold water and
place it back in the machine.
^Place good sized empty containers under the hot
water spout and steam spout and turn the steam
control dial anti-clockwise.
^Allow all the water to empty out of the machine via
the spouts.
This rinses through the whole system and removes
all traces of descaling agent.
When the water container is empty, the following will
appear in the display:
^Turn the steam control dial clockwise back to the
o position and press
ENTER.
^
If the selector is in the programming position, the
following will appear in the display window:
The machine has been descaled and
rinsed clean of any descaling agent.
^
Lubricate around the outer seal at the bottom of
the water container (see illustration) and also the
contact in the machine using the silicone lubricant
supplied.
Descaling
60