Miele Cva 6202 User Manual

							Coffee and espresso cups
^Turn the selector clockwise to the In Operation
position (with or without lighting).
If the machine is still cold the display will show the
following messages in succession:
Fresh water? to remind you to fill the water
container with cold, fresh drinking water.
If a rinsing programme is running Rinsing and then
Rinsing/Pre-warming will appear in the display
once the machine has started heating up.
Hot water will flow out of both coffee spouts  into the
drip tray. The system is now rinsed out and pre-
warmed.
Wait until the following message appears in the
display:
^Place one cup under both coffee spouts.
The coffee is always dispensed simultaneously
frombothspouts.
^
Press the coffee portion button appropriate to the
size of cup until the cup is as full as required.
Release the coffee portion button.
The grinding process appears in the display:
Setting the portion sizes
31 
						

							Warning:Leave the cup under the
spouts for a few seconds after the coffee
has been dispensed to catch any
remaining drips.
^The procedure is the same for the other two coffee
portion buttons.
The volumes of water programmed in will now be
dispensed every time.
Tea cup
To programme in the volume of water for
a tea cup, function Prog. hot water must
be switched on. (See Switching the
programmed hot water on or off).
^Turn the selector clockwise to the In Operation
position (with or without lighting).
^If the machine is still cold the display will show the
following messages in succession:
Fresh water? to remind you to fill the water
container with cold, fresh drinking water.
If a rinsing programme is running Rinsing and
then Rinsing/Pre-warming will appear in the
display once the machine has started heating up.
Hot water will flow out of both coffee spouts  into
the drip tray. The system is now rinsed out and
pre-warmed.
^
Wait until the following message appears in the
display:
Setting the portion sizes
32 
						

							^Place a tea cup under the hot water spout.
^Press the hot water buttonduntil the cup is as
full as required. Then release the hot water button
d.
There will be a few seconds delay before water is
dispensed.
The following will appear in the display during this
procedure:
The volume of hot water programmed in
will now be dispensed every time.
If the functionProgr. hot wateris switchedoff,
the machine will dispense hot water freely until the
hot water buttondis pressed again to stop it.
Setting the portion sizes
33 
						

							Important: the water piping must be rinsed
through every day and the machine cleaned
thoroughly before the first drink of coffee is
prepared. This will take place automatically if the
Rinsing programme is set to On and the
machine is cold. Hot water will run out of both
spouts into the drip tray once the machine has
heated up. The following two messages will
appear in succession in the display:
If the Rinsing programme was set to Off press
the rinse and pre-warming button to rinse out the
system (see Cleaning and care).
Before making the very first drink, the system
should be rinsed through several times to remove
any residual water still in the machine from the
quality control tests.
To prevent water from running into the
drip tray always place an empty cup
under the coffee spouts before making
the first cup of coffee. Otherwise the drip tray will
need to be emptied regularly.
Warming the system and the cups
The system and the cups should always be
pre-warmed to allow the flavour to develop and be
retained. The aroma of espresso does not react well
to cold, so the machine has a pre-warming function.
^
Turn the selector clockwise to the In Operation
position (with or without lighting).
If the selector is already in this position with the
message Standby. . . shown in the display, the
machine is in energy-saving mode. Press ENTER to
switch it into operation.
Making coffee
34 
						

							The following will appear in the display:
Wait until the following appears in the display:
Pre-warming cups
The smaller the volume of coffee/espresso, the more
important it is to pre-warm the cup.
^Place the cup under the hot water spout.
^Press the hot water buttondand half fill the cup.
^Press the hot water buttondagain to stop.
^Leave the cup for a few seconds to warm, then
pour the water away. In the meantime, pre-warm
the system.
Pre-warming the system
^
Place a cup or container under the two coffee
spouts.
The water for pre-warming will be dispensed
simultaneously frombothspouts.
^
Press the rinsing and pre-warming buttone.
The following will appear in the display:
Making coffee
35 
						

							^Press ENTER again to confirm your selection.
Hot water will be dispensed from both spouts,
warming the system. The following will appear in the
display:
^Place the empty, pre-warmed cup under both
coffee spouts and prepare the coffee.
Small/espresso, medium coffee, large
coffee
The size of portion dispensed by each of the coffee
portion buttons can be programmed in according to
individual and national tastes (see Setting the
portion sizes).
The coffee spouts are height-adjustable to suit
different sizes of cup:
^Gently pull the spouts downwards.
This ensures that coffee is dispensed directly into
the cup, giving it less chance to cool down, and
ensuring that the froth is retained.
Small/espresso, medium coffee and large coffee
are all dispensed in the same way:
^
Turn the selector clockwise to the In Operation
position (with or without lighting).
Making coffee
36 
						

							If the selector is already in this position with the
message Standby. . . shown in the display, the
machine is in energy-saving mode. Press ENTER to
switch it into operation.
The following will appear in the display:
Wait until the following appears in the display:
^Place a cup under both coffee spouts.
The coffee is always dispensed simultaneously
frombothspouts.
^Press the required coffee portion button once.
The coffee will be prepared.
Depending on the portion selected, the following will
appear in the display:
If Pre-brewing is switched on, the following will
appear in the display:
Do not open the front of the machine during the
brewing process. This would damage the
machine.
Warning:Leave the cup under the
spouts for a few seconds after the coffee
has been dispensed to catch any
remaining drips.
Making coffee
37 
						

							Cancelling preparation
^To cancel the coffee making process, press one of
the coffee portion buttons and preparation will be
stopped immediately.
To prepare two cups simultaneously
^Place a cup under each of the coffee spouts.
^Press the required coffee portion button in quick
succession to bring up two cupsgin the display.
The machine will fill the cups in two stages with a
slight pause in between. Depending on the portion
selected, the following will appear in the display:
If Pre-brewing is switched on, the following will
appear in the display after the grinding process:
Leave the cups under the spouts until
the two cups have disappeared from the
display. The process is now finished.
Making coffee
38
2x 
						

							Cappuccino
To make cappuccino you need a china or porcelain
cup, a large container such as a milk jug and milk.
Cold, low-fat milk (1.5% fat) is best for
creating froth and ideally it should be
prepared in a cold, stainless steel jug
that narrows towards the top.
^Half fill the jug/container with cold milk and
dispense a portion of espresso into a china cup.
The volume of the milk in the jug will double or
triple when frothed. If the jug is too full to start
with, the milk could overflow, leading to a risk of
scalding.
^Direct the steam spout towards the drip tray and
slowlyturn the steam control dial anti-clockwise.
Any condensed water in the spout will be
expelled.
^
As soon as steam appears from the spout, switch
the steam off by turning the control dial clockwise
to the o position.
Making coffee
39 
						

							^Position the steam spout just below the surface of
the milk in the jug andslowlyturn the steam
control dial anti-clockwise.
^Move the jug in circles until a thick froth has built
up, then lower the spout deeper into the milk to
heat the rest.
Do not let the milk boil! This would cause
the froth to collapse and a skin to form.
With a little practice, you will soon
achieve perfect results.
^Switch the steam off by turning the control dial
clockwise to the o position.
^Take the jug away from the steam spout. Carefully
pour the milk into the coffee and spoon some froth
onto the surface.
The cappuccino is ready. As a finishing
touch, sprinkle a little cocoa powder over
the froth.
Always clean the steam spout immediately after use,
as it is harder to clean once milk has dried on.
(See Cleaning and care).
Making coffee
40