Macrotel Mt-16h Installation Manual

DENY CODES FOR CLASS OF SERVICE 2 (C) (PROGRAM 
Description: 
35) 
This.p.rogram defines what leading digits in a dialing plan are to be restricted. There 
are 10 line entries (O-9) whichdefineupro 12 digits per entry. 
. 
Programming: 
1. Press [#I. - 
2. UProgramming” is displayed. 
Dial 35. 
3. ‘Deny in Class C” is displayed. 
Enter [0] to [9] to select line entry. 
‘CD X” is displayed. 
4. Enter digit sequence to be toll restricted. 
5. To erase existing digit sequence, press “HOLD” key. 
6. Press...

ALLOW CODES FOR CLASS OF SERVICE 2 (C) (PROGRAM-36) 
Description: 
This program defines what leading digits in a dialing plan are to be aIlowed. There 
are 10 line entries (O-9) which define up .to 12 digits per.entry. 
Programming: 
1. 
2. 
3. 
4. 
5. Press [#I. - 
“Programmin g” is displayed. 
Dial 36. 
“Allow in Class C” is displayed. 
Enter [0] to [9] to select line entry. 
“CA xn is displayed. 
Enter allowed diaIed digits. To erase existing digit sequence press “HOLD” key 
Press [#I to save and...

ALLOW CODES FOR CLASS OF SERVICE 3 (D) 
- 
(PROGRAM 37) 
l -Da&ptioa:. . . 
This program defmes what leading digits in a dialing plan are-to be allowed. There 
are 10 line entries (O-9) which define up to 12 digits per entry. 
Programming: 
1. Press [#J 
‘Programming” is displayed. 
2. Dial 37. 
“Allow in Class D” is displayed. 
3. Enter [0] to [9] to select line entry. 
“DA x” is displayed. 
4. Enter allowed dialed digits. 
5. To erase existing digit sequence press ‘HOLD” key. 
6. Press [#}....

TOLL RESTRICTION OVERRIDE (PROGRAM 01,02,03) 
Description: 
Allows-the system programmer to assign specific passwords for each toll class of 
service. 
With. these passwords the station users are permitted to place calls on a 
telephone set that is normally toll restricted. Also referred to a traveling class of 
service. 
Programming: 
1. Press [#] 
“Programming” is displayed 
2. Press 01 (A), 02 (B) or 03 
(C) 
‘Class: x: xxxxx” is displayed 
3. Enter new password for class of service 
4. Press [#I to...

TELEPHONE TYPE (PROGRAM 38) 
Description: 
Allowsinstaller. to definethe type of telephone assigned to each, port. 
. _ 
Programming: 
1. Press [#I. 
‘Programming” is displayed. 
2. Dial 38. 
“SLT DIAL TYPE” is displayed, then U-” is displayed. 
3. Enter [0] for keyphone, 
“1” for DTMF SLT or “2” for dial pulse SLT 
4. Press [#J to save and exit 
Conditions: 
l Default value for SLT ports is N 
l System recognizes keyphone ports automatically 
l Entry input must be all 16 digits even if only one station...

TRUNK NAMES (PROGRAM 39) **** 
Description: 
This program is tiedto enter an identification or directory name for each CO line. 
The assigned trunk in the directory will be displayed during the incoming outside 
call. 
Programming: 
1. Press[#]. 
2. Press [39]. 
“Line Directory” is displayed. 
3. Press the CO line button to be named, for example, CO line 1. 
“Line 
1:” and the current data is displayed. 
4. Press the HOLD button to clear the old data. 
5. Enter the name by using the method, such as MMC14...

ASSIGN PRIVACY (PROGRAM 41) *** 
Description: 
This enables-the system-programmer to assign privacy 
or temove privacy from all 
CO line. 
Programming: 
1. Press [#j. 
‘Programming” is displayed. 
2. Dial 
41. 
‘Privacy Enable” is displayed. 
3. Enter password 
. 
4. Enter 0 = Privacy Disable 
Enter 
1 - Privacy Enable 
5. Press [x] to save and exit. 
Conditions: 
l Default is 0 (Privacy Enabled). 
82  

CO LINE DIAL MODE SELECTION (TONE/PULSE) (PROGRAM 42) 
Description: 
This enables the system programmer 
to define which CO lines are to be classed as 
either tone dial or dial pulse lines. 
Programming: 
1. Press [#]. 
“ProgramAn g” is displayed. 
2. Dial 42. 
“Trunk Dial type” is displayed. 
“XXSXXXX~ is displayed. 0 - Dial pulse lines 
1 = DTMF lines 
3. Enter Data. 
4. Press [#] to save and exit. 
Default value is 0. 
This program requires that all digits for that field must be entered regardless if...

CO LINE ENABLED FOR SERVICE (PROGRAM 43) 
Description: 
This enables the system programmer to define 
what. lines are to be enabled in the 
system. 
Programming: 
1. Press [#I. 
yProgramming” is displayed. 
2. Dial 43. 
“Tnmk Tie” is displayed. 
0 = CO line is not connected. 
1 - CO line is connected. 
3 - E/M Tie line 
3. Enter Data. 
4. Press [#I to save and exit. 
conditions: 
l Default value is 1. 
l This program requires that all digits for that field must be entered regardless if 
the data is to be...

CO UNE DEFINITION (PROGRAM 44) 
Description: 
l This enables the system programmer to define which lines are directly connected to 
a CO line 
or to a PABX line. If ali.ne.is classed as a PABX line, no toll restriction 
will be activated. 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 44. 
“PO CO TRUNK” is displayed. 
O-PABXline 
I-COline 
3. Enter 0 or 
1. 
4. 
Press [#I to save and exit. 
conditions: 
l Default value - U 1111111”. 
l This program requires that all digits for that...