Macrotel Mt-16h Installation Manual

AUTO REDIAL AlTEMPTS (PROGRAM 75) ** 
Description: 
This enablesthe programmer to choose the number of times the system will attempt 
an auto redid. 
‘. _ 
Programming: 
1. Press [#J. 
UProgramming” is displayed. 
2. Dial 75. 
“Repeat No. of ARD” is displayed. 
Xx: (current data is displayed) 
3. Input new data. 
XX:NN (new data is displayed) 
4. Press [#I to save and exit. 
conditions: 
l Default value is 03. 
l Data range is 01 to 99 times. 
l Auto redid key must be assigned in Program 80. 
116  

TRANSFER RECALL DESTINATION (PROGRAM 76) ** 
Description: 
In the case where a single line telephone transfers a call, this program will enable the 
programmer to assign whether thecall will recall-to thesingle line telephone or the 
Operator. Valuable for automated attendant applications. 
Programming: 
1. 
2. 
3. 
4. Press [#I. 
‘Programming” is displayed. 
Dial 76. 
“TRSF TO XX” is displayed. 
Input new data. 
0 - transfer recall back to station 
1 - transfer recall to operator 
Press [#I to save and...

SINGLE LINE HOOKFLASH TIME (PROGRAM 77) ** 
Description: 
. This item allows the programmer to define the parameters of a valid hookfiash from 
a singleline telephone 
_ . . _ 
. . 
Programming: 
1. Press [#I. - 
2. 
3. 
4. 
5. 
‘Programming” is displayed. 
Dial 77. 
‘SLT FLASH TIME” is displayed. 
“LOWER LIMITXXXX” is displayed. 
Input 
4digits(0040_1980msec). 
‘UPPER LIMIT: XXXX” is displayed. 
Input 
4digits(OO60-2000). 
Press [#J to save and exit. 
Conditions: 
l Default is 0160 msec lower limit,...

DISA LINE ASSIGNMENT PROGRAM (PROGRAM 
Description: 
78) *** 
This program is used to assign lines to be used for the DISA feature. 
Programming: 
1. Press [#I. 
“Progr amming” is displayed. 
2. Dial 78. 
‘ASSIGN DISA” is displayed. 
“xxxxxxxxxX” is displayed. 
3. Enter 
0 = NOT DISA 
1 = DISA 
4. Press [#I to save and exit. 
Conditions: 
l Default value is 0000000000. 
l DISA password is assigned in program 65. 
l The program requires that all digits for that field must be entered regardless if 
the...

CENTREX/PBX CODE (PROGRAM 79) **** 
Description: 
This program enables you to inform the system of any PBX access codes (Max. 5 
tables). The system will ignore-these codes and apply toll restriction to the following 
digit as programmed. 
Programming. 
1. Press [#I. 
“Programming” is displayed. 
2. Enter [79]. 
“PABX Access Code” is displayed. 
3. Dial access code table 
1 - 5. 
4. Enter the PBX or CENTREX access code (maximum of three digits). 
The access code may include 0 - 9 and *. 
5. If you want...

STATION BASIS KEY ASSIGNMENT (PROGRAM 18) *** 
Description 
This 
program allows the system programmeror user to assign functions to the four _ - 
(4) round buttons on an individualstation basis. 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 18. 
“SIN KEY PROGRAM” is displayed. 
3. Press round button to be programmed. The default function key followed by 
the current function key is displayed. 
4. Dial the selected code from table to change function of round button. 
CODES 
133TIMER...

SOFT KEY PROGRAMMING (PROGRAM 80) 
Description: 
This feature defines what each soft key (all keys except key pad) is assigned as a 
function. 
Programming: 
1. Press [#I. - 
2. 
3. 
4. 
“Programming” is displayed. 
Dial 80. 
Press key to be programmed The default function of the key 
followed by the 
current function is displayed. 
Dial selected code from table to change function of soft key. 
-Sol - STATION 1 02 
= STATION 2 
03 = STATION 
3 04 
- STATION 4 
05 - STATION 
5 02 
- STATION 6 
07 -...

Conditions: 
l Each key programmed is a system-wide function. 
l Boss/Secretary Key only operates on the Boss Secretary station. This key is 
disabled on all other sets. 
. To assign four 
(4) 1-0~4 buttons on-station by station’basis see program 18.*** 
l See default keys, Figure 3. 
**=mQ 
***= Mv3 
123  

KEY TEST (PROGRAM 81) 
Description: 
This program item allows the installer to test all the LEDs and keys on a telephone 
set. 
Programming: 
1. Press [#I. 
2. Dial 81 %ey Test” is displayed All LED’s light and the telephone rings. 
3. Press all the keys on the telephone one-by-one to test the LEDs and determine 
their function. 
4. Lift handset from cradle then replace it to end the test. 
124  

- 
STATUS MESSAGE DISPLAY (PROGRAM 82) 
Description: 
* Station users are provided with up to 20 status messages that can be engaged from 
their telephone when leaving the office. Once activated, other users calling will 
receive a display of the status message (i.e., OUT TO LUNCH, IN A MEETING). 
Programming: 
1. 
2. 
3. 
Press [#I. 
uProgramming” is displayed. 
Dial 82. 
‘Message Writing” is displayed. 
‘MSGX:” is displayed. 
Program desired message using keypad and CO Line keys 1,2 and 3. For...