Macrotel Mt-16h Installation Manual

DO NOT DISTURB STATUS (PROGRAM 66) *** - 
Description: 
This allows the-system programmer, .on a per station basis, to allow -or deny the 
DND feature. 
Programming: 
1. 
Press [#I. 
“Programming” is displayed. 
2. Dial 66. 
‘Set DND status” is displayed. 
“C” is displayed. 
3. Enter 0 - DND Disabled 
Enter 1 - DND Enabled 
4. Press [#I to save and exit. 
conditions: 
l Default value is 1110111111111111. 
l Denying DND will disable status message function. 
l Denying DND will not affect the MUTE...

HUNT GROUP RING MODE (PROGRAM 67) *** 
Description: 
This feature enables the system programmer the flexibility to designate how 
intercom calls ring to telephones in a hunt group. 
. 
programming: 
1. Press [#I. 
2. 
3. 
4. 
5. “Programming” is displayed. 
Dial 67. 
“HNTGRP RING MODE” is displayed. 
Dial group number (l,2 or 3). 
Current ring mode is displayed. 
Enter 0 - Individual 
Enter 
1 - Distributed individual 
Enter 2 = Conditional 
Press [#I to save and exit. 
conditions: 
l Default value is...

INTERNAL PAGE ZONE ASSIGNMENTS (PROGRAM 68‘) *** 
Description: 
. This program isused.to.assign telephones t3 one of three internal page zones or all 
call 
page. _ 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 68. 
“ASSIGN PAGE ZONE” is displayed. 
Y 
xxxxxxxxxxxxxxxxxxX” is dispIayed. 
3. Enter new data for all stations: 
0 - Included in all page only 
1 - Zone 1 
2 = Zone 2 
3 - Zone 3 
4. Press [#] to save and exit. 
Conditions: 
l Default value is OOOOOOOOOOOOOOOO. 
l Program 32...

STATION HUNT GRQUPS (PROGRAM 
Description: 
69) *** 
This program is used to assign a station to one of three (3) hunt groups. 
“Programming” is displayed. 
Dial 
69. 
Programming: 
1. Press [#I. - 
2. 
3. 
4. 
5. 
“SIN HUNT GROUPS” is displayed. 
Dial group number 
(1,2 or 3) 
“Group X:” is displayed. 
Press DSS of up to 8 stations to be assigned to the hunt group. 
Press [#] to save and exit. 
conditions: 
l Default values are no stations assigned to hunt groups 
l Press hold key to erase hunt group in...

ATTENDANT KEYSET DESIGNATION (PROGRAM 7Oj 
Description: 
This feature enables the system user to define which keyset+ to act as the 
Operator’s station. 
Programming: 
1. Press [#I. 
2. 
3. 
4. ‘Programming” is displayed. 
Dial 70. 
“Attend: Ext. 04” is displayed. 
Input new data by pressing the new station’s DSS key. 
Press [#] to save and exit. 
conditions: 
l Default operator station is station 4. 
l Operator places system into night mode by pressing DND key. 
l DND feature is not allowed on the...

Description: 
The MT-16H canhave 90 System Speed Dial Numbers programmed. They are 
numbers 10-99. Each Speed Dial Number may have 30 digits. 
Programming: 
1. Press [ALM/SD] key (ALM/SD). 
“Dial Memory” is displayed. 
2. Select a number 
10-99 to store your Speed Dial Number. 
3. Dial the phone number to be stored. 
4. Press the [ALM/SD]key to 
fmish. _. 
Note: Only speed dial numbers 90-99 require the programmer to enable 
MMC.” 
Note: System speed dial bins 
90-99 require the programmer to enable user...

SYSTEM SPEED DIAL TOLL RESTRICTION (PROGRAM- 71) 
Description: 
This feature 
enables the system programmer the ability to define whether the system 
allows.or. denies long distan.ce.numbers Jn system speed dialing .to override toll 
restriction. 
Programming: 
1. Press [NJ 
uProgramming” is displayed. 
2. Dial 
71. 
yAUow 
Toll” is displayed. 
3. 0 - Allow 
speed dialing to override toll restriction. 
4. 1 - Deny speed dialing to override toll restrictiun. 
5. Press [n] to save and exit. 
conditions: 
l...

BOSS/SECRETARY COMBINATION (PROGRAM-73) ,;, 
Description: 
This. 
feau.re.&ntifies. which station is defined as boss and which station is defined as 
secretary. 
Programming: 
1. Press [#I. 
‘Progr amming” is displayed. 
2. Dial 73. 
“Boss” is displayed. 
3. Press the DSS key which is to be the Boss. 
“Boss xx Sec.” is displayed. 
4. Press the DSS key which is to be the Secretary. 
“Box xx Set xx” is displayed. 
5. Press [#I to save and exit. 
conditions: 
l There is only one Box/Secretary group 
l If...

. 
CAMP ON TONE TIMER (PROGRAM 74)** 
Description: 
This enables the programmer to select the interval of camp on tones to a station. 
Programming: 
1. Press [#I. _ 
2. 
3. 
4. 
“Programming” is displayed. 
Dial 74. 
“Camp on Tone” is displayed. 
Xx: (current data is displayed) 
Input new data. 
Xx: NN (new data is displayed) 
Press [#I to save and exit. 
Conditions: 
l Default value is 00. 
l Data range 00, lo-99 
00 - 1 
tone only 
10 - 1 tone every second 
115