Macrotel Mt-16h Installation Manual

SYSTEM INlTlALlZATlON (PROGRAM 25) . 
Description: 
This enables the system programmer the ability to initialize the system without 
turining the system power off. There-are 2 lev& of ‘initialization. 
I 
Level 1 initializes scratch pad data in RAM. 
Level 2 initializes scratch pad data and battery backed-up data in RAM. 
Prow 
1. Depress [#I 
“Programming” is displayed. 
2. Dial 25 
‘WIlTAL SYS?” is displayed. 
3. Enter password. 
4. Enter 0: Do not initialize 
Enter 1; 
Enter 2; 
5. Depress [fl....

OPTIONAL CLASS OF SERVICE (PROGRAM 26) 
Description: 
This 
enables the system user to change the toll calss of service af all telephones in the 
system. Exceptions are allowed starting with MV2. 
- 
Programming: 
1. Depress[#]. 
“Programming” is displayed. 
2. Dial 26. 
“NIGHT TOLL: X” is displayed. 
3. Enter password. 
4. Enter one of the following numbers on the dial pad to set night time toll restriction: 
0 - Same as normal toll restriction (Program 30) 
1 - For all stations to be Class B 
2 = For...

l Step 5 is only required one time. Press [#I after step 4, unless exception ‘station 
status changes. 
l . Th.i!_ program is access$le through user password. *‘+” -. 
l *‘-Mv2 
68  

EXTERNAL FORWARD (PROGRAM 27) 
Th;s enables the system user the ability to turn on and turn off External Call 
Forwarding. ._ 
- - 
Press [#I.  Description: 
1. 
2. 
3. 
4. 
5. 
6. 
“Programming” is displayed. 
Dial 27 
“EXTLFORWARD OFF (ON)” is displayed. 
Enter password. 
Enter 
[l] to turn external forwarding ON. 
Enter [0] to turn external forwarding OFF. 
Press [#I to save and exit. 
Conditions: 
l Default data is 0 (OFF’). 
l Program 45 must also be addressed before this feature will work. 
l This...

-. 
STATION TOLL CUSS OF SERVICE (PROGRAM 30) 
-’ 
Description: 
This enables the system user the flexibility to assign individual classes of service to 
each extension. 
. : 
_ _ _ .._ 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 30. 
“STN Toll Class” is displayed. 
u 
n is displayed. 
3. Enter new toll class of service for each station. 
4. Press [#I to save and exit. 
conditions: 
There are 5 classes of service (o-4): 
0 - unrestricted - Class A 
1 - Class B uses Program 33 and...

CO LINE ACCESS BY STATION USER (PROGRAM 31) 
Description: 
This program defines what stations have access to CO lines on a station by station 
basis. _:.- 
Programming: 
1. Press [#I. 
“Programmin g” is displayed. 
2. Dial 
31. 
“Trunk Access” is displayed. 
3. Press DSS key to be programmed. 
“EXT yy: xxxxxxx” is displayed. 
4. Enter the new data for all eight trunks (l-8). 
l 0 - No direct access (can access from hold and transfer). 
l 1 - Answer only. 
l 2 - Dial only. **+* 
l 3 - Answer and dial.....

INTERNAL PAGING - ALLOW OR DENY (PROGRAM 32) ‘c 
Description:~ - -. 
This 
enables the system programmer to allow or deny a station from receiving an 
internal page. 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 32. 
“Enable Page Rev” is displayed. 
“XXXXXXXXXXXXXXXX~ is displayed. 
3. Enter [O] (Deny) or [l] (Allow) for each line station. 
4. Press [fl to save and exit. 
conditions: 
l Default value is 1. 
0 Any station user can make an internal page. 
l Page overrides DND. 
. ENTRY...

CLASS OF SERVICE - TOLL RESTRICTION 
, 
Class 0 is non-restricted. Class of Service l(B) and 2(C) are the primary toll 
restriction classes. Each class has a deny table and an allow table which provides for 
definition of the dial patterns to. be restricted and allowed. Each table 
is com@ised of 
ten entry lines having twelve digits per entry. Inserting the desired allow or deny 
codes in the appropriate table line entry defines the type of restriction. 
Here is a 
sample table: 
DIALED DIGITS 
In this...

DENY CODES FOR CLASS OF SERVICE 1 (B) (PROGRAM -33) 
Description: 
This program defines what leading digits in a dialing plan are to be restricted. There 
are 10 line entries (O-9) whichdefineupto- 12 digits perentry., 
1. 
2. 
3. 
4. 
5. Press [#I. 
‘Programming” is displayed. 
Dial 33. 
“Deny in Class B” is displayed. 
Enter [0] to [9] to select line entry. 
“BD xn is displayed. 
Enter the digit sequence to be toll restricted. 
To erase existing digit sequence, press the ‘HOLD” key. 
Press [#I to save...

ALLOW CODES FOR CLASS OF SERVICE l(B) (PROGRAM 34) 
Description: 
* l This program defines what leading digits in a dialing plan are to be allowed. 
There are 10 line entries@9) which define up to 12 digits per entry: 
- 
Programming: 
1. 
Press [#I. 
“Programmed” is displayed. 
2. Dial 34. 
‘Allow in Class B” is displayed. 
3. Enter [0] to [9] to select line enrry. 
‘BA x” is displayed. 
4. Enter allowed dialed digits. 
To erase existing digit sequence, press “HOLD” key. 
5. Press [#I to save and exit....