Macrotel Mt-16h Installation Manual

Sinele Line Station Up to 10 single line telephones may be installed on-the 
Comnatibilitv MT-16H (DTMF or rotary). 
Single Line Transfer 
(Recall to Owrator)“* -.. When a single line station user transfers a CO line to an 
unanswered destination, after the transfer recall timer 
times out, the call. will return to the originator or 
operator (programmable). 
Swakemhone All telephones incorporate standard speakerphones for 
both inside and outside calls. 
5bkmha~Vk~ The volume of the voice emitting from...

System Prommuning 
with Password 
Time+ 
Tone Ringer Control 
Toll Restriction 
Tmveli~ Class of Service 
Unsurxrvised Trunk 
Conference 
Voice Simaling For security, a password is required to enter into-system 
programming. 
The call timer will automatically begin in a predetermined 
amount of time after the outside line is seized. 
The timer 
information can be displayed on your phone. 
A 3-position switch is located on the base of the telephone 
to control the volume of all tones emitted from the...

L@ Seepage16 
To complete the timely installation of the MT-16H and associated equipment, it is 
essential to establish a complete installation plan. Be sure to complete the customer 
data programmin g sheets before starting. The following sections offer a detailed 
documentary and pictorial view on the installation of the equipment with notes, as 
needed. Please read the Installation and Progr amming Sections completely before 
attempting to install the equipment. 
lNSTALLATION PRECAUTIONS 
l DO NOT run...

EQUIPMENT WERIFICATION 
Verify that all components on the packing slip are included in the boxes. For 
reference, utilize the chart below to assure that all components have been received. 
Any damaged material should immediately be reported to the carrier. Report any 
discrepancies of required equipment to MacroTel International Corporation. 
PART # DESCFUPTION 
408 KSU 2609 100 Electronic Switching System 
MT-16T 2609 102 &Line/16 Station Speakerphone 
LCD Display 2609105 LCD Display Module 
2609113...

music source and a paging amplifier, if they are to be installed. These outlets 
MUST NOT be on the same circuit as the outlet for the KSU. 
Prepare a floor plan for the keysets/SLT locations using a star (home-run) 
configuration. Include each keyset’s intercom number 5 * 16. Intercom number 
4 is assigned to the system attendant in default software.programming. 
The system location should not be exposed to direct sunlight, high humidity, 
heat, dust or strong magnetic fields (such as heavy motors or...

MT-1 6H FACILITIES LOCATION 
SHEET METAL CABINET 
+ 
t 
l-i 
C.O. LINES 
STATIONS EXTERNAL 
MUSIC 
INPUT 
I 
AC 
POWER 
CORD BAllERY 
BACKUP 
CONNECTOR 
Figure 5 
MAIN DlSTRlBUTION FRAME (MDF) 
Besureto 
connecttheframe 
ground 
station 
cables. ’ 
l 
l 
l 
Plan the location for the 66 blocks, central office connectors, KSU and any 
other assemblies included in the installation. 
Using the floor plan developed in pm-installed planning, run &pair twisted cable 
(3 pair if installing off hook voice...

TERMINATING STATION CABLES AT THE MDF - 
l Terminate each station cable at the MDF as described below: 
1. Maunt the station 66 block assembly on the MDF backboard. 
2. Ensure that each station cable is correctly labeled with the keyset/SLT intercom 
number. 
3. Using the punch down tool, terminate the cables for each set. 
TERMINATING STATION CABLES AT KEYSET/SLT 
LOCATIONS 
l Terminate the keyset/SLT end of each station cable on a Cconductor modular 
jack assembly as shown in Figure 10. 
CENTRAL OFFICE...

MOUNT THE KSU 
. 
r 
lZ6 (327lnln) 
. 
1 
Il.6 
ts-I WHEN MOUJTlM BACKBOARDTO A 
CONCRETE OR MORTOR WALL, ALWArS USE ANCHOR PLWS. 
SCREWS, SLIDE DOWN 
AND TIQHTEN SCEWS. 
Figure 6 
FRAME GROUND CONNECTIONS 
_ TOP 
I El 
B 
-- 
w- 
w- 
-- 
12 AWG SOLID COPPER 
GROUND CONNECTION 
Fii7 
32  

H Program 
Item 38 is also 
required to 
act&ate single line 
telephones 
II 01220 VOLTAGE CONNECTION 
1. Determine the proper voltage of the AC wall receptacle using a meter, if 
necessary. 
. 2. Move the.switch on the side of the KSU to the proper voltage selection. 
INSTALLING THE KEiSETS/SLT 
Unpack and inspect each keyset for damage. Along with the keyset, the box should 
contain a 6-foot line cord, a coiled handset cord, a handset, and a plastic bag of key 
designation labels. With the KSU AC power...

DIP SWITCH SETTING FOR STATIONS 7&8 ~ 
DIP 8 
DIP 3 DIP 9 
I 
DIP 4 
DIP SWTCHES 3 & 8 = Station 7 
ON = Keyset 
OFF = SLT 
DIP SVvlTCHES 4 6 9 = Station 8 
ON = Keywt 
OFF = SLT 
MAIN PCB 
Figure8 
STATION CABLING FOR SINGLE LINE PHONE 
Single line telephones should be wired exactly like the keysets to allow for easy 
upgrading to keysets.