Macrotel Mt-16h Installation Manual

SYSTEM SPEED DIALING SHEET 
l Used for extemal call forwarding. 
55  

.._..___ ____.. . . ,._. _ _ 
.’ Section 
..7-.  .(,_ .: 
, 
PROGRAMMIN@ INSTRUCTlONS 
OVERVIEW 
Progr amming of the MT-16H is a simple and easy exercise which can be performed 
from any display set. This section describes all programming options available to the 
installer and includes applicable notes where required. The program is broken down 
into five basic categories: 
1. 
2. 
3. 
4. 
5. System wide programmin g requiring the enabling of the system program mode. 
User progr amming requiring the...

EWERING I EXITING SYSTEM PROGRAMMING MODE (PROGRAM 
Description: 
, Allows programmer to-gain access to programmin g-mode for system wide or 
individual software changes. 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 20. 
“MMC Disabled” is displayed. 
3. Enter password (Default is 
1234). 
“MMC Disabled” is displayed. 
4. Dial 0 to Exit program mode. 
Dial 
1 to Enter program mode. 
Dial 
4 to set clock to 12 hour mode. 
Dial 5 to set clock to 
24 hour mode. 
5. Press [#3 to save and...

ENABLING USER PROGRAMMING MODE (PROGRAM O,)*** 
Description: 
Allows 
user to gain accesuo user programming mode. 
Programming: 
1. Press [#]. 
Y?rogr amming” is displayed. 
2. Dial 04. 
“MMC Disabled” is displayed. 
3. Enter the user password (Default is 4321). 
“MMC Disabled” is displayed. 
4. Dial 1. 
5. Press [#I to save and exit. 
Conditions: 
l The phone must be in the on-hook mode. 
0 Unit will automatically go out of progr amming mode if no data is entered in 4 
minutes. 
Note: If user password...

CHANGE USER PASSWORD (PROGRAM 05) *** - 
Description: 
This 
item allows-the system programmer or user to modify the user password. 
Programming: 
1. 
Press [#] 
“Programming” is displayed. 
2. Dial [OS]. 
“Old Password” is displayed. 
3. Enter OLD password 
=New Password” is displayed. 
4. Enter new password 
5. Press [#] to save and exit. 
Conditions: 
l Default password is 4321. 
l Password must be four digits. 
l This program is available to the user, if desired by using the user password to 
enable...

STATION ON & OFF (PROGRAM 19) **** 
Description: 
This program allows the keyset .user or technician to set the following features. 
Camp-on 
tone - When on, this feature allows the user to hear camp-on reminder 
tones. The tone is heard repeatedly at pre-programmed intervals (MMC74: CAMP 
ON TONE) 
Hot 
keypad - When on, this feature allows the user to dial directory numbers 
without having to first lift the handset or press the SPK button. 
“Programming” is displayed. 
Dial [ 191.  Programming: 
1....

MODlFlCATlON OF PASSWORD (PROGRAM 21) 
Description: 
This feature-enables the -system programmer the flexibility to modify the system 
password. Thiscontrols unauthorized-entry into the database. -: 
_ 
Programming: 
1. Press [#1. 
“Programming” is displayed. 
2. Dial 
21. 
“Old Password” is displayed. 
3. Enter in current password. 
‘New Password” is displayed. 
4. Enter in new password. 
5. Press [#] to save and exit. 
conditions: 
l Default value is 1234. 
l Valid entries are 0 - 9 and the first 6 DSS...

DTMF MUTING TO STATION USER (PROGRAM 22) 
Description: 
This feature enables the system to mute the DTMF tones to the station 
user that is 
dialing on a central office line. 
Programming: 
1. Press [#]. 
“Progriunmin g” is displayed. 
2. Dial 22. 
“DTMF MUTED” or “DTMF-ON” is displayed. 
3. Enter password. 
4. Dial 0 to enable user to hear DTMF. 
Dial 
1 to deny user to hear DTMF. 
5. Press [#] to save and exit. 
Conditions: 
l Default is ‘1” (DTMF muted). 
l If the password is incorrect, the display...

DIAL PULSE MAKE/BREAK RATllOiTOLL CHECK TIMER (PROGRAM 23) - 
Description: 
This feature enables the system programmer to define the dial pulse make/break 
ratio of a CO linecircuitrhat is classed as~otaryline. -.. -. 
Programming: 
1. Press [#I. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. “Programming” is displayed. 
Dial 23. 
“Make Ratio” is displayed. 
Enter password. 
‘Make xx” is displayed. 
Enter time by 2 digits. 
“Break: xxD is displayed. 
Enter break time by 2 digits. 
“Break 66: xx” is displayed. 
Press...

SOFTWARE VERSION OF SYSTEM AND TELEPHONE (PROGRAM 24) 
. Description: 
This feature di.$ais &the current level of sof&e being used in the main equipment. It also 
displays the version of current sofrxare in the telephone set. 
Programming 
1. Depress “d 
uProgramming” is displayed. 
2. Dial 24 
“Version” is displayed. 
3. Enter password 
“KSU: xx KTS: xx)) is displayed (version of software) 
4. Depress u*n 
“Made 
199x: xx: XX” is displayed 
(copyright date of KSU sofnvare) 
5. Depress u#“. 
Conditions:...