Macrotel Mt-16h Installation Manual

							DO NOT DISTURB STATUS (PROGRAM 66) *** - 
Description: 
This allows the-system programmer, .on a per station basis, to allow -or deny the 
DND feature. 
Programming: 
1. 
Press [#I. 
“Programming” is displayed. 
2. Dial 66. 
‘Set DND status” is displayed. 
“C” is displayed. 
3. Enter 0 - DND Disabled 
Enter 1 - DND Enabled 
4. Press [#I to save and exit. 
conditions: 
l Default value is 1110111111111111. 
l Denying DND will disable status message function. 
l Denying DND will not affect the MUTE function. 
l DND is not available on the operator station. 
l This program rquires that all digits for that field must be entered regardless if 
the data is to be changed. an incorrect entry will not change the dats upon 
exiting the program, the old data will not be modified.  
						

							HUNT GROUP RING MODE (PROGRAM 67) *** 
Description: 
This feature enables the system programmer the flexibility to designate how 
intercom calls ring to telephones in a hunt group. 
. 
programming: 
1. Press [#I. 
2. 
3. 
4. 
5. “Programming” is displayed. 
Dial 67. 
“HNTGRP RING MODE” is displayed. 
Dial group number (l,2 or 3). 
Current ring mode is displayed. 
Enter 0 - Individual 
Enter 
1 - Distributed individual 
Enter 2 = Conditional 
Press [#I to save and exit. 
conditions: 
l Default value is Individual. 
l Assign hunt group members in program 69. 
l INDIVIDUAL RING - Calls will ring the lowest station number first. Caller 
will receive busy signal if all members are busy. 
l DISTRIBUTED~~UAL-CallswiUbe~~vnongallmembersofthe 
grmrp.AbusymemberwillloseitsNminhuntsequence.Cakrwillreceivea~si%nal 
ifallmembeSambu5y. 
l CONDITIONAL - Calls will ring all members at the same time. If all members 
are busy, ringing is applied to the lowest station number if it is a keyset. 
l CAMP-ON AND CALLBACK - Features cannot be applied to groups *l, *2 
and “3. 
I 
107  
						

							INTERNAL PAGE ZONE ASSIGNMENTS (PROGRAM 68‘) *** 
Description: 
. This program isused.to.assign telephones t3 one of three internal page zones or all 
call 
page. _ 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 68. 
“ASSIGN PAGE ZONE” is displayed. 
Y 
xxxxxxxxxxxxxxxxxxX” is dispIayed. 
3. Enter new data for all stations: 
0 - Included in all page only 
1 - Zone 1 
2 = Zone 2 
3 - Zone 3 
4. Press [#] to save and exit. 
Conditions: 
l Default value is OOOOOOOOOOOOOOOO. 
l Program 32 can disable internal paging regardless of status in this program. 
0 Station can be in only one zone. 
l This program requires that all digits for that field must be entered regardless if 
the data is to be 
changed. an incorrect entry will not change the daw upon 
exiting the program, the old data will not be modified. 
. 
108  
						

							STATION HUNT GRQUPS (PROGRAM 
Description: 
69) *** 
This program is used to assign a station to one of three (3) hunt groups. 
“Programming” is displayed. 
Dial 
69. 
Programming: 
1. Press [#I. - 
2. 
3. 
4. 
5. 
“SIN HUNT GROUPS” is displayed. 
Dial group number 
(1,2 or 3) 
“Group X:” is displayed. 
Press DSS of up to 8 stations to be assigned to the hunt group. 
Press [#] to save and exit. 
conditions: 
l Default values are no stations assigned to hunt groups 
l Press hold key to erase hunt group in step 4 
l A station can be assigned to only one hunt group 
l Stations 10-16 are displayed as A-G 
l Hunt Group pilot numbers are *l, *2 and *3 
l Set ring mode in program 67 
Note: Only internal calls can he forwarded to 
a hunt group. 
I 
109  
						

							ATTENDANT KEYSET DESIGNATION (PROGRAM 7Oj 
Description: 
This feature enables the system user to define which keyset+ to act as the 
Operator’s station. 
Programming: 
1. Press [#I. 
2. 
3. 
4. ‘Programming” is displayed. 
Dial 70. 
“Attend: Ext. 04” is displayed. 
Input new data by pressing the new station’s DSS key. 
Press [#] to save and exit. 
conditions: 
l Default operator station is station 4. 
l Operator places system into night mode by pressing DND key. 
l DND feature is not allowed on the attendant keyset. 
l If DND is flashing at a rate of 250 ms on/off, this signifies the system is in the 
night mode. 
l Dialing ‘0” on a station set will ring this designated attendant station. 
l Unsupervised recalls will return to this station. 
110  
						

							Description: 
The MT-16H canhave 90 System Speed Dial Numbers programmed. They are 
numbers 10-99. Each Speed Dial Number may have 30 digits. 
Programming: 
1. Press [ALM/SD] key (ALM/SD). 
“Dial Memory” is displayed. 
2. Select a number 
10-99 to store your Speed Dial Number. 
3. Dial the phone number to be stored. 
4. Press the [ALM/SD]key to 
fmish. _. 
Note: Only speed dial numbers 90-99 require the programmer to enable 
MMC.” 
Note: System speed dial bins 
90-99 require the programmer to enable user 
MMC 
or system MMC. Bin lo-89 require user MMC to be enabled.*** 
conditions: 
l System speed dial overrides station toll restriction classes 1,2 and 3 (If allowed in 
Program 71) Station toll restriction class 4 is not overridden. 
l Each pause entered takes the place of a programmed digit. 
l To clear a number, press [Hold] key after entering memory location. 
l To insert a 3 second pause, use the [Hold] key. This can be insened after the 
first digit has been entered or any time thereafter. 
l This program is available to the user, if desired by using the user password to 
enable user programming (Program 04). +** 
l To insert a hookflash (I?), use the MSG button. *++* 
l To insert a pulse to tone changeover (C), use, the CONP button. *+**  
						

							SYSTEM SPEED DIAL TOLL RESTRICTION (PROGRAM- 71) 
Description: 
This feature 
enables the system programmer the ability to define whether the system 
allows.or. denies long distan.ce.numbers Jn system speed dialing .to override toll 
restriction. 
Programming: 
1. Press [NJ 
uProgramming” is displayed. 
2. Dial 
71. 
yAUow 
Toll” is displayed. 
3. 0 - Allow 
speed dialing to override toll restriction. 
4. 1 - Deny speed dialing to override toll restrictiun. 
5. Press [n] to save and exit. 
conditions: 
l Default is ‘0”. 
l Will not override Class 4 restriction. 
112  
						

							BOSS/SECRETARY COMBINATION (PROGRAM-73) ,;, 
Description: 
This. 
feau.re.&ntifies. which station is defined as boss and which station is defined as 
secretary. 
Programming: 
1. Press [#I. 
‘Progr amming” is displayed. 
2. Dial 73. 
“Boss” is displayed. 
3. Press the DSS key which is to be the Boss. 
“Boss xx Sec.” is displayed. 
4. Press the DSS key which is to be the Secretary. 
“Box xx Set xx” is displayed. 
5. Press [#I to save and exit. 
conditions: 
l There is only one Box/Secretary group 
l If the Boss enables DND, all ICM calls are transferred to the Secretary, CO calls 
do not forward 
l Use Program 80 to defme Boss/Secretary key. On all other key sets, this key is 
disabled. 
114  
						

							. 
CAMP ON TONE TIMER (PROGRAM 74)** 
Description: 
This enables the programmer to select the interval of camp on tones to a station. 
Programming: 
1. Press [#I. _ 
2. 
3. 
4. 
“Programming” is displayed. 
Dial 74. 
“Camp on Tone” is displayed. 
Xx: (current data is displayed) 
Input new data. 
Xx: NN (new data is displayed) 
Press [#I to save and exit. 
Conditions: 
l Default value is 00. 
l Data range 00, lo-99 
00 - 1 
tone only 
10 - 1 tone every second 
115