Macrotel Mt-16h Installation Manual

							, 
EXECUTIVE PRIORITY INTRUSION TONE - 
INTERVAL TIMER (PROGRAM 56) 
Destipdbii: ..-, 
_: _: 
This ‘timer defines the interval for iritrusion tone .when the executive prio,tity feature 
is engaged. 
Programming: 
1. Press [#I. 
“Programming is displayed. 
2. Dial 56. 
‘Override alarm” is displayed. 
3. Enter intrusion tone interval. 
00 set to 
99 set 
4. 
Press [#I to save and exit. 
conditions: 
l Intrusion tone is heard by both parties in conversation. 
l Default is 10 seconds. 
0 Duration tone is 250 msec. 
l Set data to 00 seconds if no intmsion tone is desired or enable ‘override enable 
without intrusion tone” in Program 72. 
-. 
96  
						

							, 
CO TO CO CALL 
Description: 
DURATION TIMER (PROGRAM 57) 
This parameter defines the length of time for an unsupervised conference, a DISA 
call or an external call forward connection. The connection will automatically be 
dropped when this timer expires. See MV3 
note. 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 57. 
‘CO/CO call time” is displayed. 
3. Enter number of seconds. 
Example: I0CXSEC 
4. Press [#I to save and exit. 
Conditions: 
l Default is 150 sec. 
l Allowable time is 010 set to 999 sec. 
l hiV3 allows users to extend talk time after hearing a disconnect warning tone. 
***  
						

							AUTO TIMER (PROGRAM 58) 
Description: 
. On.outgoingcalls, display sets will automatically change to the start of the call 
timer. The timer will appear in accordance with this timer. 
Programming: 
1. Press [#J. 
2. 
3. 
4. ‘Programming” is displayed. 
Dial 58. 
“Timer Delay Time” is displayed. 
Enter xx (seconds) for the start of the automatictimer function. 
Press [#I to save and exit. 
conditions: 
l Default for the start of timer is 10 seconds. 
l After user has placed an outside call, the user may start the timer sooner by 
pressing the programmable timer key. 
l User may alternate between timer display and dialed number by successively 
pressing the timer key. 
l Auto timer operates with user’s timer feature. 
98  
						

							DOOR RELEASE TIMER (PROGRAM SQ)** 
Description: 
This allows-the programmer to select the duration of door lock release timer. 
“Programming” is displayed. 
Dial 59.  Programming: 
1. Press [#]. - 
2. 
3. 
4. 
“Door Release TM” is displayed. 
%X.X SEC:” is displayed. 
Enter XXX seconds (00.1 to 10.0 seconds). 
Press [#I to 
save and exit. 
Conditions: 
Default value is 03.0 seconds. 
Door key may be assigned in Program 80 or (Program 
18).** 
99  
						

							CO. LINE RINGING MODE (PROGRAM 60) 
- 
Description: 
Thisfeatures.cnables the system programmer the flexibility. to designate how C.O. 
linesring to keysets on a system-wide basis. 
Programming: 
1. 
Depress [#I 
‘Programming” is displayed 
2. Dial 60 
3. “Incoming Ring Mode” 
is displayed. Press CO. line. 
4. Enter new data 
0 - Individual ring mode 
1 - Conditional ring mode 
2 = Unconditional ring mode 
3 - Distributed ring 
5. Depress [fi 
Programming?+ 
1. 
Depress “V 
‘Programming” is displayed 
2. Dial 60 
“Trunk Ring Type” is displayed 
3. Depress line key 
1-8 
Ring 
mode for each line is displayed 
4. Enter new data per line 
0 - Individual Ring 
1 = Conditional ring mode 
2 - Unconditional ring 
mode 
3 - Distributed ring mode 
New ring mode is displayed 
5. Depress “#” 
Conditions: 
Default value is ‘0” 
Individual ring mode: An incoming line will ring the fm non-busy station in 
the order defmed in Program 
61 for night mode. If all stations are busy, off- 
hook ringing is sent to the 
1” station programmed for the line ringing group 
(refer to Program 
61 & 62) 
If 
individual ring is programmed, a phone can transfer it’s C.O. ringing to 
another phone by using call forwarding 
Conditional ring mode: An incoming line will ring all -station(s). 
that are idle for 
that line ringing group (refer to Program 61& 62) 
Unconditional ring mode: An incoming line will ring station(s) as defined in a 
line ringing group whether they are active or idle 
Distributed’ring mode: ti incoming C.O. Ene will-ring all station(s) as defined 
in a line ringing group (refer to Program 61 & 62) 
To remove a station from the ring group, place their set in ‘do not disturb” 
100  
						

							NIGHT MODE RINGING (PROGRAM 61) ** 
Description: 
This feature.enabl~ the system 
programmer the flexibility to define which phone(s) ring on 
a per-line basis when thesystem is inthe night mode. 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 61. 
“Night Ring Assign” is displayed. 
3. Press the CO line key to be programmed Current data is displayed. 
4. Press the DSS key of each phone that is to ring. 
5. Press [#] to save and exit. 
Conditions: 
Default value has all CO lines ring station 4. 
A CO line may have a maximum of 8 stations assigned to ring. 
To modify ringing program, enter new ringing program sequence. 
Stations 10 to 16 are 
displayed as A to G, respectively. 
Field Definition: 
Line Number: 
I I 
I I I I I I 
1 2 3 4 5 6 7 8 
x x x x x x x x 
*4=Mv2 
101  
						

							DAY MODE RINGING (PROGRAM 62) 
Description: 
This-feature enables the system programmer. the flexibility to define which phone(s) 
ring on a per-line ~basiswhenthe system is in the day.mode; 
“Programming” is displayed. 
Dial 62. 
Programmifig: 
1. Press [#I. 
2. 
3. 
4. 
5. 
“Day Ring Assign” is displayed. 
Press the CO line key to be programmed Current data is displayed. 
Press the DSS key of each phone that is to ring. 
Press [#j to save and exit. 
conditions: 
l Default value has all CO lines ring to station 4. 
l A CO line may have a maximum of 8 stations assigned to ring. 
l To modify ringing program, enter new ringing program sequence. 
l Stations 10 to 16 are displayed as A to G, respectively. 
l Field Deftition: 
Line Number: 
I I I 
I I I I I 
1 2 3 
4 5 6 7 8 
x x x x x x x x 
102  
						

							DOORPHONE RING ASSIGNMENT (PROGRAM 63) 
Description: 
. . 
This feature enables the system programmer the flexibility to define which 
telephones are called.by the doorphone. 
Programming: 
1. Press [#J. 
‘Progr amming” is displayed. 
2. Dial 63. 
“Door ring assign” is displayed. 
3. Press the DSS key of each phone that is to ring. 
4. Press [#I to save and exit. 
Conditions: 
l Default value is 1,2,3,4,5,6,7,8. 
l A doorphone may ring a maximum of 8 stations. 
l Stations 10-16 are displayed as A to G respectively. 
l Field Definition: 
Station Number: 
I I I I I I I I I I I I 
I I I 
12345678AB CDEFG 
103  
						

							RING OVER PAGE (PROGRAM 64) **** 
Description: 
This-program enables&e incoming trunk calls and door call to ring 
over an 
externally 
providedspeakezwhen inthenightservice~mode.~The assigned CO lines 
will send a ring tone to the external page voice pair and ring the stations assigned in 
MMC 
#61. 
Programming: 
1. Press [#I. 
‘Programming” is displayed. 
2. Dial [64]. 
“Ring Over Page” is displayed momentarily, then the current data for all eight 
CO lines is displayed. 
3. Enter the new data for the eight CO lines as follows: 
l 0 - No ring over page. 
l 1 - Ring over page. 
4. Press [#I to save and exit. 
Conditions: 
l Default is 0. 
104  
						

							DISA SECURITY CODE (PROGRAM 65) *** 
Description: 
l This item allows the system programmer or user to modify the DISA security code. 
Programming: 
1. Press [#I. 
“Programming” is displayed. 
2. Dial 65. 
“DISA Secu Code” is displayed. 
“XxXx” Current Code is displayed. 
3. Enter new password. 
4. Press [#] to save and exit. 
Conditions: 
l Default password is 1234. 
l Password must be four (4) digits. 
l * and # are not allowed. 
l Assign DISA l&es in program 78. 
l This program is available to users, if desired, by using user password to enable 
user programming. (Program 04) 
105