Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Administration For Network Connectivity Instructions Manual

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 
171
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Configuration 5B:R8csi  R8r (2 C-LANs)  R8si 
In this configuration, a DEFINITY ECS R8r acts as a gateway between two other 
nodes — one connected via ppp to an R8csi and the other via ethernet to another R8si. 
This configuration is the same as configuration 5A except that Switch 1 has two 
C-LAN circuit packs instead of one. One C-LAN handles the ppp connection and the 
other handles the ethernet connection.  
Task Summary
The following tasks need to be completed for Switch 1, Switch 2, and Switch 3:
1  Review checklist
2  Switch 1 administration
 a  Assign node names
 b  Assign link to (via a data module) to node-2
 c  Assign link to (via a data module) to the LAN
 d  Assign link (via a data module) from C-LAN(a) to C-LAN(b)
 e  Assign link (via a data module) from C-LAN(b) to C-LAN(a)
 f  Assign processor channels
 g  Assign IP Route: C-LAN(a) to node-3
 h  Assign IP Route: C-LAN(b) to node-2
3  Switch 2 administration
 a  Enable bus bridge connectivity
 b  Assign node names
 c  Assign link (via a data module) to node-1a-ppp
 d  Assign processor channels
 e  Assign IP Route to node-3
DEFINITY
ECS R8r
ppp
Switch 1
DEFINITY ECS
Switch 3
DEFINITY ECS
Switch 2
R8si
Hub
Ethernet
R8csi
C-LAN(b)C-LAN
ppp
node-1b-ethnode-3 node-1a-pppnode-2
node-1a
node-1b
DS1
C-LAN
DS1
C-LAN(a) 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
172
4  Switch 3 administration
 a  Assign node names
 b  Assign link (via a data module) to the LAN
 c  Assign processor channels
5  Enable links and processor channels
Prerequisite Administration
There are some system administration tasks that need to be completed before you can 
proceed with the connectivity administration described in this section.
Review the checklist of prerequisite administration tasks in the Checklist for 
Prerequisite Administration  (page 54), before proceeding with the connectivity 
administration in this section. 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 
173
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
SWITCH 2 SWITCH 1 SWITCH 3
Configuration 5B
DEFINITY ECS R7csi DEFINITY ECS R7r DEFINITY ECS R7si
Processor
channelsProcessor
channelsProcessor
channelsInterface
channelsInterface
channelsInterface
channelsInterface
channels
1
2
21
23
1281
500
x(any)
6004
645001
2
31
32
256 1
5000
645001
5000
5003
645001
5000
5003
64500 1
12
13
384
Link 1 Link 1
Link 12 Link 21Link 2Link 1
x
x1
2(any)
(any)
Bus
bridge
hardware connections
Processor
UN331B
C-LAN(a)
TN799C-LAN(b)
TN799 PktInt
TN1655DS1
TN767/
TN464 DS1
TN767/
TN464
Processor bus
TDM
bus
Packet bus
ppp10BaseT
ethernet
Processor
TN790B
Processor bus
TDM bus
TDM bus
Packet bus Packet bus
NetPkt
TN794 DS1
TN767/
TN464 DS1
TN767/
TN464Processor
TN798BVoice
data
Voice
data
ppp
dataNetwork
control
UN332B
56
4321
cydfec5b EWS 051799
node-2
Ext 3020
loc 1a0413
192.168.10.12node-1a-ppp
Ext 2010
loc 1c0709
192.168.10.11node-1a
Ext 2013
loc 1c0713
192.168.10.13node-1b
Ext 2378
loc 1c0815
192.168.10.130node-1b-eth
Ext 2377
loc 1c0817
192.168.10.128node-3
Ext 3901
loc 1a0517
192.168.10.129
132465
C-LAN
TN799 C-LAN
TN799
software-defined connections 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
174
Switch 1 Task — Assign Node Names
This task assigns node names and IP addresses to each node in the network. This 
screen is administered on Switch 1. A Node Names screen must be administered on 
each switch in the network.
Note:Enter node names for Intuity AUDIX and MSA adjuncts on page 1. Enter 
node names for switches, routers, and CMS starting on page 2.
Begin
Steps
> Open Node Names form — enter  ch node-n
> Go to page 2
> Enter values.
> Submit the screen1
End
change node-names  Page 2 of 6
                             NODE NAMES
Name              IP Address  Name                IP Address
default
_________ 0__.0__.0__.0__ _______________ ___.___.___.___
node-1a-ppp 192.168.10_.11_   _______________    ___.___.___.___
node-1a
______  192.168.10_.13________________ ___.___.___.___
node-1b  ______  192.168.10_.130_______________ ___.___.___.___
node-1b-eth __  192.168.10_.128   _______________    ___.___.___.___
node-2____ 
192.168.10_.12_   _______________    ___.___.___.___
node-3____  192.168.10_.129  _______________    ___.___.___.___
Field Conditions/Comments
Name Enter unique node names for the following 6 nodes:
•C-LAN(a) PPP port on Switch 1 for the connection to Switch 2
•C-LAN(a) PPP port on Switch 1 for the connection to C-LAN(b)
•C-LAN(b) PPP port on Switch 1 for the connection to C-LAN(a)
•C-LAN(b) Ethernet port on Switch 1
•C-LAN PPP port on Switch 2.
•C-LAN Ethernet port on Switch 3
IP Address The unique IP addresses of the nodes named in the previous field. 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 
175
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Switch 1 Task — Assign Link via ppp Data Module to Switch 2
This task administers a ppp data module on Switch 1 for the ppp connection to Switch 
2. The data module associates a link number with a port address, extension number, 
and node name for the C-LAN port used for this connection.
Begin
Steps
> 
Open Data Module form — enter ad da 2010
> Enter values
add data-module 2010 
                                                                 Page 1 of x
                          DATA MODULE
    Data Extension: 2010            Name: _ppp on link 1 to node 2___
  BCC: 2
              Type: ppp
     COS: 1              Port: 01c0709 COR: 1              Link: 1_            TN: 1
       Enable Link? n
         Node Name: node-1a-ppp _
Subnet Mask: 255.255.255.0 
Establish Connection: y
DESTINATION
            Digits: 8993020
_________
      Node Name: node-2__________
              CHAP? n
Field Conditions/Comments
Type: This indicates the data-module type for this link.
Port: In this example, the C-LAN(a) circuit pack is in slot 01c07; the 
ppp connection is through port 09.
Link: The link number must be in the range 1 – 33 (for R8r), not 
previously assigned on this switch.
Enable Link? If you need to add an IP route that uses this node as a gateway, 
this field must be set to 
y before adding the IP route. Otherwise 
leave this field set to 
n until the link administration is complete; 
that is, until after all data modules and the processor channels are 
assigned, then set to 
y.
Name: Information-only; appears in list generated by the “list data 
module” command.
BCC: Bearer Capability Class. This is a display-only field.
1 of 2 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
176
> Submit the screen
End
COS
The values for these fields will be specified by the system 
administrator. COR:
TN:
Node Name: The node name for the interface defined by this data module. This 
must be a name entered on the Node Names screen.
Establish 
Connection?y means that this switch will be responsible for the call setup. 
Enter n when administering the data module for Switch 2.
Destination 
Digits:Trunk access code (899) plus extension of data module on node-2 
(3020).
Destination 
Node Name:Name of the node at the far end of this connection. Must be a 
name entered on the Node Names screen
CHAP? This field enables/disables the Challenge Handshake 
Authentication Protocol security mechanism on this link. If you 
enter y, the system will prompt for a CHAP secret (password). Field Conditions/Comments
2 of 2 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 
177
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Switch 1 Task — Assign IP Interfaces
The IP interface for each C-LAN board on the switch must be defined on the IP 
Interfaces form. Each DEFINITY switch in an IP network has one IP Interfaces form.
Begin
Steps
> Open IP Interfaces form — enter  ch ip-i
> Enter values
change ip-interfaces  Page   1 of   2 
IP Interfaces
Inter-region IP connectivity allowed?  n
Enable Net
Eth Pt Type   Slot  Code Sfx Node Name   Subnet Mask  Gateway Addr Rgn
y
   C-LAN 01c08 TN799 B node-1b-eth 255.255.255.0  .._. 1
n 255.255.255.0  n 255.255.255.0  n 255.255.255.0  
Field Conditions/Comments
Inter-region IP 
connectivity 
allowed?Enter y to allow IP endpoints (phones and trunks) to use 
MedPro resources administered in regions that are 
different from the endpoints’ regions.
Enable Eth Pt The Ethernet port must be enabled (y) before it can be 
used. The port must be disabled (n) before changes can be 
made to its attributes on this screen.
Type Enter c-lan or medpro.
Slot Enter the slot location for the circuit pack.
Code Display only. This field is automatically populated with 
TN799 for C-LAN or TN802 for MedPro.
Sfx Display only. This field is automatically populated with B 
for the TN802 and TN799.
Node name Enter the unique node name for the IP interface. The node 
name here must already be administered on the Node 
Names screen
1 of 2 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
178
Subnet Mask Enter the subnet mask associated with the IP address for 
this IP interface. (The IP address is associated with the 
node name on the Node Names screen). 
In this example, leave the default subnet mask, 
255.255.255.0, which indicates no subnetting for a Class 
C IP address.
See the discussion of subnetting , Subnetting  (page 16), 
in Chapter 1 and Configuration 1: R8r  R8si  
(page 60) in this chapter for details about subnet masks.
Gateway Addr Leave blank for this configuration. The only connection 
to this IP interface is node-3 on Switch 3, which is on the 
same subnetwork as this IP interface, so no gateway is 
needed.
In general, for connectivity to other (sub)networks, enter 
the address of a network node that will serve as the 
default gateway to the other (sub)networks.
Net Rgn Enter the region number for this IP interface. Field Conditions/Comments
2 of 2 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 
179
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Switch 1 Task — Assign Link via ethernet Data Module to the LAN
This task administers an ethernet data module on Switch 1 for the ethernet 
connection. The data module associates a link number with a port address, extension 
number, and node name for the C-LAN port used for this connection.
Begin
Steps
> Open Data Module form — enter  a da n
> Enter values
> Submit the screen
End
add data next 
                                                                  Page 1 of X
                          DATA MODULE
    Data Extension: 2377            Name: ethernet on link 2
BCC: 2
              Type: ethernet
              Port: 01c0817_
              Link: 2 
Network uses 1’s for broadcast addresses? y
Field Conditions/Comments
Type: This indicates the data-module type for this connection.
Port: Ethernet connections must be assigned to port 17 on the 
C-LAN(b) circuit pack.
Link:The link number must be in the range 1 – 33 (for R8r), not 
previously assigned on this switch.
Name: Information-only; appears in list generated by the “list data 
module” command.
Network uses 
1’s for 
broadcast 
addresses?Leave the default (y) if the private network contains only 
DEFINITY switches and adjuncts. Set to n only if the network 
includes non-DEFINITY switches that use the 0’s method of 
forming broadcast addresses. See Appendix A, “Data Module - 
type ethernet” for more information about this field. 
						

							Configuration 5B:R8csi  R8r (2 C-LANs) 
 R8si 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
180
Switch 1 Task — Assign Link via ppp Data Module to C-LAN(a)
This task administers a ppp data module on Switch 1 for the ppp connection from the 
C-LAN(b) circuit pack to the C-LAN(a) circuit pack.
Begin
Steps
> 
Open Data Module form — enter ad da 2378
> Enter values
add data-module 2378 
                                                                 Page 1 of x
                           DATA MODULE
    Data Extension: 2378  Name: _ppp on link 21 to clan(a)_
 BCC: 2
              Type: ppp
     COS: 1              Port: 01c0815 COR: 1              Link: 21TN: 1
       Enable Link? n
         Node Name: node-1b_____ 
Subnet Mask: 255.255.255.0 
Establish Connection: n
DESTINATION
            Digits: 
______
      Node Name: node-1a______               CHAP? n
Field Conditions/Comments
Type: This indicates the data-module type for this link.
Port: In this example, the C-LAN(b) circuit pack is in slot 01c08; the 
ppp connection is through port 15.
Link: The link number must be in the range 1 – 33 (for R8r), not 
previously assigned on this switch
Enable Link? If you need to add an IP route that uses this node as a gateway, 
this field must be set to 
y before adding the IP route. Otherwise 
leave this field set to 
n until the link administration is complete; 
that is, until after all data modules and the processor channels are 
assigned, then set to 
y.
Name: Information-only; appears in list generated by the “list data 
module” command.
BCC: Bearer Capability Class. This is a display-only field.
1 of 2