Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Administration For Network Connectivity Instructions Manual

							Configuration 2: R7r (+CMS)  R7csi 
91
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Destination 
NodeName of the far-end node for this channel. This must be a 
name entered on the Node Names screen. 
Destination Port A value of 0 allows any available interface channel on the 
destination node to be used for this connection. The Interface 
Channel number on the Switch-2 Processor Channel screen 
must also be set to 0.
Session - Local The Local and Remote Session numbers can be any value 
between 1 and 256 (si model) or 384 (r model), but they must 
be consistent between endpoints. For each connection, the 
Local Session number on this switch must equal the Remote 
Session number on the remote switch and vice versa.
It is allowed, and sometimes convenient, to use the same 
number for the Local and Remote Session numbers. It is 
allowed, but not recommended, to use the same Session 
numbers for two or more connections. Session - 
Remote
Mach ID This field is not used for CMS.
Processor Channel 21: (ethernet connection to Switch 1)
Enable Set to y.
Appl.dcs indicates that this connection will carry DCS data.
ModeNode-5 will be the “client” on this session. Set node-1 (on 
Switch 1) to “server” (s).
Interface Link This must match the link number assigned on the node-5 data 
module screen.
Interface Chan A value of 0 allows any available interface channel to be used 
for this connection. The Destination Port number on the 
Switch-1 Processor Channel screen must also be set to 0.
Destination 
NodeName of the far-end node for this channel. This must be a 
name entered on the Node Names screen.
Destination Port This number must match the Interface Channel number 
assigned on the Switch-1 Processor Channel screen. Field Conditions/Comments
2 of 3 
						

							Configuration 2: R7r (+CMS)  R7csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
92
> Submit the screen
End
Intuity System Administration
Procedure OverviewThe following is a checklist of procedures that must be completed to administer a 
DEFINITY ECS with a TCP/IP connection to a Lucent Intuity system. The 
DEFINITY administration procedures are described in DEFINITY ECS 
Administrator’s Guide, 555-233-502 and in previous sections of this chapter. The 
Intuity system administration procedures are describe following the checklist.
For a complete description of the administration procedures for connecting an Intuity 
system to a DEFINTIY ECS, see Intuity Messaging Solutions — Using a LAN to 
Integrate with DEFINTIY ECS, 585-313-602 for Intuity R4.4 or 585-313-604 for 
Intuity R5.
DEFINITY ECS administration
The following procedures must be done on the host switch:
•Administer the local node number in the dial plan.
•Administer the Intuity system voice ports as stations, including Class of 
Restriction (COR) and Class of Service (COS).
•If the switch is a csi model, assign the bus bridge.
•Assign node names for the Intuity system and the switch.
•Administer a hunt group, and add the Intuity system voice ports to that hunt 
group.
•Add an ethernet data module.
•Administer a processor channel for the link from the switch to the Intuity system.
•Enable the link on the ethernet data module.
•Set up a coverage path for access to the voice port hunt group. Session - Local The Local and Remote Session numbers can be any value 
between 1 and 256 (si model) or 384 (r model), but they must 
be consistent between endpoints. For each connection, the 
Local Session number on this switch must equal the Remote 
Session number on the remote switch and vice versa.
It is allowed, and sometimes convenient, to use the same 
number for the Local and Remote Session numbers. It is 
allowed, but not recommended, to use the same Session 
numbers for two or more connections. Session - 
Remote
Mach ID Destination switch ID. This is the Local Node Number on the 
dial plan of the destination switch. Field Conditions/Comments
3 of 3 
						

							Configuration 2: R7r (+CMS)  R7csi 
93
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
•Apply the coverage path to stations, and if the switch is an r model, specify the 
node name of the Intuity system for each station that has a voice mailbox on the 
Intuity system.
Intuity system administration
The following procedures must be done on the Intuity system:
•Administer the UNIX name and IP address for the Intuity system.
•Administer the switch interface link to the host switch. This includes the 
Extension Length, Host Switch Number, AUDIX Number, Switch Number, 
Switch IP Address, and TCP Port.
•Administer extension numbers, channels, and services.
•Administer subscribers.
Administer the TCP/IP 
Network AddressingDo the following procedures to administer the Intuity system.
If not already done, you must set up the basic networking addressing for the Intuity 
system. Do the following:
1  Beginning at the Lucent INTUITY Main menu, select: 
The system responds with the Network Addressing window.
2  Use Worksheet A to enter the correct values in this window.
3  Press F3 (Save).
4  Continue with the next procedure, “Administer Switch Interface.”
>  Network Ad d ressing
>  TCP/IP Ad ministration
+-------------------------------------------------------+
+ Network Addressing +
+-------------------------------------------------------+
| TCP/IP Interface: eeE_0|
| Host Name: denaudix|
|IP Address: 192.168.1.125 |
Subnet Mask: 192.168.1.224|
|Default Gateway IP Address: 192.168.1.97|
+-------------------------------------------------------+ 
						

							Configuration 2: R7r (+CMS)  R7csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
94
Administer the Switch 
InterfaceYou must now administer the switch interface. Do the following.
1  Starting at the Lucent INTUITY Main menu, select:
The system responds with the Switch Interface Administration window.
2  Use Worksheet B to enter the correct values in this window.
3  Press F3 (Save).
4  Continue with the next procedure, “Administer Extension Numbers, Channels, 
and Services.”
Administer Extension 
Numbers, Channels, 
and ServicesTo associate the switch voice ports, you must do the following on the Intuity system:
•Map channels to switch extensions
•Map services to channels
•Assign services to called numbers.
For more information on this, see “Administering Channels” in the Lucent I
NTUITY 
Messaging Solutions Release 5 documentation.
Continue with the next procedure, “Administer Subscribers.”
> Switch Link Administration
> Call Data Interface Administration
> Switch Interface Administration
+-------------------------------------------------------------------------+
+                 Switch Interface Administration  +
+-------------------------------------------------------------------------+
| Switch Link Type: LAN Country: UNITED STATES |
| Extension Length: 4 Switch: DEFINITY OVERLAN |
| Host Switch Number: 1   |
| AUDIX Number: 1                                                  |
||
|Switch IP Address/ TCP Switch IP Address/ TCP |
|Number Host Name Port Number Host Name Port |
|   1  192.168.1.124 5002   |
| |
| |
| |
| | 
						

							Configuration 2: R7r (+CMS)  R7csi 
95
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Administer Subscribers
Subscribers must be administered on the Intuity system. For more information on this, 
see the Lucent I
NTUITY Messaging Solutions Release 5 documentation. The following 
screens show examples of subscriber screens on the Intuity system.
add subscriber 3066 Page 1 of 2
                                 SUBSCRIBER
         Name: Jean Collins Locked? n
    Extension: 150                                  Password:
          COS: class00                         Miscellaneous:
Switch Number: 1                          Covering Extension: 161
 Community ID: 1                           Broadcast Mailbox? n
Secondary Ext:
Account Code:
add subscriber 3066 Page 2 of 2
SUBSCRIBER CLASS OF SERVICE PARAMETERS
Addressing Format: extension Login Announcement Set: System
System Multilingual is ON  Call Answer Primary Annc. Set: System
Call Answer Language Choice? n  Call Answer Secondary Annc. Set: System
PERMISSIONS
Type: call-answer Announcement Control? y Outcalling? n            
Priority Messages? n   Broadcast: none  IMAPI Access? y
IMAPI Message Transfer? n  Fax Creation? n Trusted Server Access? y
INCOMING MAILBOX          Order: fifo               Category Order: nuo
  Retention Times (days),   New: 10       Old: 10         Unopened: 10
OUTGOING MAILBOX          Order: fifo               Category Order: unfda
Retention Times(days), File Cab: 10       Delivered/Nondeliverable: 5
Voice Mail Message (seconds),  Maximum Length: 300  Minimum Needed: 32
Call Answer Message (seconds), Maximum Length: 120  Minimum Needed: 8
        End of Message Warning Time (seconds):
          Maximum Mailing Lists: 25     Total Entries in all Lists: 250
Mailbox Size (seconds), Maximum: 3600  Minimum Guarantee: 0 
						

							Configuration 2: R7r (+CMS)  R7csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
96
Worksheet A: Names and IP Addresses for Lucent Intuity System
Complete the information on this worksheet to collect information required to 
administer the Lucent I
NTUITY system for integration with the switch.
Field Recommended Your Entry
Intuity System TCP/IP Administration Screen (TCP/IP Administration, Network 
Addressing or Networking Administration, TCP/IP Administration)
TCP/IP Interface eeE_0
Host Name 
(called UNIX Machine Name on R4.4)
This information may already be 
administered. If not, enter the UNIX name 
for this machine. The name is 
case-sensitive.
denaudix
IP Address
IP address administered on the Lucent 
Intuity system
192.168.1.125
Subnet Mask 192.168.1.224
Default Gateway IP Address 192.168.1.97 
						

							Configuration 2: R7r (+CMS)  R7csi 
97
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Worksheet B: LAN Data for the Lucent Intuity System
Complete the information on this worksheet to administer the Lucent INTUITY system 
for integration with the switch.
Field Recommended Your Entry
Lucent INTUITY System Switch Interface Administration Window
Extension Length
Use the extension length from the switch dial 
plan
4
Host Switch Number
Use 1 if the integration supports only one 
DEFINITY switch. If more than one 
DEFINITY system will be supported, use the 
number administered on the Local Node 
Number field in the host switch dial plan.
1
AUDIX Number
The number assigned to the Lucent INTUITY 
system on the DEFINITY ECS. For r-model 
switches, a number from 1 to 8; for csi and si, 
1. This must match the Machine-ID field of the 
Processor Channels screen.
1
Switch Number
Enter the nod e numb er of the switc h b eing  
ad ministered . If there is only one switc h, 
the value must b e 1
. This must matc h the 
Local Node Number field in the switch dial 
p lan.
1
IP Address/Host Name
Enter the IP address for the switch being 
administered.
192.168.1.124
TCP Port
Enter a TCP port number for each Intuity 
AUDIX for each switch being administered. 
This must match the Interface Channel field of 
the Processor Channels screen. You should use 
5002 for every switch linked over the LAN in 
a DCS network. Use the numbers6001-6999 
for gateway TCP links to remote switches in a 
DCS network. 
5002 
						

							Configuration 2: R7r (+CMS)  R7csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
98
Enable links and processor channels
You must enable links and processor channels before the connections can be used.
To enable a link, open its data module screen (ch da [ext]) and set the Enable 
Link? field to y. 
[note: to view a list of assigned data modules and their extensions, enter the “list 
data-module” command (l da)]
To enable the processor channels, open the processor channel screen (ch com p) 
and set the Enable field to y for each assigned processor channel.
Note:1. You must disable a link or processor channel before you can change its 
parameters.
Note:2. The busy-out command overrules the data module Enable Link? field.
Note:3. On the C-LAN boards, low-level connectivity can remain intact when 
higher-level applications such as DCS are not functioning. For example, 
an external ping to a C-LAN’s ethernet port could be successful even 
when the board is busied-out. When debugging connectivity problems, 
pinging only checks low-level connectivity. 
						

							Configuration 3:R8si R8r Gateway 
 R8si 
99
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Configuration 3:R8si R8r Gateway  R8si 
In this configuration, a DEFINITY ECS R8r acts as a gateway between two other 
nodes — one connected via X.25 to an R8si and the other via ethernet to another R8si.
Task Summary
The following tasks need to be completed for Switch 1, Switch 2, and Switch 3:
1  Review checklist
2  Switch 1 administration
 a  Assign node names
 b  Assign pdm data module
 c  Assign IP Interfaces
 d  Assign link (via an x.25 data module) to Switch 2
 e  Assign link (via an ethernet data module) to the LAN
 f  Assign processor channels
3  Switch 2 administration
 a  Assign link (via a proc-intf data module) to node 1
 b  Assign processor channels
4  Switch 3 administration
 a  Assign node names
 b  Assign IP Interfaces
 c  Assign link (via an ethernet data module) to the LAN
 d  Assign processor channels
5  Enable links and processor channels
DEFINITY
ECS R8r
BX.25Switch 1
DEFINITY ECS
Switch 3
DEFINITY ECS
Switch 2
R8si
Hub
Ethernet
R8si
C-LANC-LAN PI
PGATE
node-3 node-1
DS1
PDM 
						

							Configuration 3:R8si R8r Gateway 
 R8si 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
100
Prerequisite Administration
There are some system administration tasks that need to be completed before you can 
proceed with the connectivity administration described in this section.
Review the checklist of prerequisite administration tasks in Checklist for Prerequisite 
Administration  (page 54), before proceeding with the connectivity administration in 
this section.
SWITCH 2 SWITCH 1SWITCH 3
Configuration 3
DEFINITY ECS R7si DEFINITY ECS R7rDEFINITY ECS R7si
Processor
channelsProcessor
channelsProcessor
channelsInterface
channelsInterface
channelsInterface
channelsInterface
channels
1
2
2561
2
641
2
64 21
22
2321
22
2321
22
231
500
x(any)
x(any)
645001
2
31
32
256 1
5000
5003
6002
64500 1
21
22
23
31
32
384
Link 2 Link 5
Link 3Link 3
Gateway-tcp
hardware connections
Processor
UN331B
PGATE
TN577DS1
TN767/
TN464 DS1
TN767/
TN464
Digital
line
TN754
Processor bus Processor bus
TDM bus
RS232
Packet bus
10BaseT
ethernet
Processor
TN790B Processor
TN790B
Processor bus
TDM bus
TDM bus
Packet bus Packet bus
NetPkt
TN794 DS1
TN767/
TN464 DS1
TN767/
TN464 NetPkt
TN794PI
TN765
Voice
data
Voice
data
Network
control
UN332B
1
cydfec3a EWS 052099
Ext 4121 Ext 2102
loc 1c0102node-1
Ext 3391
loc 1b0117
192.168.10.1node-3
Ext 4351
loc 1a1017
192.168.10.3
1324
X.25
BX.25
DCP
MPDM
C-LAN
TN799
PktInt
TN1655
342C-LAN
TN799
software-defined connections