Lexmark X264 Service Manual

Diagnostic aids 3-29
7013-XXX
Min Copy Memory
This setting allocates the amount of DRAM memory to be used for storing copy jobs in the queue. 25, 35, 50, 80 
and 100 MB are the available settings. To adjust the minimum copy memory, perform the following steps:
1.In the configuration menu, scroll to the MinCopy Memory item, and press .
2.Use the  or  to increase or decrease the setting’s value.
3.When the desired value is displayed, press .
NumPad Job Assist
This setting determines if a user can configure...

3-30  Service Manual 7013-XXX
FB Edge Erase
This menu item sets the size, in millimeters, of the no print area around a flatbed scan job. Copy jobs will use the 
setting or two millimeters, whichever is larger.
To adjust the flatbed edge erase setting, perform the following steps:
1.In the Configuration menu, select the FB Edge Erase menu item.
2.Use the  or  to increase or decrease the setting’s value.
3.When the desired value is displayed, press .
Scanner Manual Registration
This item is used to...

Diagnostic aids 3-31
7013-XXX
16.Use the  or  to increase or decrease the setting’s value.
Note:  Each button press moves the margin values one pixel in the respective direction.
17.Press to accept the value.
18.Scroll to Top Edge, and press .
19.Use the  or  to increase or decrease the setting’s value.
Note:  Pressingmoves the margin up, and pressing moves the margin down.
20.Press to accept the value.
To manually register the flatbed, perform the following steps:
1.In the Configuration Menu, scroll to...

3-32  Service Manual 7013-XXX
Font Sharpening
This setting is used to set a text point size value below which the hig- frequency screens will be used when 
printing data. This setting affects only PCL, PostScript and PDF emulators.
Settings are in the range of 0–150 (24 is the default). For example, if the value is set to 24, then all fonts sized 24 
points or less use the high-frequency screens. 
To adjust the Font Sharpening setting, perform the following steps:
1.In the configuration menu, scroll to...

Diagnostic aids 3-33
7013-XXX
SE Menu
Note:  This is not the Fax SE menu. To enter the Fax SE menu, press **411 from the Ready screen.
Note:  This menu should be used as directed by second-level support.
Print SE Menus
General
Copyright - Displays copyright information.
Optra Forms mode - On or off
Code Revision Info
Network Code Level - Displays network code level
Network Compile Info - Displays compile information
Printer Code Level - Displays printer code information
Printer Compile Info - Displays...

3-34  Service Manual 7013-XXX
Paper jams
Avoiding jams
Most paper jams can be avoided by correctly loading paper and specialty media in the printer.
The following hints can help prevent paper jams:
•Use only the recommended print media.
•Do not overload the print media sources. Make sure the stack height does not exceed the maximum height 
indicated by the stack line on the labels in the sources.
•Do not load wrinkled, creased, damp, or curled print media.
•Flex, fan, and straighten print media before...

Diagnostic aids 3-35
7013-XXX
Understanding paper jam codes and locations
200-202 paper jams
1.Remove the paper tray from the printer.
2.If there is a paper jam, then remove the paper jam.
3.If there is not a paper jam, then open the front door, and remove the photoconductor kit and toner 
cartridge.
4.Lift the flap at the front of the printer, and remove any jammed sheets.
5.If there is not a paper jam at the front of the printer, then open the rear door, and remove the paper jam.
6.Close the rear door,...

3-36  Service Manual 7013-XXX
231 paper jam
1.Open the front door.
2.Open the rear door.
3.Remove the paper jam.
4.Close the rear door.
5.Close the front door, and press.
CAUTION
The fuser and the area inside of the printer near the fuser may be hot. Allow the surface to cool 
before removing media from this area. 

Diagnostic aids 3-37
7013-XXX
233 paper jam
1.Remove the paper tray from the printer.
2.Locate the lever shown, and pull it down to release and to remove the jammed sheets.
3.Reinstall the paper tray, and press.
234 paper jam
A single jam or multiple jams are in the duplex area of the printer when the printer is turned on. To locate and 
remove the jammed sheets, complete all steps in “231 paper jam” on page 3-36 and “233 paper jam” on 
page 3-37.
235 paper jam
1.Gently pull the jammed sheet out of the...

3-38  Service Manual 7013-XXX
242 paper jam
1.Remove the optional paper tray from the printer.
2.Remove the paper jam.
3.Reinstall the optional paper tray, and press.