Lexmark T656dne User Manual

Menu itemDescription
Duplex Binding
Long Edge
Short EdgeDefines the way duplexed pages are bound and how the printing on the back of the
page is oriented in relation to the printing on the front of the page
Notes:
Long Edge is the factory default setting.
Long Edge specifies that binding be placed on the left edge of portrait pages
and the top edge of landscape pages.
Short Edge specifies that binding be placed on the top edge of portrait pages
and the left edge of landscape pages.
Orientation
Auto
Long...

Menu itemDescription
Separator Sheets
None
Between Copies
Between Jobs
Between PagesSpecifies whether blank separator sheets are inserted
Notes:
None is the factory default setting.
Between Copies inserts a blank sheet between each copy of a print job if
Collation is set to On. If Collation is set to Off, then a blank page is inserted
between each set of printed pages, such as after all page 1s and after all page
2s.
Between Jobs inserts a blank sheet between print jobs.
Between Pages inserts a blank...

Menu itemDescription
Print Area
Normal
Whole PageSets the logical and physical printable area
Notes:
This menu does not appear if Edge to Edge is enabled in the
printer Setup menu.
Normal is the factory default setting. When attempting to
print data in the non‑printable area defined by the Normal
setting, the printer clips the image at the boundary.
The Whole Page setting allows the image to be moved into
the non‑printable area defined by the Normal setting, but
the printer will clip the image at the...

Menu itemDescription
Resource Save
On
OffSpecifies how the printer handles temporary downloads, such as
fonts and macros stored in RAM, when the printer receives a job
that requires more memory than is available
Notes:
Off is the factory default setting. Off sets the printer to retain
the downloads only until memory is needed. Downloads are
deleted in order to process print jobs.
The On setting retains the downloads during language
changes and printer resets. If the printer runs out of
memory, 38 Memory...

Menu itemDescription
Collate
Off (1,1,1,2,2,2)
On (1,2,1,2,1,2)Stacks the pages of a print job in sequence when printing multiple copies
Notes:
Off is the factory default setting. No pages will be collated.
The On setting stacks the print job sequentially.
Both settings print the entire job the number of times specified by the Copies
menu setting.
Separator Sheets
None
Between Copies
Between Jobs
Between PagesSpecifies whether blank separator sheets are inserted
Notes:
None is the factory default...

Menu itemDescription
N‑up Border
None
SolidPrints a border around each page image when using N‑up (pages‑sides)
Note: None is the factory default setting.
Staple Job
Off
OnSpecifies whether print jobs are stapled
Notes:
This menu item is available only when the StapleSmart Finisher is installed.
Off is the factory default setting. Print jobs are not stapled.
Envelopes are not stapled.
Offset Pages
Off
Between Jobs
Between CopiesStacks copies or print jobs into staggered sets in an output bin
Notes:
This...

Menu itemDescription
Enhance Fine Lines
On
OffEnables a print mode preferable for files such as architectural drawings, maps, electrical
circuit diagrams, and flow charts
Notes:
Off is the factory default setting.
To set Enhance Fine Lines using the Embedded Web Server, type the network
printer IP address in a browser window.
Gray Correction
Auto
OffAdjusts the gray value of printed output
Note: Auto is the factory default setting.
Brightness
‑6 to +6Adjusts or darkens printed output and conserves toner...

Menu itemDescription
Delete Downloads on Disk
Delete Now
Do Not DeleteRemoves downloads from the printer hard disk, including all held Jobs, buffered jobs,
and parked jobs. Job accounting information is not affected.
Note: Delete Now is the factory default setting.
Job Acct Stat
Print
ClearPrints a list of all stored job statistics or deletes the information from the printer hard
disk
Notes:
A printer hard disk must be installed in the printer and operating properly for
this menu item to be available....

PostScript menu
Menu itemDescription
Print PS Error
On
OffPrints a page containing the PostScript error
Note: Off is the factory default setting.
Font Priority
Resident
Flash/DiskEstablishes the font search order
Notes:
Resident is the factory default setting.
A formatted flash memory option card or printer hard disk must be
installed in the printer and operating properly for this menu item to be
available.
The flash memory option or printer hard disk cannot be Read/Write,
Write, or password protected....

Menu itemDescription
Symbol Set
10U PC‑8
12U PC‑850Specifies the symbol set for each font name
Notes:
10U PC‑8 is the US factory default setting.
12U PC‑850 is the international factory default setting.
A symbol set is a set of alphabetic and numeric characters, punctuation,
and special symbols. Symbol sets support the different languages or
specific programs such as math symbols for scientific text. Only the
supported symbol sets are shown.
PCL Emulation Settings
Point Size
1.00–1008.00Changes the point...