Lexmark E360dn User Manual

Menu itemDescription
Tray Renumber
Restore Defaults
Yes
NoReturns all tray, drawer, and feeder assignments to the factory default settings
Understanding printer menus
81
Downloaded From ManualsPrinter.com Manuals 

Maintaining the printer
Periodically, certain tasks are required to maintain optimum print quality.
Cleaning the exterior of the printer
1Make sure that the printer is turned off and unplugged from the wall outlet.
CAUTION—SHOCK HAZARD: To avoid the risk of electric shock when cleaning the exterior of the printer,
unplug the power cord from the wall outlet and disconnect all cables to the printer before proceeding.
2Remove all paper from the printer.
3Dampen a clean, lint‑free cloth with water....

Ordering supplies
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies
dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.com or contact the
place where you purchased the printer.
Note: All life estimates for printer supplies assume printing on letter‑ or A4‑size plain paper.
Ordering toner cartridges
When 88 Cartridge is Low appears or when the print becomes faded, you may be able to extend the life...

Ordering a photoconductor kit
Depending on your printer model, the printer issues a message or a light sequence to let you know the photoconductor
kit is near its end of life. At this time, order a photoconductor kit. You can also see the status of the photoconductor
kit by printing a network setup page.
Part namePart number
Photoconductor kit E260X22G
Replacing supplies
Replacing the toner cartridge
When 88 Cartridge is low appears, or when you experience faded print, remove the toner cartridge. Firmly...

3Unpack the new toner cartridge.
Warning—Potential Damage: When replacing a toner cartridge, do not leave the new cartridge exposed to
direct light for an extended period of time. Extended light exposure can cause print quality problems.
4Rotate the cartridge in all directions to distribute the toner.
5Install the new toner cartridge by aligning the rollers on the toner cartridge with the arrows on the tracks of the
photoconductor kit. Push the toner cartridge in as far as it will go. The cartridge...

1Turn the printer off.
2Open the front door by pressing the button on the left side of the printer and lowering the front door.
3Pull the photoconductor kit and toner cartridge out of the printer as a unit by pulling on the toner cartridge handle.
Note: The photoconductor kit and toner cartridge form a unit.
Place the unit on a flat, clean surface.
4Press the button on the base of the photoconductor kit. Pull the toner cartridge up and out using the handle.
Maintaining the printer
86
Downloaded From...

5Unpack the new photoconductor kit.
Warning—Potential Damage:  Be careful not to touch the photoconductor drum. Doing so may affect the print
quality of future print jobs.
6Insert the toner cartridge into the photoconductor kit by aligning the rollers on the toner cartridge with the tracks.
Push the toner cartridge until it clicks into place.
7Install the unit into the printer by aligning the arrows on the guides of the unit with the arrows in the printer. Push
the unit as far as it will go.
Maintaining...

8After you replace the photoconductor kit, reset the photoconductor counter.
To reset the photoconductor counter, open the front door, press and hold 
 until Resetting PC Counter
appears. The power light blinks, and the printer beeps.
Warning—Potential Damage: Resetting the photoconductor counter without replacing the photoconductor
may damage your printer and void your warranty.
9Close the front door.
Moving the printer
Before moving the printer
CAUTION—POTENTIAL INJURY: Before moving the printer,...

Administrative support
Finding advanced networking and administrator information
For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD and the
Embedded Web Server Administrators Guide on the Lexmark Web site at http://support.lexmark.com.
Using the Embedded Web Server
If the printer is installed on a network, the Embedded Web Server is available for a range of functions including:
Viewing a virtual display of the printer control panel
Checking the status of...

View the IP address on the printer control panel in the TCP/IP section under the Networks/Ports menu.
Print a network setup page or the menu settings pages and locate the IP address in the TCP/IP section.
2Click Device Status.
Viewing reports
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the
printer, the network, and supplies.
1Type the printer IP address into the address field of your Web browser.
Note: If you do not know the IP address of...