Lexicon Rv5 User Manual

RV-5Troubleshooting & Maintenance
6-7
RV-5 ERROR MESSAGES
RV-5 error messages are displayed on the OSD when certain error
conditions exist.  This section explains the meaning of these error
messages and how to fix each problem.
VIDEO ERROR MESSAGES
The following error messages apply specifically to video issues.
VIDEO PROCESS ERROR
This error message will display
when the incoming datastream is
at a higher resolution than the
resolution of the VIDEO OUT
parameter. The RV-5 can
up-sample a lower...

Troubleshooting & MaintenanceLexicon
6-8
CHANGE MONITOR 
MESSAGE
This error message flashes on the
2-line OSD and front panel
displays when an analog signal is
being sent to an HDMI monitor.
To correct the problem, change the video monitor setting to an
analog input source.
AUTOCAL ERROR MESSAGES
The following error messages apply specifically to error conditions
that exist during the AUTOCAL or SEMI AUTOCAL procedures, or
that pertain to the saved AUTOCAL settings.
MICROPHONE OVERLOAD 
ERROR
This error...

RV-5Troubleshooting & Maintenance
6-9
SUBWOOFER CAL ERROR
This error message will display
when the Subwoofer test has
failed.  Typically, this failure occurs
because the microphone is not in
the proper position or the volume
setting is too low.  
To correct the problem, check the
microphone position, verify the
subwoofer cables are connected
properly, verify that the volume
level is correct, and repeat the test.
Note: If you are using a powered subwoofer, verify that it is
powered on.
CROSS-OVER CHANGE...

Troubleshooting & MaintenanceLexicon
6-10
VIDEO RESOLUTIONS TABLE
The RV-5 Receiver is designed to allow flexibility in the selection of
video output resolutions.  However, there are restrictions on what
resolutions can be made available due to incoming signal
limitations.  
If you are not getting the expected resolution options for your
video monitor, it is possible that there is an incompatability
between the input setup selections and the incoming signal.  The
table below describes those formats that...

RV-5Troubleshooting & Maintenance
6-11
HDMI480i
BYPASS480i 480i** 480i** 480i** 1
480p 480p 480p** - - 1
720p 720p 720p** - - 1
1080i 1080i 1080i** - - 1
Component 
Analog480i 480i 480i - - 2, 3
480p 480p 480p - - 2, 3
720p 720p 720p - - 2, 3
1080i 1080i 1080i - - 2, 3
S-Video,     
Composite 
AnalogS-480i 480i 480i** 480i (from S) 480i (from S) 2, 3, 4
C-480i 480i 480i - 480i (from C) 2, 3, 4
S&C - 480i 480i 480i 480i (from S) 480i (from S) 2, 3, 4
HDMI480i
CONVERSION480i 480i** 480i 480i 1
480p 480p...

Troubleshooting & MaintenanceLexicon
6-12
ROUTINE MAINTENANCE
The bulleted items below describe routine maintenance that should
be performed on a periodic basis.
 Clean the RV-5 exterior surface with a soft, lint-free cloth. Do
not use alcohol, benzene, acetone-based cleaners or strong
commercial cleaners. Do not use a cloth made with steel wool
or metal polish. If the RV-5 is exposed to a dusty environment, a
low-pressure blower can be used to remove dust from its
exterior surface.
 Replace the remote...

A
Appendix
Specifications ............................................................................. A-2
Declaration of Conformity .......................................................... A-4
  

Appendix ALexicon
A-2
SPECIFICATIONS
Inputs
HDMI (Version 1.1) 2 HDMI Type A, 19-pin connectors
Analog Video 


Digital Audio 
(Toslink) connectors
nnectors conform to IEC-958, 
S/PDIF standards

Analog Audio 






Control 9-pin, D-sub connector


Input Voltage: 3V - 15V
Input Current: 10mA
Frequency: 20Hz - 1KHz
Accepts either stereo plug (Tip/Ring/Sleeve) or mono 
plug (Tip/Sleeve)
 HDMI Performance
HDMI Input Video: 480i/p, 576i/p, 720p, or 1080i
Audio: Dolby Digital, DTS, & PCM (32, 44.1, 48, 88.2,...

RV-5Appendix A
A-3
Component Video Performance
Compatibility 3-channel (Y, Pr, Pb), format-independent
Impedance 75Ω 
Insertion Loss 100MHz
Amplifier Outputs
Continuous Output 
Power85W per channel, 8Ω, all channels driven, 20Hz to 20kHz
Frequency Response 10Hz to 40kHz, +0, -2dB
THD + Noise 

Appendix ALexicon
A-4
*Depth measurement includes knobs, buttons, and terminal connections.
**For use with optional RF-1 Receiver.
Specifications are subject to change without notice.
General
Power Requirements 120V, 60Hz, 1300W, IEC detachable power cord (supplied) 
230V, 50Hz, 1300W, IEC detachable power cords (supplied 
for EU & UK) 
Power Consumption 4.82W at Power on, idle
1235W at rated power output (7-channels driven)
Dimensions  feet): 6.6 inches (168 mm)



Weight 

Rack-Mounting Lexicon built...