Lexicon Rv5 User Manual

RV-5Setup
3-5
SPEAKER/EQ SETUP
Select the SPEAKER/EQ SETUP menu to configure the Main Zone audio output connectors for the desired speaker setup. The Main Zone includes eight
audio output connectors labeled Front L/R, Center, Subwoofer, Side L/R and Rear L/R.
MANUAL
SPEAKERS
SPEAKER DISTANCES
OUTPUT LEVELS
SPEAKERS
AUTO SETTINGS: OFF
FRONT L/R: 80Hz
CENTER: 80Hz
SIDE L/R: 80Hz
REAR/Z2 L/R: 80Hz
SUB/LFE LPF: 80Hz
SUBWOOFERS: 1
SUB HPF: 20Hz
SUB MODE: NORMAL
PERFORMS FULL AUTOMATIC
CALIBRATION
PERFORMS...

SetupLexicon
3-6
REAR AMPREAR AMP, ZONE 2
Selects the REAR AMP parameter, which identifies how the rear
amplifier is utilized. The amplifier can drive the rear speakers in the
Main Zone or the Zone 2 speakers. 
To maintain 7.1-channel surround sound in the Main Zone while
using the Zone 2 outputs, the Rear/Zone2 speaker connectors or the
Rear Preamp outputs should be used for the Main Zone rear channels
while the Zone 2 OUT RCA connectors are used with a second
amplifier for the Zone 2 audio.
MANUAL...

RV-5Setup
3-7
FULL AUTOCAL
Selects the FULL AUTOCAL procedure, which automatically sets the
speaker distances, cross-over points, and output levels, as well as
performing system equalization adjustments. 
Note: The Full or Semi Autocal settings that are saved to the Preset
locations include the system equalization adjustment values. However,
even if the Auto EQ setting is active, the autocal settings for the system EQ
do NOT apply to certain high bit-rate incoming data streams, such as 176
kHz and 192...

SetupLexicon
3-8
The microphone should be held within two feet of the speaker baffle
as a test tone is sent to the speaker.
The Subwoofer test is done in two parts. The user is instructed to
hold the microphone to the left of the primary listening position and
then to the right of the primary listening position. Two test tones are
sent out to all connected subwoofers during each of the two test
phases. Two tones are sent to ensure that subwoofers with auto
power settings are active during the procedure....

RV-5Setup
3-9
MANUAL SPEAKER SETUP
Selecting the SETUP menu SPEAKER/EQ SETUP menu MANUAL option opens the MANUAL menu, which is used to manually set the speaker
distances, cross-over points, and output levels.
AUTO SETTINGSOFF, ON
Loads the values from the active preset into the speaker cross-over
points, distances, or output level parameters. The Speakers
(cross-over points), Speaker Distances, and Output Levels menus all
have an Auto Settings parameter.  All three are the same parameter,
but each...

SetupLexicon
3-10
SPEAKERS MENU
Selecting the MANUAL SETUP menu SPEAKERS option opens the
SPEAKERS menu, which assigns independent cross-over points for
each Main Zone audio output connector. Front cross-over selections
affect the Sub Mode parameter options. 
Manual Speaker Setup Considerations:
 Select the cross-over point closest to the -3dB low frequency
rating of the associated speakers. For example, set the FRONT
L/R parameter to the cross-over point closest to the -3dB
low-frequency rating of the...

RV-5Setup
3-11
REAR/Z2 L/RFULL, 40 to 120Hz, NONE
Allows the manual selection of a cross-over point for the Main Zone
audio output connectors labeled REAR/Z2 L/R. Available selections
include NONE, FULL, 120 Hz, 100 Hz, and 80 Hz to 40 Hz in 10 Hz
increments.
 Select FULL to send a full-range signal to the Rear/Zone2 L/R
speakers. Otherwise, select the cross-over point closest to the
-3dB low-frequency rating of the Rear/Zone2 L/R speakers.
 When the speaker setup does not include rear speakers, select...

SetupLexicon
3-12
The distances for each speaker - Front Left, Center, Front Right, Side
Right, Rear Right, Rear Left, Side Left, and Subwoofers - can be set
individually. 
Note: When the speaker distance for the Front Left speaker is adjusted
above 20.0 feet from the shortest speaker distance, all speaker distances
will move in conjunction from the 20.2-feet parameter point. When the
Front Left speaker is adjusted to 20.2 feet, all other speaker distances that
are set to 0 feet will now move to 0.2...

RV-5Setup
3-13
To activate the Test Tone:
1. Press the Menu or Select button to enter the Menu structure.
2. Select Setup from the Main menu.
3. Select Speaker/EQ Setup.
4. Select Manual.
5. Select Output Levels.
6. Press the remote control  and  arrows to highlight the Test 
To n e  p a r a m e t e r.
7. Press the remote control SELECT or  arrow button to select 
t h e  Te s t  To n e  p a r a m e t e r.
8. Press the remote control  arrow to select manual test tones.  
The Test Tone parameter...

SetupLexicon
3-14
INPUT SETUP
Selecting the SETUP menu INPUT SETUP option opens the INPUT SETUP menu, a two-screen menu which sets up the input type and name, the
digital and analog inputs for both audio and video, the listening mode, and other advanced input settings.
INPUT
Selects between the twelve different inputs available. The input
selected in this parameter identifies the input that is currently being
setup or modified. Inputs can be scrolled through and modified
without leaving the input setup...