Lenovo 3000 J Series Manual
Have a look at the manual Lenovo 3000 J Series Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 207 Lenovo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Diagnostic Error Code FRU/Action 015-036-XXX USB port Register error System board 015-040-XXX USB port IRQ failure 1. Run setup and check for conflicts 2. Flash the system. See “Flash update procedures” on page 207 3. System board 015-195-XXX USB port Test aborted by user Information only Re-start the test, if necessary 015-196-XXX USB port test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 015-197-XXX USB port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 015-198-XXX USB port test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 015-199-XXX USB port test failed, cause unknown 1. Go to “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 018-000-XXX PCI Card Test Passed No action 018-0XX-XXX PCI Card Failure 1. Riser card, if installed 2. System board 018-195-XXX PCI Card Test aborted by user 1. PCI card 2. Information only Re-start the test, if necessary 018-196-XXX PCI Card test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file Chapter 7. Symptom-to-FRU Index 65
Diagnostic Error Code FRU/Action 018-197-XXX PCI Card test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 018-198-XXX PCI Card test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 018-199-XXX PCI Card test failed, cause unknown 1. Go to “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 018-250-XXX PCI Card Services error 1. PCI card 2. Riser card, if installed 3. System board 020-000-XXX PCI Interface Test Passed No action 020-0XX-XXX PCI Interface error 1. PCI card 2. Riser card, if installed 3. System board 020-195-XXX PCI Test aborted by user Information only Re-start the test, if necessary 020-196-XXX PCI test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 020-197-XXX PCI test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 66 Lenovo 3000 J Series
Diagnostic Error Code FRU/Action 020-198-XXX PCI test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 020-199-XXX PCI test failed, cause unknown 1. Go to “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 020-262-XXX PCI system error 1. PCI card 2. Riser card, if installed 3. System board 025-000-XXX IDE interface Test Passed No action 025-00X-XXX 025-01X-XXX IDE interface failure 1. IDE signal cable 2. Check power supply voltages 3. Reseat IDE signal cable 4. IDE device 5. System board 025-027-XXX IDE interface Configuration/Setup error 1. IDE signal cable 2. Flash the system. See “Flash update procedures” on page 207 3. Reseat IDE signal cable 4. IDE device 5. System board 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure 1. IDE signal cable 2. Check power supply 3. Reseat IDE signal cable 4. IDE device 5. System board 025-195-XXX IDE interface Test aborted by user Information only Re-start the test, if necessary 025-196-XXX IDE interface test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 025-197-XXX IDE interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test Chapter 7. Symptom-to-FRU Index 67
Diagnostic Error Code FRU/Action 025-198-XXX IDE interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 025-199-XXX IDE interface test failed, cause unknown 1. Go to “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 030-000-XXX SCSI interface Test Passed No action 030-00X-XXX 030-01X-XXX SCSI interface failure 1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board 030-027-XXX SCSI interface Configuration/Setup error 1. SCSI signal cable 2. Flash the system. See “Flash update procedures” on page 207 3. SCSI device 4. SCSI adapter card, if installed 5. System board 030-03X-XXX 030-04X-XXX SCSI interface error 1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board 030-195-XXX SCSI interface Test aborted by user Information only Re-start the test, if necessary 030-196-XXX SCSI interface test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 030-197-XXX SCSI interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 68 Lenovo 3000 J Series
Diagnostic Error Code FRU/Action 030-198-XXX SCSI interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 030-199-XXX SCSI interface test failed, cause unknown 1. Go to “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 035-000-XXX RAID interface Test Passed No action 035-0XX-XXX RAID interface Failure 1. RAID signal cable 2. RAID device 3. RAID adapter card, if installed 4. System board 035-195-XXX RAID interface Test aborted by user Information only Re-start the test, if necessary 035-196-XXX RAID interface test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 035-197-XXX RAID interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 035-198-XXX RAID interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 035-199-XXX RAID interface test failed, cause unknown 1. See “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 071-000-XXX Audio port Interface Test Passed No action Chapter 7. Symptom-to-FRU Index 69
Diagnostic Error Code FRU/Action 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error 1. Run Setup 2. Flash the system. See “Flash update procedures” on page 207 3. System board 071-03X-XXX Audio port failure 1. Speakers 2. Microphone 3. Audio card, if installed 4. System board 071-04X-XXX Audio port failure 1. Run Setup 2. Audio card, if installed 3. System board 071-195-XXX Audio port Test aborted by user Information only Re-start the test, if necessary 071-196-XXX Audio port test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 071-197-XXX Audio port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 071-198-XXX Audio port test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 071-199-XXX Audio port test failed, cause unknown 1. See “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 071-25X-XXX Audio port failure 1. Speakers 2. Audio card, if installed 3. System board 080-000-XXX Game Port interface Test Passed No action 080-XXX-XXX Game Port interface Error 1. Remove the game port device and re-test the system 080-195-XXX Game Port interface Test aborted by user Information only Re-start the test, if necessary 70 Lenovo 3000 J Series
Diagnostic Error Code FRU/Action 080-196-XXX Game Port interface test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 080-197-XXX Game Port interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 080-198-XXX Game Port interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 080-199-XXX Game Port interface test failed, cause unknown 1. See “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 086-000-XXX Mouse Port interface Test Passed No action 086-001-XXX Mouse Port interface Presence 1. Mouse 2. System board 086-032-XXX Mouse Port interface Device controller failure 1. Mouse 2. System board 086-035-XXX Mouse Port interface Reset 1. Mouse 2. System board 086-040-XXX Mouse Port interface IRQ failure 1. Run Setup 2. Mouse 3. System board 086-195-XXX Mouse Port interface Test aborted by user Information only Re-start the test, if necessary 086-196-XXX Mouse Port interface test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file Chapter 7. Symptom-to-FRU Index 71
Diagnostic Error Code FRU/Action 086-197-XXX Mouse Port interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 086-198-XXX Mouse Port interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 086-199-XXX Mouse Port interface test failed, cause unknown 1. See “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 089-000-XXX Microprocessor Test Passed No action 089-XXX-XXX Microprocessor failure 1. Microprocessor(s) 2. System board 089-195-XXX Microprocessor Test aborted by user Information only Re-start the test, if necessary 089-196-XXX Microprocessor test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 089-197-XXX Microprocessor test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 089-198-XXX Microprocessor test aborted 1. Flash the system. See “Flash update procedures” on page 207 2. Go to “Undetermined problems” on page 81 089-199-XXX Microprocessor test failed, cause unknown 1. See “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 170-000-XXX Voltage Sensor(s) Test Passed No action 72 Lenovo 3000 J Series
Diagnostic Error Code FRU/Action 170-0XX-XXX Voltage Sensor(s) failure 1. Flash system 2. System board 170-195-XXX Voltage Sensor(s) Test aborted by user Information only Re-start the test, if necessary 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file 170-197-XXX Voltage Sensor(s) test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 170-198-XXX Voltage Sensor(s) test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 170-199-XXX Voltage Sensor(s) test failed, cause unknown 1. See “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error 1. Power supply 2. System board 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error 1. Voltage Regulator Module (VRM) 2. Microprocessor 3. System board 175-000-XXX Thermal Sensor(s) Test Passed No action 175-0XX-XXX Thermal Sensor(s) failure 1. Flash system 2. System board 175-195-XXX Thermal Sensor(s) Test aborted by user Information only Re-start the test, if necessary 175-196-XXX Thermal Sensor(s) test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file Chapter 7. Symptom-to-FRU Index 73
Diagnostic Error Code FRU/Action 175-197-XXX Thermal Sensor(s) test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 175-198-XXX Thermal Sensor(s) test aborted 1. If a component is called out, make sure it is connected and/or enabled 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Go to “Undetermined problems” on page 81 175-199-XXX Thermal Sensor(s) test failed, cause unknown 1. See “Undetermined problems” on page 81 2. Flash the system and re-test. See “Flash update procedures” on page 207 3. Replace component under function test 175-250-XXX 175-251-XXX Thermal Sensor(s) limit error 1. Check fans 2. Check Power supply voltages 3. Microprocessor 4. System board 185-000-XXX Asset Security Test Passed No action 185-XXX-XXX Asset Security failure 1. Flash system 2. System board 185-278-XXX Asset Security Chassis Intrusion 1. Assure Asset Security Enabled 2. C2 Cover Switch 3. System board 201-000-XXX System Memory Test Passed No action 201-XXX-XXX System Memory error 1. Replace the memory module called out by the test 2. System board 202-000-XXX System Cache Test Passed No action 202-XXX-XXX System Cache error 1. Cache, if removable 2. System board 3. Microprocessor 206-000-XXX Diskette Drive Test Passed No action 206-XXX-XXX Diskette Drive error 1. Diskette Drive Cable 2. Check power supply voltages 3. Diskette drive 4. System board 74 Lenovo 3000 J Series