Land Rover Range Rover Classic Workshop 1995 Rover Manual

19FUEL SYSTEM
22
REPAIR FUEL TANK
Service repair no - 19.55.01
WARNING: Ensure that fuel handling
precautions given in Section 01 -
introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system. Disconnect battery
negative lead.
2.Syphon fuel tank into a suitable...

MFI
23
REPAIR
13.Remove back two bolts and nut plates securing
fuel tank cradle.
14.Remove front nuts, bolts and washers. Remove
fuel tank cradle.
15.With assistance, tilt right hand side of tank
upwards and manoeuvre tank through chassis to
remove.
Refit
16.Reverse removal procedure. Ensuring sealing
ring, fuel pipe and hose connections are secure.
17.Run engine, check all connections for fuel leaks.FUEL FILLER FLAP RELEASE BUTTON
Service repair no - 19.55.23
On closing, filler flap will be locked...

19FUEL SYSTEM
24
REPAIR FUEL FILLER FLAP RELEASE ACTUATOR
Service repair no - 19.55.17
Remove
1.Release fuel filler flap. Disconnect the battery
negative lead.
2.Remove eight screws, with draw closure panel,
in right hand side of load space.
3.Release two screws and manoeuvre actuator
clear of its mounting.
4.Disconnect wiring plug.
5.Withdraw actuator.
Refit
6.Reverse removal procedure. 

MFI
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Air-Bypass valve (stepper motor) 20...............................................................
All flexible hose securing clamps 1,3...............................................................
Fuel feed pipe - hose to fuel rail 22.................................................................
Fuel filter...

MFI
1
SERVICE TOOLS FUEL SYSTEM
LRT-19-004 Test equipment fuel pressure
18G 500
LRT-19-003 MFI pressure test adaptor
LST 143
LRT-19-002 Connector splitter
LST 144
LRT-19-001 Fuel pump remover
LST 131 

CRUISE CONTROL - V8i
1
DESCRIPTION AND OPERATION CRUISE CONTROL SYSTEM-HELLA GR66
Description
The cruise control system consists of
electro-mechanical devices, and comprises of the
following components.
ELECTRONIC CONTROL UNIT (ECU)
The engine control module is located behind the lower
dash panel. The microprocessor based ECU
evaluates the signals provided by the driver controls,
brake pedal switch, clutch pedal switch on manual
models, and the vehicle speed sensor. The ECU
activates the vacuum pump as...

CRUISE CONTROL - V8i
1
FAULT DIAGNOSIS ROAD TEST
CAUTION: Do not engage cruise control
when vehicle is being used in low transfer
gear or reverse.
WARNING: The use of cruise control is not
recommended on winding, snow covered
or slippery roads or in heavy traffic
conditions where a constant speed cannot be
maintained.
1.Start engine, depress main control switch to
actuate cruise control system. Accelerate to
approximately 50 km/h, (30 mph), operate
set/accswitch, immediately release switch,
remove foot...

CRUISE CONTROL - V8i
1
REPAIR BRAKE AND CLUTCH PEDAL SWITCHES/VENT
VALVES
Service repair no - 19.75.34 - Clutch Switch
Service repair no - 19.75.35 - Brake Switch
Remove
1.Remove lower dash panel.
2.Disconnect electrical multi-plug from pedal
switch.
3.Pull vent hose from switch.
4.Release switch/vent valve from bracket.
Refit
5.Reverse removal procedure.
NOTE: The switch/vent valve is factory set
and does not require adjustment in
service.MAIN CONTROL SWITCH
Service repair no - 19.75.30
Switch...

19FUEL SYSTEM
2
REPAIR CRUISE CONTROL SWITCH
Service repair no - 19.75.36
Remove
1.Disconnect battery negative lead.
2. Models fitted with airbags:Remove drivers
airbag module.
See SUPPLEMENTARY
RESTRAINT SYSTEM, Repair, Drivers
Airbag Module
3. Models without airbags:Turn steering wheel
through 90Ê. Remove 2 Torx screws securing
pad to steering wheel and remove steering
wheel pad.
4.Disconnect cruise control switch multiplug from
main harness.
5.Disconnect 2 Lucars from horn contacts.
6.Remove 2 screws...

CRUISE CONTROL - V8i
3
REPAIR ROTARY COUPLER
Service repair no - 19.75.54
The rotary coupler is located behind the steering
wheel. Access is gained by removing the steering
wheel and steering column shroud.
NOTE: On vehicles fitted with airbags.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, Rotary Coupler
Remove
1.Disconnect battery negative lead.
2.Remove steering wheel.
See STEERING,
Repair, Steering Wheel
3.Release 2 turnbuckles securing lower dash
closing panel and lower.
4.Remove 3 screws securing...