Land Rover Range Rover Classic Workshop 1995 Rover Manual

19FUEL SYSTEM
12
REPAIR Throttle disc - inspect and overhaul
36.Examine throttle shaft for excessive wear
between bushes in plenum chamber and shaft.
A small amount of clearance is permissible. If
excessive wear is evident fit new shaft and
bushes as follows.
37.Remove two split screws securing throttle disc
and withdraw disc.
CAUTION: Take care not to damage shaft.
38.Remove shaft and air seal from plenum
chamber.
39.Using suitable drift, drive out bushes.
CAUTION: Take care not to damage
plenum chamber...

MFI
13
REPAIR 44.Grease new air seal with Admax L3 or
Energrease LS3. Push seal down shaft, into
counterbore until seal is 6.0 mm (0.236 in) below
face of plenum.
Throttle levers and bracket - assemble
45.Fit stop lever to throttle shaft, a new tab washer
and secure with throttle shaft nut.
46.Holding stop lever on stop, tighten throttle shaft
nut securely, bend over tabs to lock nut in
position.
47.Fit inboard throttle return spring noting that small
hooked end of spring is nearest plenum.
48.Locate...

19FUEL SYSTEM
14
REPAIR RAM HOUSING
Service repair no - 19.70.04
Remove
1.Disconnect battery negative lead.
2.Remove plenum chamber.
See Plenum
Chamber
3.Release hoses from ram housing.
4.Remove six through bolts (with plain washers)
securing ram housing to intake manifold.
5.Remove ram housing from intake manifold.
6.Place a protective cover over inlet bores to
prevent ingress of dirt.
Refit
7.Clean all mating faces.
8.Apply Hylomar sealant to intake manifold face.
9.Fit ram housing. Tighten bolts,...

MFI
15
REPAIR 11.Loosen clip and disconnect top hose from
thermostat housing.
12.Disconnect multiplug from distributor amplifier
module.
13.Loosen clip and disconnect hose from heater
valve.
14.Remove injector harnesses from behind fuel rail
and lay to one side.
15.Loosen union and disconnect fuel return hose
from fuel rail.
NOTE: The intake manifold can be
removed from the cylinder block without
removing the fuel rail and injectors.
16.Using the sequence shown, remove 12 bolts
securing the intake...

19FUEL SYSTEM
16
REPAIR Refit
1.Clean mating faces of cylinder heads, cylinder
block and intake manifold.
2.Locate NEW seals in position with ends
engaged in notches formed between the cylinder
heads and block.
3.Apply RTV sealant between ends of seals,
cylinder head and block.
4.Fit intake manifold gasket with the word
FRONTto the front and open bolts hole to the
front RH side.
5.Fit gasket clamps and tighten bolts finger tight.
6.Locate intake manifold onto cylinder heads,
clean threads of manifold...

MFI
17
REPAIR FUEL FILTER
Service repair no - 19.25.02
Remove
WARNING: Spilling of fuel is unavoidable
during this operation. Ensure all
necessary precautions are taken to
prevent fire and explosion.
WARNING: Ensure fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Access to filter is gained through right hand rear
wheel arch.
3.Clean area around hose connections to...

19FUEL SYSTEM
18
REPAIR FUEL PIPES
Service repair no - 19.40.92
WARNING: Depressurise fuel system.See
Depressurise Fuel System
before
disconnecting any fuel pipes ensure that
all necessary precautions are taken against fuel
spillage
WARNING: Ensure fuel handling
precautions given in Section 01 -
introduction are strictly adhered to when
carrying out following instructions.
KEY
1. Fuel feed hose to fuel rail.
2. Fuel return hose to fuel tank.
3. Rigid fuel feed pipe.
4. Rigid fuel return pipe.
5. Fuel...

MFI
19
REPAIR THROTTLE CABLE
Service repair no - 19.20.06
Remove
1.Remove clevis pin securing cable to lever.
2.Carefully pry throttle cable adjustment nut out of
mounting bracket.
3.Remove cable from mounting bracket.
4.Release outer cable from retaining clips in
engine compartment.
5.Remove lower dash panel.
6.Disconnect cable from accelerator pedal and
release cable locknut.
7.Feed cable through bulkhead grommet into
engine compartment.
Refit
8.Feed new cable from engine compartment
through bulkhead...

19FUEL SYSTEM
20
REPAIR ACCELERATOR PEDAL
Service repair no - 18.30.35
Remove
1.Remove lower dash panel.
2.Remove clevis pin securing throttle cable to
accelerator pedal.
3.Release tension from pedal return spring.
4.Remove circlip from pedal pivot pin.
5.Withdraw pivot pin.
NOTE: It may be necessary to lower
steering column to gain access to pivot
pin circlip.
6.Remove accelerator pedal.
Refit
7.Lightly grease pivot and clevis pins.
8.Fit clevis pin using aNEWcotter pin.
9.Reverse removal procedure.FUEL...

MFI
21
REPAIR 6.Remove access panel from floor.
7.Disconnect multi-plug from fuel sender unit.
8.Disconnect two fuel line unions from fuel pump.
9.Using service tool no. LRT-19-001, remove
pump unit retaining ring. Withdraw unit from fuel
tank.
WARNING: A quantity of fuel will be
retained in body of unit, care must be
taken to prevent fuel spillage when unit is
removed.
Refit
10.Insert fuel pump into tank. Fit retaining ring.
Tighten to
48 Nm.
11.Connect fuel lines to pump.
12.Connect multi-plug to...