Land Rover Freelander 2002my Electrical Library 3rd Edition Rover Manual

DESCRIPTION AND OPERATION
4.60FREELANDER 02MY
Reverse
When reverse gear is selected, a main relay feed is able to flow from the transmission 
selector/inhibit switch (C0244) to  the reverse lamp relay (C0935) on an NG wire. The 
reverse lamp relay (C0935) is earthed on a B wire and controls operation of the reverse 
lamps. For more information on reverse lamp operation, refer to the  Brake and Reverse 
Lamps  section of this manual.
 
+  BRAKE AND REVERSE LAMPS. 
A main relay feed is also supplied to the...

DESCRIPTION AND OPERATION
FREELANDER 02MY 4.61
4th Gear
To select fourth gear, only shift solenoid C is operated. The ATCU (C0932) will provide a 
feed to shift solenoid C (C0243) on an OU wire.
5th Gear
To select fifth gear, shift solenoid A and shift solenoid C are operated. The ATCU (C0932) 
will provide a feed to shift solenoid A (C0243) on an R wire. Shift solenoid C (C0243) 
receives a feed from the ATCU (C0932) on an OU wire.
4
When 4 is selected, a main relay feed is able to flow from the...

DESCRIPTION AND OPERATION
4.62FREELANDER 02MY
Manual (Steptronic) Mode
When in sport mode, if the selector lever is moved to the + or - positions, the gearbox will 
automatically enter manual (Steptronic) mode. When the selector lever is moved to the - 
position, it provides a feed to the ATCU (C0932) on a GK wire. When the selector lever is 
moved to the + position, it provides a feed to the ATCU (C0932) on a GB wire. Manual gear 
changes can now be performed sequentially using the selector lever....

DESCRIPTION AND OPERATION
FREELANDER 02MY 4.63
Torque Converter Lock-Up
When the gearbox is in 4th or 5th gear, and the ATCU registers a high vehicle speed 
combined with a small throttle angle, the ATCU will lock the torque converter. This will 
enable maximum power to be transmitted to the road wheels. When this occurs, the ATCU 
(C0932) provides a PWM signal to the Lock-Up solenoid (C0243) on a U wire. The solenoid 
(C0243) is earthed via the ATCU (C0932) on an SB wire. For more details on torque...

DESCRIPTION AND OPERATION
4.64FREELANDER 02MY
ELECTRONIC AUTOMATIC TRANSMISSION (EAT) – 02MY
DESCRIPTION
General
The Jatco 5–speed automatic transmission fitted to Freelander is controlled by an Automatic 
Transmission Control Unit (ATCU). The ATCU is located inside the engine E-box, and 
receives information from the following sources to calculate when to operate the solenoid 
valves contained within the gearbox to enable quick, smooth, quiet gear changes;

The Engine Control Module (ECM) via the...

DESCRIPTION AND OPERATION
FREELANDER 02MY 4.65
OPERATION
General
Feed from the positive battery terminal (C0192) is supplied to the main relay and fusible link 
3 (C0632) on an R wire. Both are located in the engine compartment fuse box.
The battery also provides a feed to fusible link 4 of the engine compartment fuse box 
(C0632) on vehicles fitted with an instrument dimmer switch. For more information, refer to 
the  Interior Lamps  section of this manual.
 
+  INTERIOR LAMPS. 
Operation of the main...

DESCRIPTION AND OPERATION
4.66FREELANDER 02MY
ATCU
The ATCU monitors the operation of the automatic gearbox via four sensors:

The temperature of the automatic transmission fluid (ATF) is measured by the fluid 
temperature sensor. The fluid temperature sensor (C0243) receives a feed from the 
ATCU (C0932) on a WK wire. The temperature sensor return (C0243) to the ATCU 
(C0932) is via a KB wire. As the temperature of the ATF rises, so the resistance of the 
sensor decreases. The ATCU registers this drop...

DESCRIPTION AND OPERATION
FREELANDER 02MY 4.67
Reverse
When reverse gear is selected, a main relay feed is able to flow from the transmission 
selector/inhibit switch (C0244) to  the reverse lamp relay (C0935) on an NG wire. The 
reverse lamp relay (C0935) is earthed on a B wire and controls operation of the reverse 
lamps. For more information on reverse lamp operation, refer to the  Brake and Reverse 
Lamps  section of this manual.
 
+  BRAKE AND REVERSE LAMPS. 
A main relay feed is also supplied to...

DESCRIPTION AND OPERATION
4.68FREELANDER 02MY
4th Gear
To select fourth gear, only shift solenoid C is operated. The ATCU (C0932) will provide a 
feed to shift solenoid C (C0243) on an OU wire.
5th Gear
To select fifth gear, shift solenoid A and shift solenoid C are operated. The ATCU (C0932) 
will provide a feed to shift solenoid A (C0243) on an R wire. Shift solenoid C (C0243) 
receives a feed from the ATCU (C0932) on an OU wire.
4
When 4 is selected, a main relay feed is able to flow from the...

DESCRIPTION AND OPERATION
FREELANDER 02MY 4.69
Manual (Steptronic) Mode
When in sport mode, if the selector lever is moved to the + or - positions, the gearbox will 
automatically enter manual (Steptronic) mode. When the selector lever is moved to the - 
position, it provides a feed to the ATCU (C0932) on a GK wire. When the selector lever is 
moved to the + position, it provides a feed to the ATCU (C0932) on a GB wire. Manual gear 
changes can now be performed sequentially using the selector lever....