Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual
Have a look at the manual Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
GENERAL SPECIFICATION DATA 3 INFORMATION FUEL SYSTEM Fuel lift pump type Mechanical with hand primer............................................................ Fuel lift pump pressure 42 - 55 Kgf/cm 2(3 - 4 lbf/in2) at 1800 rpm ..................................................... Fuel filter Paper element in disposable canister.......................................................................... Air cleaner Paper element type........................................................................ COOLING SYSTEM System type Pressurised, spill return, thermostatically controlled..................................................................... water and anti freeze mixture. Pump assisted thermo syphon. Coolant radiator combined with oil cooler and turbo intercooler. Cooling fan 11 blade axial flow 433 mm diameter, 1.29:1 drive....................................................................... ratio, with viscous coupling. Pump type Centrifugal, impellor, belt driven........................................................................ Thermostat opening 88°C ......................................................... Expansion tank cap pressure 1,06 Kgf/cm 2(15 Ibf/in2) (system pressure) ........................................... CLUTCH Type Valeo diaphragm spring................................................................................. Centre plate diameter 235 mm....................................................... Facing material Verto F202 grooved................................................................. Release bearing Ball journal............................................................... TRANSMISSION Main gearbox Type R380 Single helical constant mesh....................................................................... Speeds 5 forward, 1 reverse, all synchromesh............................................................................. Transfer box Type LT230 Two speed reduction on main gearbox output. Front...................................................................... and rear drive permanently engaged via a lockable differential Rear axle Type Spiral bevel, fully floating shafts................................................................................. Ratio 3.54:1.................................................................................
04GENERAL SPECIFICATION DATA 4 INFORMATIONREV: 05/99 Front axle Type Spiral bevel, enclosed constant velocity joints, fully................................................................................. floating shafts, 32°angularity of universal joint on full lock Ratio 3.54:1................................................................................. Propeller shafts Type, front and rear Tubular 51 mm dia........................................................... Universal joints Open type Hookes O3EHD................................................................. STEERING Power steering box Make/type Adwest Varamatic - worm and roller box........................................................................ Ratio Variable: straight ahead 19.3:1 on lock 14.3:1................................................................................. Steering wheel turns, lock-to-lock 3.375.................................... Steering pump Make/type Hobourn-Eaton series 500........................................................................ Steering geometry Steering wheel diameter 412 mm (16.22 in).................................................. Toe-out measurement 0 to 2 mm toe out...................................................... Toe-out included angle 0°to 0°20 ..................................................... Camber angle 0°* .................................................................. Castor angle 3°* ..................................................................... Swivel pin inclination static 7°* ............................................... * Check with vehicle on level ground, in unladen condition and five gallons of fuel. Rock the front of the vehicle up and down to allow it to take up a normal static position. Turning circle between kerbs 90 models: 265/75 x 16 tyres 12,65 m (41.5 ft).............................................................. All other tyres 11,70 m (38.4 ft)................................................................... 110 models: 750 x 16 tyres 13,41 m (44 ft).................................................................. 130 models: 750 x 16 tyres 15,24 m (50 ft)..................................................................
GENERAL SPECIFICATION DATA 5 INFORMATION SUSPENSION Type Coil springs controlled by telescopic dampers front................................................................................. and rear. Front Transverse location of axle by Panhard rod, and fore................................................................................. and aft location by two radius arms. Anti-roll bar fitted as standard on 90 models with 265/75 tyres and 130 models. Rear Fore and aft movement inhibited by two tubular trailing................................................................................. links. Lateral location of axle by a centrally positioned A frame, upperlink assembly, bolted at the apex to a ball joint mounting. Anti-roll bar fitted as standard on 90 models with 265/75 tyres, 110 models with self levelling unit, and 130 models. ROAD SPRING DATA 90 (2400 Kg) Part No. Colour Code Front - Drivers side NRC 9446 Blue/green Front - Passenger side NRC 9447 Blue/yellow Rear - Drivers side NRC 9448 Blue/red Rear - Passenger side NRC 9449 Yellow/white 90 (2550 Kg) Front - Drivers side NRC 9446 Blue/green Front - passenger side NRC 9447 Blue/yellow Rear - Drivers side NRC 9462 Green/yellow/red Rear - Passenger side NRC 9463 Green/yellow/white 110 (3050 Kg) Front - both sides NRC 8045 Yellow/yellow Rear - both sides NRC 6904 Red/green 110 Levelled (2950 Kg) Front - both sides NRC 8045 Yellow/yellow Rear - both sides NRC 7000 Green/white 110 (3400 Kg) Front - both sides NRC 8045 Yellow/yellow Rear - both sides NRC 6904 Red/green Rear helper springs - both sides RRC 3266 No colour code 110 (3600 Kg) Front - Drivers side NRC 9448 Blue/red Front - passenger side NRC 9449 Yellow/white Rear - both sides NRC 6904 Red/green Rear helper springs - both sides RRC 3226 No colour code 130 (3500 Kg) Front - drivers side NRC 9448 Blue/red Front - passenger side NRC 9449 Yellow/white Rear - drivers side NRC 6389 Red/red Rear - passenger side NRC 6904 Red/green Front/rear helper springs - both sides RRC 3266 No colour code
04GENERAL SPECIFICATION DATA 6 INFORMATION SHOCK ABSORBERS Type Telescopic, double-acting non-adjustable................................................................................. Bore diameter 35.47mm................................................................... BRAKES Front service brake Caliper AP Lockheed, four opposed pistons.............................................................................. Operation Hydraulic, self adjusting......................................................................... Disc 90 - Solid, outboard, 110/130 - Ventilated, outboard.................................................................................. Disc diameter 298 mm (11.73 in)................................................................... Disc thickness 90 - 14,1 mm (0.56in), 110/130 - 24mm (0.95 in).................................................................. Wear limit 1 mm (0.04in) per side of disc......................................................................... Disc run-out maximum 0,15mm (0.006 in)..................................................... Pad area 58 cm 2(9.0 in2) .......................................................................... Total swept area 801,3 cm2(124.2 in2) ............................................................... Pad material Ferodo 3440 non asbestos..................................................................... Pad minimum thickness 3 mm (0.12in)................................................... Rear service brake Caliper AP Lockheed opposed piston.............................................................................. Operation Hydraulic, self adjusting......................................................................... Disc Solid, outboard.................................................................................. Disc diameter 90 - 290 mm (11.42 in), 110/130 - 298 mm (11.73)................................................................... Disc thickness 90 - 12,5 mm (0.49 in), 110/130 - 14,1 mm (0.56 in).................................................................. Wear limit 90 - 0,38 mm (0.015 in), 110/130 - 1,0 mm (0.04 in)......................................................................... per side of disc Disc run-out maximum 0,15 mm (0.006 in)..................................................... Pad area 90 - 30,5 cm 2(4.37 in2), 110/130 - 36,2 cm2(5.61 in2) .......................................................................... Total swept area 90 - 694 cm2(106.98 in2) ............................................................... Pad material Ferodo 3440 non asbestos..................................................................... Pad minimum thickness 3 mm (0.12 in)................................................... Parking brake Type Mechanical, cable operated drum brake on the rear of................................................................................. the transfer gearbox output shaft Drum internal diameter 254 mm (10.0 in)..................................................... Width 70 mm (2.75 in)................................................................................ Pad material Ferodo 3611 non asbestos..................................................................... Servo/master cylinder Manufacturer Lucas.................................................................... Servo type LSC 80........................................................................ Master cylinder type 25,4 mm (1.0 in) diameter, tandem......................................................... Pressure reducing valve, failure conscious Cut-in pressure, 90 - 24 bar (360 Ibf/in 2) ratio 4.0:1, ...................... 110 - 43 bar (645 Ibf/in2) ratio 2.9:1* NOTE: * Pressure reducing valves are not fitted to all 110 specifications.
GENERAL SPECIFICATION DATA 7 INFORMATION AIR CONDITIONING System CFC free expansion valve system............................................................................. Compressor Sanden TRS105N..................................................................... Refrigerant R134a CFC free....................................................................... Charge quantity 1.1 Kg................................................................ WIPER MOTORS Tailgate wiper motor Make/type IMOS (non-serviceable)........................................................................ Running current, wet screen at 20°C ambient 1.0 to 2.8 amps................. Wiper speed, wet screen at 20°C ambient 37 to 43 cycles per minute....................... Windscreen wiper motor Make/type Lucas 14W uprated two speed........................................................................ Armature end float 0,1 to 0,2 mm............................................................ Brush length, minimum 4,8 mm.................................................... Brush spring tension 140 to 200 g........................................................ Resistance of armature winding at 16ÊC (69ÊF) measured between adjacent commutatator segments 0.23 to 0.35 ohms................................................... Light running, rack disconnected: current at 13.5 V 2.0 amps......... Wiper speed, wet screen, 60 seconds from cold Low speed - 45±3 rev/min, High speed - 65±5 .............. rev/min ELECTRICAL System 12 volt, negative ground............................................................................. Battery Make/type - standard Land Rover Parts and Equipment/Lucas maintenance....................................................... free 9-plate 072 Make/type - heavy duty Land Rover Parts and Equipment/Lucas maintenance.................................................... free 14-plate 663 Generator Manufacturer Magnetti Marelli.................................................................... Type A127 - 100amp................................................................................. Polarity Negative ground............................................................................. Brush length: New 17 mm......................................................................... Worn, minimum free protrusion from moulding 5 mm........ Brush spring pressure flush with moulding 1.3N to 2.7N...................... Regulator voltage 13.6 to 14.4 volts............................................................. Nominal output Generator speed 6000 rev/min..................................................... Control voltage 14 volt........................................................ Amp 65 amp.........................................................................
04GENERAL SPECIFICATION DATA 8 INFORMATION Fuses Type Autofuse (blade type) blow ratings to suit individual................................................................................. circuits Horns Make/type Mixo TR99........................................................................ Starter motor Make and type Bosch 12v................................................................. BULBS REPLACEMENT BULBS TYPE Headlamps 12V 60/55W Halogen Front side lamps 12V 5W bayonet Side repeater lamps 12V 5W capless Tail lamps 12V 5/21W bayonet Direction indicator lamps 12V 21W bayonet Number plate lamp 12V 5W capless Reverse lamp 12V 21W bayonet Rear fog guard lamp 12V 21W bayonet Interior roof lamps 12V 10W festoon Instrument illumination 12V 1.2W capless Warning light panel 12V 1.2W bulb/holder unit Hazard warning switch 12V 1.2W capless CAUTION: The fitting of new bulbs with wattages in excess of those specified will result in damage to vehicle wiring and switches.
GENERAL SPECIFICATION DATA 9 INFORMATION VEHICLE WEIGHTS AND PAYLOAD When loading a vehicle to its maximum (Gross Vehicle Weight), consideration must be taken of the unladen vehicle weight and the distribution of the payload to ensure that axle loadings do not exceed the permitted maximum values. It is the customers responsibility to limit the vehicles payload in an appropriate manner such that neither maximum axle loads nor Gross Vehicle Weight are exceeded. Maximum EEC kerb weight and distribution - all optional equipment VEHICLE AXLE WEIGHTS 90 models Standard High load Front axle 1200 Kg (2645 lb)......................................................................... 1200 Kg (2645 lb) Rear axle 1380 kg (3042 lb).......................................................................... 1500 Kg (3307 lb) Gross vehicle weight 2400 Kg (5291 lb)........................................................ 2550 Kg (5622 lb) 110 models Levelled Unlevelled Front axle 1200 Kg (2645 lb)......................................................................... 1200 Kg (2645 lb) Rear axle 1750 Kg (3858 lb).......................................................................... 1850 Kg (4078 lb) Gross vehicle weight 2950 Kg (6503 lb)........................................................ 3050 Kg (6724 lb) 130 models Front axle 1580 Kg (3483 lb)......................................................................... Rear axle 2200 Kg (4850 lb).......................................................................... Gross vehicle weight 3500 Kg (7716 lb)........................................................ NOTE: Axle weights are not accumulative. The individual maximum axle weights and gross vehicle weight must not be exceeded. EEC VEHICLE KERB WEIGHTS 90 models Standard High load Soft top: 1695 Kg (3736 lb)............................................................................ 1699 Kg (3745 lb) Pick-up: 1694 Kg (3734 lb)............................................................................ 1698 Kg (3743 lb) Hard top: 1746 Kg (3849 lb).......................................................................... 1750 Kg (3858 lb) Station wagon: 1793 Kg (3952 lb)................................................................. 1797 Kg (3961 lb) 110 models Soft top: 1872 Kg (4127 lb)............................................................................ 1882 Kg (4149 lb) Pick-up: 1880 Kg (4144 lb)............................................................................ 1890 Kg (4166 lb) High capacity pick-up: 1917 Kg (4226 lb)...................................................... 1927 Kg (4248 lb) Hard top: 1913 Kg (4217 lb).......................................................................... 1923 Kg (4239 lb) Station wagon: 2018 Kg (4448 lb)................................................................. 2028 Kg (4470 lb) County station wagon: 2054 Kg (4528 lb)...................................................... 2064 Kg (4550 lb) 130 models Crew cab and High capacity pick-up: 2086 Kg (4598 lb)............................... EEC kerb weight = Unladen weight + Full fuel tank + 75 Kg (165 lb).
04GENERAL SPECIFICATION DATA 10 INFORMATION TOWING WEIGHTS On-road Off-road Unbraked trailers 750 Kg (1653 lb).............................................................. 500 Kg (1102 lb) Trailers with overrun brakes 3500 Kg (7716 lb)............................................. 1000 Kg (2204 lb) 4 wheel trailers with coupled brakes * 4000 Kg (8818 lb).............................. 1000 Kg (2204 lb) NOTE: * Only applies to vehicles modified to accept coupled brakes. NOTE: All weight figures are subject to local restrictions. OFF-ROAD PERFORMANCE 90 models Max. gradient (EEC kerb weight) 45° ..................................... Approach angle: Soft top and Pick-up (EEC kerb weight) 48° .................. Hard top and station wagon (EEC kerb weight) 51.5° ...... Departure angle Soft top and Pick-up (EEC kerb weight) 49° .................. Hard top and Station wagon (EEC kerb weight) 53° ............... Wading depth 500 mm (20 in)................................................................... Min. ground clearance (unladen): Soft top and pick-up 191 mm (7.5 in)................................................. Hard top and station wagon 229 mm (9.0 in)..................................... NOTE: Departure angles do not account for the addition of a tow hitch. 110 and 130 models Max. gradient (EEC kerb weight) 45° ..................................... Approach angle (EEC kerb weight) 50° .................................. Departure angle (EEC kerb weight) 110 models 35° ...................................................................... 130 models 34° ...................................................................... Wading depth 500 mm (20 in)................................................................... Min. ground clearance (unladen 215 mm (8.5 in)....................................... NOTE: Departure angles do not account for the addition of a tow hitch.
GENERAL SPECIFICATION DATA 11 INFORMATION REV: 05/99 TYRE SIZE AND PRESSURES 90 models Front Rear Normal - all load conditions 205 R16 radial & 265/75 R16 (multi-terrain)1,9 bar .................................. 2,4 bar 28 Ibf/in 235 Ibf/in2 2,0 kgf/cm22,5 kgf/cm2 750 R16 radial1,9 bar ........................................................ 2,75 bar 28 Ibf/in240 Ibf/in2 2,0 kgf/cm22,8 kgf/cm2 110 models Normal - all load conditions 750 R16 Radial1,9 bar ....................................................... 3,3 bar 28 Ibf/in 248 Ibf/in2 2,0 kgf/cm23,4 kgf/cm2 130 models Normal - all load conditions 750 R16 Radial3,0 bar ....................................................... 4,5 bar 44 Ibf/in 265 Ibf/in2 3,1 kgf/cm24,6 kgf/cm2 WARNING: Tyre pressures must be checked with the tyres cold, as the pressure is about 0,21 bar (3 Ibf/in 2, 0,2 kgf/cm2) higher at running temperature. If the vehicle has been parked in the sun or high ambient temperatures, DO NOT reduce the tyre pressures, move the vehicle into the shade and wait for the tyres to cool before checking the pressures. WHEELS 90 models Steel wheel size: Heavy duty - UK and Western Europe 6.5F X 16............................. Other markets 5.5F X 16.................................................................. Alloy wheel size 7J X 16................................................................ 110 models Steel wheel size: Heavy duty - UK and Western Europe 6.5F X 16............................. Other markets 5.5F X 16.................................................................. 130 models Steel wheel size: Heavy duty - UK and Western Europe 6.5F X 16............................. Other markets 5.5F X 16.................................................................. WARNING: Always use the same make and type of radial-ply tyres, front and rear. DO NOT use cross-ply tyres, or interchange tyres from front to rear. ·If the the wheel is marked TUBED, an inner tube MUST be fitted, even with a tubeless tyre. ·If the wheel is marked TUBELESS, an inner tube must NOT be fitted.
04GENERAL SPECIFICATION DATA 12 INFORMATION VEHICLE DIMENSIONS 90 models Overall length: Soft top and Pick-up 3722 mm (146.5 in)................................................ Hard top and Station wagon 3883 mm (152.9 in).................................... Overall width: 1790 mm (70.5 in)................................................................... Overall height: Soft top 1965 mm (77.4 in).................................................................... Pick-up and Station wagon 1963 mm (77.3 in)...................................... Hard top 1972 mm (77.6 in)................................................................... Wheelbase 2360 mm (92.9 in)....................................................................... Track front/rear 1486 mm (58.5 in)................................................................. Width between wheel boxes 925 mm (36.4 in)............................................ 110 models Overall length: Soft top and Pick-up 4438 mm (175 in)................................................ High capacity pick-up 4631 mm (182 in).............................................. Hard top/Station and County 4599 mm (181 in)................................... Overall width: 1790 mm (70.5 in)................................................................... Overall height: 2035 mm (80.1 in).................................................................. Wheelbase 2794 mm (110 in)....................................................................... Track front/rear 1486 mm (58.5 in)................................................................. Width between wheel boxes: High capacity pick-up 1090 mm (43 in).............................................. all other models 925 mm (36.4 in)....................................................... 130 models Overall length 5132 mm (202 in)................................................................... Overall width 1790 mm (70.5 in).................................................................... Overall height 2035 mm (80.1 in)................................................................... Wheelbase 3226 mm (127 in)....................................................................... Track front/rear 1486 mm (58.5 in)................................................................. Width between wheel boxes 1090 mm (43 in)............................................