Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual

82AIR CONDITIONING
6
ADJUSTMENT SYSTEM TEST
1.Place the vehicle in a ventilated, shaded area
free from excessive draught, with the doors and
windows open.
2.Check that the surface of the condenser is not
restricted with dirt, leaves, flies, etc. Do not
neglect to check the surface between the
condenser and the radiator. Clean as necessary.
3.Switch on the ignition and the air conditioner air
flow control. Check that the blower is operating
efficiently at low, medium and high speeds.
Switch off the blower...

AIR CONDITIONING
7
ADJUSTMENT 11.All precautions must be taken to prevent
damage to fittings and connections. Slight
damage could cause a leak with the high
pressures used in the system.
12.Always use two wrenches of the correct size,
one on each fitting when releasing and
tightening refrigeration unions.
13.Joints and O rings should be coated with
refrigeration oil to aid correct seating. Fittings
which are not lubricated with refrigerant oil are
almost certain to leak.
14.All lines must be free of...

AIR CONDITIONING
1
REPAIR COMPRESSOR
Service repair no - 82.10.20
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
3.Remove compressor drive belt.See
Compressor drive belt
4.Disconnect high pressure pipe from compressor.
5.Disconnect low pressure pipe from compressor.
6.Remove O ring from each flange.
7.Disconnect compressor clutch harness
multi-plug.
8.Remove compressor from mounting bracket
studs.Refit
9.If a...

82AIR CONDITIONING
2
REPAIR COMPRESSOR DRIVE BELT
Service repair no - 82.10.02
Remove
1.Disconnect battery.
2.Remove auxiliary drive belt
See ELECTRICAL,
Repair, Auxiliary drive belt.
3.Remove 3 nuts securing drive belt guard to
compressor retaining studs.
4.Slacken 3 belt tensioner retaining bolts.
5.Remove compressor drive belt. Mark direction
on belt if refitting.Refit
6.Fit compressor drive belt.
7.Fit drive belt guard.
8.Fit torque meter to centre of tensioner, apply and
hold a torque of
35 Nm (26...

AIR CONDITIONING
3
REPAIR CONDENSER FAN AND MOTORS
Service repair no - 82.15.08
Remove
1.Disconnect battery.
2.Remove 6 screws and lift grille panel from
vehicle.
3.Disconnect fan motor multi-plugs and release
harness retaining clips.
4.Remove nut and washers and withdraw fan
blade from motor drive shaft.
5.Remove 2 retaining screws, release motor fan
from shroud support brackets and feed motor
multi-plug lead through appropriate aperture.
Refit
6.Feed motor lead through fan shroud.
7.Fit motor to fan...

82AIR CONDITIONING
4
REPAIR
8.Remove 4 bolts and large packing washers
securing fan cowling brackets to wing sides.
9.Remove 4 nuts securing fan cowling to lower
mounting bracket and lift complete assembly
from condenser.
10.Remove 2 bolts securing bonnet striker support
plate and cross braces to grille top panel.
11.Remove 2 bolts securing cross braces to front
wings.
12.Lift condenser, from bottom mounting lugs and
carefully ease forwards to clear top grille panel.
13.Lift condenser, complete with...

AIR CONDITIONING
5
REPAIR RECEIVER/DRIER
Service repair no - 82.17.01
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
3.Remove 6 screws and lift grille panel from
vehicle.
4.Disconnect receiver/drier dual pressure switch
multi-plug.
5.Disconnect high pressure pipe at receiver/drier.
6.Disconnect bottom union at condenser.
7.Remove retaining bolts and open clamps.
8.Release receiver/drier from condenser and...

82AIR CONDITIONING
6
REPAIR 9.Remove plug connector from resistor.
10.Remove relay from connecting block to gain
access to fixing screw.
11.Remove screw and release relay connector
block. Retain relay in connector block.
12.Remove screw and detach air conditioning 30
amp fuse bracket from resistor. Refit both
resistor retaining screws.
13.Using suitable pipe clamps, clamp heater matrix
feed and return hoses at base of heater/cooler
unit. Release retaining clips and remove hoses.
14.From inside vehicle...

AIR CONDITIONING
7
REPAIR EVAPORATOR - LH DRIVE
Service repair no - 82.25.20
Remove
1.Remove heater/cooler unit
See Heater/cooler
unit.
2.Suitably support unit on a bench to prevent
damage to heater matrix pipes.
3.Release 3 nuts and remove mounting bracket
from underneath unit casing.
4.Remove 7 screws securing outlet duct to
heater/cooler unit.
5.Carefully break sealing compound around edge
of duct and pull ducting from unit.
6.Remove 15 screws located around cover seam.
Break sealing compound from...

82AIR CONDITIONING
8
REPAIR
13.Remove all other fixings securing evaporator
and heater matrix support frame to unit casing.
14.Lift evaporator and heater matrices, complete
with support frame assembly, clear of casing.
Retain heater matrix pipe seal pad.
15.Remove 4 screws securing evaporator matrix to
support frame.
16.Withdraw evaporator matrix, complete with
expansion valve, from support frame.
17.Clean sealing compound from all joints of main
casing, top cover and outlet duct.
NOTE: The evaporator...