Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual

WIPERS AND WASHERS
1
REPAIR WIPER MOTOR AND DRIVE RACK
Service repair no - 84.15.09
Remove
1.Disconnect battery.
2.Remove wiper arms.
NOTE: Operations 3 - 5 are for RH drive
vehicles only.
3.Prise Land Rover decal from grab handle and
remove screw.
4.Remove lower screw and lift handle from fascia.
5.Remove screw fixing finisher to wiper motor
cover.
6.Remove door check strap cover, remove 3
screws and withdraw wiper motor cover. If
applicable, disconnect switch multi-plugs and/or
radio speaker leads....

84WIPERS AND WASHERS
2
REPAIR 16.Fully tighten tube nut and fit rubber sleeve.
17.Reconnect earth lead and multi-plug.
18.Before fitting cover and grab handle, fit wiper
blades. Reconnect battery and test operation of
wiper motor and drive assembly. If necessary,
adjust position of wiper blades.
19.Fit wiper motor cover and door check strap
cover.
20.On RH drive vehicles, fit finisher and grab
handle. 

WIPERS AND WASHERS
3
REPAIR WIPER MOTOR AND DRIVE RACK - VEHICLE
WITH AIR CONDITIONING, LH DRIVE
Service repair no - 84.15.20
Remove
1.Disconnect battery.
2.Remove wiper arms.
3.Remove single screw and remove fascia side
panel.
4.Remove 5 screws and withdraw instrument
panel as far as possible without straining wires
and cables.
5.Remove steering wheel
See STEERING,
Repair, Steering wheel.
6.Remove 2 screws at RH side and single screw
at LH side, inside instrument cowel, and
withdraw air conditioning...

84WIPERS AND WASHERS
4
REPAIR
9.Remove door check strap cover and 3 screws
and withdraw wiper motor cover. If applicable,
disconnect switch multi-plugs and/or radio
speaker leads.
10.Disconnect wiper motor multi-plug.
11.Disconnect earth lead. (Not applicable on later
models)
12.Lift rubber sleeve from wiper motor and slacken
wiper motor to drive tube nut.
13.Remove 2 screws and release wiper motor
retaining strap, complete with mounting pad and
earth tag.
14.Pull wiper motor and drive rack clear of...

WIPERS AND WASHERS
5
REPAIR WINDSCREEN WIPER ARMS
Service repair no - 84.15.01
Remove
1.Pull wiper arm away from windscreen.
2.Using a small screwdriver, hold back spring clip
which retains arm to spindle adaptor.
3.Pull wiper arm from splined adaptor.
Refit
4.Switch wiper motor to park position, with grub
screw retaining adaptor, uppermost.
5.Push arm on to adaptor so that wiper blade is
just clear of windscreen surround rubber.
6.Operate wipers and, if necessary, adjust position
of arms.WINDSCREEN...

84WIPERS AND WASHERS
6
REPAIR WINDSCREEN WIPER WHEEL BOXES - NON AIR
CONDITIONED VEHICLES
Service repair no - 84.15.25
Remove
1.Disconnect battery.
2.Remove wiper arms
See Windscreen wiper
arms.
3.Remove wiper motorSee Wiper motor and
drive rack - vehicle with air conditioning, LH
drive
.
4.Remove instrument housing, fascia crash pad,
and ventilator grille panel.
5.Slacken steering column support rod lower
fixing.6.Remove steering column upper support fixing.
7.Slacken nuts to release back plates from LH...

WIPERS AND WASHERS
7
REPAIR Refit
NOTE: During reassembly all fixings
related to wiper motor and wheelboxes are
finger tightened only, until all components
are correctly aligned.
12.Fit wheelboxes to bulkhead and secure with
retaining nuts and washers.
13.Fit drive rack tubes to wheelboxes.
14.Apply grease to drive rack and wheelboxes.
15.Align wiper motor and mounting pad, secure with
retaining strap and tighten drive tube nut.
16.Fully tighten wheelbox back plate nuts.
17.Fully tighten both wheelbox...

84WIPERS AND WASHERS
8
REPAIR WINDSCREEN WIPER WHEELBOXES - AIR
CONDITIONED VEHICLES
Service repair no - 84.15.25/20
Remove
1.Disconnect battery.
2.Remove wiper motor and drive rack
See Wiper
motor and drive rack - air conditioned
vehicles.
3.Remove centre and LH fascia top crash rail
support bracket fixings.
4.Remove both demister vents from ducts.
5.Remove RH demister vent hose from duct.
6.Remove RH vent demister vent fixing and pivot
vent and hose aside.
7.Remove demister vent top duct.8.Release...

WIPERS AND WASHERS
9
REPAIR 13.Fit wheelboxes to bulkhead.
14.Fit drive tubes to wheelboxes.
15.Feed drive rack through tubes until fully seated
in both wheelboxes.
16.Secure drive tube nut to wiper motor.
17.Fit wiper motor strap and earth lead.
18.When all components are correctly aligned, fully
tighten wheelboxes nuts to secure drive tubes.
Tighten wheelbox to bulkhead nuts.
19.Fully tighten drive tube nut to wiper motor and
motor strap screws.
20.Connect multiplug to wiper motor and earth lead
to...

84WIPERS AND WASHERS
10
REPAIR Refit
8.Locate wiper motor drive spindle through
aperture in rear door.
9.Position wiper motor mounting bracket and
secure to rear door. Tighten bolt to
23 Nm (17
lbf/ft).
10.Reconnect harness multi-plug.
11.Secure drive spindle to door.
12.Fit wiper motor cover.
13.Fit rear wiper arm.
14.Fit spare wheel. Tighten retaining nuts to
130Nm
(96 lbf/ft).