Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual

AIR CONDITIONING
9
REPAIR EXPANSION VALVE - LH DRIVE
Service repair no - 82.25.01
Remove
1.Remove heater/cooler unit
See Heater/cooler
unit.
2.Suitably support unit on a bench to prevent
damage to heater matrix pipes.
3.Remove 7 screws securing outlet duct to
heater/cooler unit.
4.Break sealing compound around edge of duct
and pull duct from unit.
5.Remove all fixing screws securing top cover
seam and cover sides to main casing.
6.Remove 4 screws and 4 nuts from top of cover.
7.Break sealing compound...

82AIR CONDITIONING
10
REPAIR HEATER MATRIX - LH DRIVE
Service repair no - 82.25.19
Remove
1.Remove evaporator
See Evaporator.
2.Leaving evaporator in place, remove single
screw securing heater matrix pipe plate to base
of support frame.
3.Remove heater matrix and insulation pad.
Refit
4.Position insulation pad and fit heater matrix to
support frame.
5.Fit heater matrix and evaporator assembly
See
Evaporator.
BLOWER MOTOR ASSEMBLY- LH DRIVE
Service repair no - 82.25.14
Remove
1.Remove heater/cooler unit...

AIR CONDITIONING
11
REPAIR
9.Remove screw securing blower motor mounting
bracket to side of casing.
10.Remove nut and washer securing blower motor
housing to pedestal mounting bracket.
11.Lift blower motor assembly from casing.
12.Remove 3 screws and withdraw blower motor
and impellor from housing. Note position of side
mounting bracket and spacing washers between
motor mounting and housing.
13.Remove star washer and withdraw impeller from
blower motor.
14.Lift motor from plastic mounting.
15.Slacken...

82AIR CONDITIONING
12
REPAIR BLOWER MOTOR ASSEMBLY - RH DRIVE
Service repair no - 82.25.14
Remove
1.Disconnect blower motor wiring plugs.
2.Remove 2 screws securing blower motor cover
to main casing.
3.Withdraw cover sufficiently to release motor
Lucar connector and earth eylet. Remove cover.
4.Remove 6 screws and withdraw blower motor
and impeller.
5.Remove retaining nut and washer and withdraw
impeller from blower motor shaft.Refit
6.Secure impeller on new blower motor.
7.Fit blower motor assembly in...

AIR CONDITIONING
13
REPAIR HEATER/COOLER UNIT - RH DRIVE
Service repair no - 82.25.21
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Refrigerant recovery, recycling,
recharging.
3.Release ties, remove insulation cover and
disconnect evaporator low pressure pipe.
4.Disconnect evaporator high pressure pipe.
5.Discard all pipe connection O rings. Cap or plug
all connections to prevent ingress of dirt and
moisture.
6.Using suitable pipe clamps, clamp heater matrix
feed...

82AIR CONDITIONING
14
REPAIR Refit
19.Coat unions, threads and new O rings with
refrigerant oil prior to reassembly.
20.Position heater/cooler unit in engine
compartment and locate with air duct seal.
21.Secure unit top and bottom mounting brackets to
bulkhead and support bracket to front of unit
casing. Fully tighten fixing bolts when unit is
correctly positioned.
22.If applicable, fit blower motor resistor block to
vehicle wing.
23.Connect blower motor wiring plugs.
24.Fit footwell insulation and...

AIR CONDITIONING
15
REPAIR EVAPORATOR - RH DRIVE
Service repair no - 82.25.20
Remove
1.Remove heater/cooler unit
See Heater/cooler
unit - RH drive.
2.Suitably support unit on a bench.
3.Remove sealant and release thermostat probe
from low pressure pipe.
4.Remove 2 screws securing blower motor cover
to main casing.
5.Withdraw cover sufficiently to release motor
Lucar connector and earth eyelet. Remove
cover.
6.Unscrew top adaptor pipe from heater matrix.
7.Remove 18 fixings securing top cover to main...

82AIR CONDITIONING
16
REPAIR EXPANSION VALVE - RH DRIVE
Service repair no - 82.25.01
Remove
1.Remove evaporator
See Evaporator - RH
drive.
2.Unscrew union securing pressure sensor to low
pressure pipe.
3.Release spring clip securing temperature sensor
to low pressure pipe.
4.Unscrew union and remove expansion valve
from evaporator high pressure pipe.
5.Remove high pressure pipe from expansion
valve.
6.Discard all pipe connection O rings.
Refit
7.Coat unions, threads and new O rings with
refrigerant oil...

AIR CONDITIONING
17
REPAIR HEATER MATRIX - RH DRIVE
Service repair no - 82.25.19
Remove
1.Remove heater/cooler unit
See Heater/cooler
unit - RH drive.
2.Suitably support unit on a bench.
3.Remove sealant and release thermostat probe
from low pressure pipe.
4.Remove 2 screws securing blower motor cover
to main casing.
5.Withdraw cover sufficiently to release motor
Lucar connector and earth eyelet. Remove
cover.
6.Unscrew top adaptor pipe from heater matrix.
7.Remove 18 fixings securing top cover to main...

82AIR CONDITIONING
18
REPAIR RESISTOR, BLOWER MOTOR - LH DRIVE
Service repair no - 82.20.26
Remove
1.Remove multi-plug from resistor.
2.Remove blower motor relay from connecting
block to gain access to fixing screw.
3.Remove screw and release relay connector
block. Retain relay in connector block.
4.Remove screw and detach air conditioning 30
amp fuse bracket from resistor.
5.Lift resistor unit from top cover.
Refit
6.Locate resistor unit in top cover.
7.Fit fuse bracket.
8.Fit blower motor relay...