Land Rover Body And Paint Air Bag And Safety Belt Rover Manual
Have a look at the manual Land Rover Body And Paint Air Bag And Safety Belt Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ActionReasonOther WarningsMessage NoneVehicle body has become trapped on an obstacle. Alternates with next message. Do not jack the vehicle with the engine running. The suspension will enter extended mode and the message will appear. One chimeSUSPENSION IN EXTENDED MODE NoneReselect height if door is open or press switch to exit extended mode. NoneRESET SUSPENSION HEIGHT IF CLEAR OF OBSTACLE NoneCrawl (locked access) mode selected. NoneSUSPENSION LOCKED AT ACCESS HEIGHT NoneAccess height selected.NoneSUSPENSION ACCESS HEIGHT SELECTED NoneNormal height selected.NoneSUSPENSION NORMAL HEIGHT SELECTED NoneOff road height selected.NoneSUSPENSION OFF ROAD HEIGHT SELECTED NoneAir suspension remote control function is being operated. Continuous chime while height is changing. SUSPENSION REMOTE KEY OPERATION Close all doorsAir suspension height change is prevented because a door is open. One chimeSUSPENSION CLOSE DOOR TO CHANGE HEIGHT NoneA height change has been requested but is prevented because speed is too high. One chimeSUSPENSION SPEED TOO HIGH TO CHANGE HEIGHT Connect T4A fault has been detected in the air suspension system. System may still operate normally. Two chimes, amber indicator permanently illu- minated. SUSPENSION FAULT Information and Message CenterLesson 2 – Electrical 89Technical Training (G421249)
ActionReasonOther WarningsMessage Start engineVehicle height can only be raised with the engine running. One chimeSUSPENSION START ENGINE TO RAISE VEHICLE Place key in ignition to charge Handset battery lowNoneKEY BATTERY LOW PLACE IN IGNITION TO CHARGE Connect T4 to diagnose fault ACE system (if fitted) no longer available. Vehicle is still driveable. Amber indicator lamp will be permanently illu- minated SUSPENSION FAULT VEHICLE LEAN WHEN CORNERING Connect T4 to diagnose fault Major component failure, stop vehicle immediately. The red indicator lamp will flash accompanied by a chime SUSPENSION FAULT STOP SAFELY STOP ENGINE NoneMemory system - confirmation that selection is completed Double chime when selection complete MEMORY 1 SELECTED NoneMemory system - confirmation that selection is completed Double chime when selection complete MEMORY 2 SELECTED NoneMemory system - confirmation that selection is completed Double chime when selection complete MEMORY 3 SELECTED NoneMemory system - confirmation that memory has stored driver informa- tion Single chimeMEMORY 1 STORED NoneMemory system - confirmation that memory has stored driver informa- tion Single chimeMEMORY 2 STORED NoneMemory system - confirmation that memory has stored driver informa- tion Single chimeMEMORY 3 STORED NoneMemory system - confirmation that memory has stored driver informa- tion Single chimeDOOR MIRROR DIP STORED (G421249) Technical Training90 Lesson 2 – ElectricalInformation and Message Center
ActionReasonOther WarningsMessage To reselect press DSC switch System not available due to DSC switched off by driver. Amber indicator permanently illu- minated DSC SWITCHED OFF Connect T4 to diagnose fault System fault, drive with care and do not attempt to descend steep slopes. One chimeHDC FAULT SYSTEM NOT AVAILABLE Wait until message is deleted before attempting descent HDC switched off while brake system is cooling Green indicator flashing HDC TEMPORARILY NOT AVAILABLE SYSTEM COOLING NoneHDC unavailable, speed threshold exceeded (Max HDC operating speed is 31 mph (50 km/h), max speed for HDC selection is 50 mph (80 km/h)). Green indicator flashing HDC NOT AVAILABLE SPEED TOO HIGH NoneHDC inoperative because of incor- rect gear selection. (HDC operates in 1st and reverse on manual trans- missions and CommandShift™ 1st, R and D on automatic transmis- sions in high range. (In low range, HDC operates in all gears for manual and automatic transmis- sions). Green indicator flashing HDC NOT AVAILABLE IN THIS GEAR NoneHDC switched off by driver, Terrain Response system or speed threshold. One chime (if deselected by Terrain Response system or 50 mph (80 km/h) speed threshold exceeded) HDC SWITCHED OFF Tighten or replace cap. Check system for leaks NAS Only - DMTL pump unable to pressurise system NoneFUEL TANK CAP LOOSE OR MISSING Connect T4 to diagnose fault ECM has detected a fault in the engine management system MIL illuminatedENGINE SYSTEM FAULT Information and Message CenterLesson 2 – Electrical 91Technical Training (G421249)
ActionReasonOther WarningsMessage NoneIdle speed increased to assist engine cooling NoneHIGH ENGINE SPEED FOR COOLING Connect T4 to diagnose fault Advises driver that automatic transmission has a fault and performance may be affected NoneTRANSMISSION FAULT LIMITED GEARS AVAILABLE Connect T4 to diagnose fault Advises driver that automatic transmission has a fault NoneTRANSMISSION FAULT Connect T4 to diagnose fault Advises driver that fault has occurred and transmission temper- ature is too high. NoneTRANSMISSION FAULT AND OVERHEAT Check transmission for faults Advises driver that transmission temperature is too high. slow down or stop to assist cooling. NoneTRANSMISSION OVERHEAT SLOW DOWN NoneAdvises driver that reverse gear has been selected - Japanese market vehicles only NoneREVERSE GEAR SELECTED NoneAdvises driver that transfer box is in low range. One chime. Low range indicator flashes when range change is in progress. Indicator is permanently illu- minated when range change is complete LOW RANGE SELECTED NoneAdvises driver that transfer box has engaged high range. One chime. Low range indicator lamp is extin- guished. HIGH RANGE SELECTED Reduce speed to 40 km/h on automatic transmission and 20 km/h on manual transmission Driver has requested range change when vehicle speed is too high. One chimeSPEED TOO HIGH FOR RANGE CHANGE (G421249) Technical Training92 Lesson 2 – ElectricalInformation and Message Center
ActionReasonOther WarningsMessage NoneAlerts driver that range change will not occur until neutral is selected on the transmission. One chimeSELECT NEUTRAL FOR RANGE CHANGE Connect T4 to diagnose fault Automatic transmission park lock function ineffective due to transfer box being out of high or low range. Transfer box control module stopped transmitting on the CAN bus or while in neutral mode. One chime per second for 3 seconds. PARK LOCK FAILURE APPLY HANDBRAKE (PARK BRAKE - NAS models only) NoneRear differential temperature has reached or is approaching the overheat threshold. One chimeTRANSMISSION OVERHEAT SLOW DOWN Connect T4 to diagnose fault Fault has occurred which is preventing transfer box range change NoneTRANSMISSION RANGE CHANGE NOT AVAILABLE Connect T4 to diagnose fault Transfer box control module has stopped transmitting CAN bus messages. Defaults to open center differential. Message also displayed when fault occurs with electronic rear differen- tial One chimeTRANSMISSION FAULT TRACTION REDUCED Connect T4 to diagnose fault Fault has occurred with electronic rear differential. Stop vehicle at earliest opportunity NoneTRANSMISSION FAULT STOP SAFELY NoneDriver has disabled the adaptive cruise control system NoneCRUISE CONTROL CANCELLED NoneAdvisory message, pressure in a running tire decreased to first warning threshold. NoneCHECK ALL TYRE PRESSURES Inflate tyres to correct pressure Check tyre pressuresChimes emitted for a short time, amber indicator illumin- ated TYRE PRESSURES TOO HIGH Information and Message CenterLesson 2 – Electrical 93Technical Training (G421249)
ActionReasonOther WarningsMessage Inflate tyres to correct pressure Check tyre pressuresChimes emitted for a short time, amber indicator illumin- ated TYRE PRESSURES VERY LOW Inflate tires to correct pres- sure Pressure in a running tire decreased to warning threshold. Chimes emitted for a short time, amber indicator illumin- ated. FRONT LEFT TYRE PRESSURE VERY LOW Inflate tires to correct pres- sure Pressure in a running tire decreased to warning threshold. Chimes emitted for a short time, amber indicator illumin- ated. FRONT RIGHT TYRE PRESSURE VERY LOW Inflate tires to correct pres- sure Pressure in a running tire decreased to warning threshold. Chimes emitted for a short time, amber indicator illumin- ated. REAR LEFT TYRE PRESSURE VERY LOW Inflate tires to correct pres- sure Pressure in a running tire decreased to warning threshold. Chimes emitted for a short time, amber indicator illumin- ated. REAR RIGHT TYRE PRESSURE VERY LOW Inflate tires to correct pres- sure Pressure in a running tire too high threshold reached. NoneFRONT LEFT TYRE PRESSURE TOO HIGH Inflate tires to correct pres- sure Pressure in a running tire too high threshold reached. NoneFRONT RIGHT TYRE PRESSURE TOO HIGH Inflate tires to correct pres- sure Pressure in a running tire too high threshold reached. NoneREAR LEFT TYRE PRESSURE TOO HIGH Inflate tires to correct pres- sure Pressure in a running tire too high threshold reached. NoneREAR RIGHT TYRE PRESSURE TOO HIGH (G421249) Technical Training94 Lesson 2 – ElectricalInformation and Message Center
ActionReasonOther WarningsMessage Connect T4 to diagnose fault TPMS fault has occurred. Use diagnostics to check for correct system functionality. Chimes emitted for a short time, amber indicator perman- ently illuminated. Chimes emitted and amber indic- ator permanently illuminated at subsequent ignition on cycles. TYRE PRESSURE MONITORING SYSTEM FAULT NoneTPMS system set by driver for heavy load operation. No instrument cluster indicator illumination. TPMS switch status LED illumin- ated. TYRE PRESSURE MONITORING SET FOR HEAVY LOAD NoneNormal setting for TPMS.NoneTYRE PRESSURE MONITORING SET FOR LIGHT LOAD Inflate tires to correct pres- sure Pressure in spare tire decreased to warning threshold. NoneCHECK SPARE TYRE PRESSURE Connect T4 to diagnose fault Possible loss of RF transmission or defective sensor battery. Chimes emitted for a short time, amber indicator perman- ently illuminated. Chimes emitted and amber indic- ator permanently illuminated at subsequent ignition on cycles. FRONT LEFT TYRE PRESSURE NOT MONITORED Information and Message CenterLesson 2 – Electrical 95Technical Training (G421249)
ActionReasonOther WarningsMessage Connect T4 to diagnose fault Possible loss of RF transmission or defective sensor battery. Chimes emitted for a short time, amber indicator perman- ently illuminated. Chimes emitted and amber indic- ator permanently illuminated at subsequent ignition on cycles. FRONT RIGHT TYRE PRESSURE NOT MONITORED Connect T4 to diagnose fault Possible loss of RF transmission or defective sensor battery. Chimes emitted for a short time, amber indicator perman- ently illuminated. Chimes emitted and amber indic- ator permanently illuminated at subsequent ignition on cycles. REAR LEFT TYRE PRESSURE NOT MONITORED Connect T4 to diagnose fault Possible loss of RF transmission or defective sensor battery. Chimes emitted for a short time, amber indicator perman- ently illuminated. Chimes emitted and amber indic- ator permanently illuminated at subsequent ignition on cycles. REAR RIGHT TYRE PRESSURE NOT MONITORED The vehicle cannot be parked by the park brake system in the normal way until the ignition key is removed and a park brake switch apply request is made Loss of CAN or vehicle speed signal is missing Park brake amber indicator illumin- ates and red indic- ator flashes PARK BRAKE FAULT TO HOLD VEHICLE REMOVE KEY THEN APPLY PARK BRAKE (G421249) Technical Training96 Lesson 2 – ElectricalInformation and Message Center
ActionReasonOther WarningsMessage Connect T4 to diagnose fault Possible motor fault when driver requested a switch application Park brake red indicator flashes PARK BRAKE FAULT SYSTEM NOT FUNCTIONAL Follow bedding-in procedure in Service Procedures manual The park brake bedding cycle has been initiated by the dealer techni- cian Park brake red indicator flashes PARK BRAKE BEDDING CYCLE ACTIVE Do not use the park brake system when the vehicle is moving, except in an emergency The park brake is applied when the vehicle is moving Park brake red lamp permanently illuminated CAUTION! PARK BRAKE APPLIED Follow message instructionPossible system malfunction detected Park brake amber indicator perman- ently illuminates PARK BRAKE FAULT Follow message instructionPark brake system release is inhib- ited until footbrake is pressed NonePRESS FOOT BRAKE AND PARK BRAKE SWITCH TO RELEASE Follow message instructionPark brake system release is prevented until foot brake or clutch pedal is pressed NonePRESS FOOT BRAKE OR CLUTCH AND PARK BRAKE SWITCH TO RELEASE Use park brake switch and foot brake to release Drive away release function is not operating Park brake amber indicator perman- ently illuminated PARK BRAKE FAULT AUTO RELEASE NOT FUNCTIONAL Pull park brake switch to re-engage emergency release An emergency release operation has been detected Park brake red indicator flashes PARK BRAKE OFF LIFT SWITCH TO APPLY Add water and additive mixture to washer bottle Washer fluid quantity below 1 litreSingle chime at ignition on. LOW WASHER FLUID NoneDriver has selected headlamp feature by turning ignition off before turning off headlamps NoneHEADLAMP OFF DELAY XX SEC Information and Message CenterLesson 2 – Electrical 97Technical Training (G421249)
ActionReasonOther WarningsMessage Check coolant system for leaks and top up to correct levels Coolant level in header tank below recommended level NoneLOW COOLANT LEVEL NoneDrivers door open or not fully closed NoneDRIVERS DOOR OPEN NoneLeft rear door open or not fully closed NoneLEFT REAR DOOR OPEN NoneFront passenger door open or not fully closed NoneFRONT PASSENGER DOOR OPEN NoneRight rear door open or not fully closed NoneRIGHT REAR DOOR OPEN NoneTailgate open or not fully closedNoneTAILGATE OPEN NoneBonnet open or not fully closedNoneBONNET OPEN Use the steering wheel switches to view and change the settings menus or press the trip computer button to exit the setting menu Driver has accessed the Customer Settings menu NoneSETTINGS NoneDriver has selected the interior lamps off NoneINTERIOR LIGHT OFF NoneDriver has enabled the interior lamps NoneAUTOMATIC MODE Ambient Temperature The external ambient air temperature is measured by a sensor located on the right hand side of the bonnet locking platform, behind the front grill. The sensor is connected to the HEVAC module. The HEVAC module outputs temperature messages on the CAN bus which are used by the instrument cluster to display the current ambient temperature. The message center displays the ambient temperature in the top right hand corner of the LCD display. The temperature is displayed until the message center is required to display system information. When system information has been displayed, the ambient temperature will reappear. The temperature is displayed in ºF or ºC depending the market configuration of the vehicle. The driver can also change the temperature reading using the Customer Settings function. Cold Warning Indication (G421249) Technical Training98 Lesson 2 – ElectricalInformation and Message Center