Kyocera KM 8030 User Manual

Preparing to Copy
2-15
4Select the paper type.
5Press [Close].
6Press [Close]. The touch panel will return to the [Basic] screen.
Syst em Menu / Counter
Custom
Custom
Custom
Custom
Transp-
BondPrepunc hed Color Recycled
VellumPlain
RoughLabels C ards tock
Preprinted
LetterheadThick
Env elope
HighCustom 1
Custom 2
Custom 3
Custom 4Back Selec t Paper T ype
arenc ypaper
Qualit y
Downloaded From ManualsPrinter.com Manuals 

Preparing to Copy
2-16
Loading Originals
Loading Originals in the Document Processor
The document processor automatically scans each sheet of multiple originals individually. Both 
sides of two-sided originals are scanned automatically. 
The document processor supports the following types of originals.
Precautions on Types of Originals for Document Processor
Do not use the document processor for the following types of originals. In addition, if originals have 
punched holes or perforations, load them...

Preparing to Copy
2-17
1Adjust the original width guides to fit the originals.
2Place the originals. Put the side to be copied (or the 
first side of two-sided originals) face-up. Slide the 
leading edge into the document processor as far as it 
will go.
IMPORTANT: Confirm that the original width guides 
exactly fits the originals. If there is a gap, readjust the 
original width guides. The gap may cause the originals 
to jam.
Pull out the ejection guide for originals of 8
1/2×14 
(B4) or 11 × 17 (A3)....

Preparing to Copy
2-18
Loading Originals on the Platen
To copy books, magazines, or other originals that cannot be loaded in the document processor, 
open the document processor and place the original directly on the platen.
Adjust how the document processor opens by using 
the document processor angle adjustment lever. Move 
the lever left to open the document processor 60° and 
move it right to open the document processor 30°.
IMPORTANT: Before opening the document 
processor, be sure that there are no...

Preparing to Copy
2-19
Metric models
3Close the document processor. For originals over 4 cm thick, leave the document processor open 
during copying.
IMPORTANT: Do not push the document processor forcefully when you close it. Excessive 
pressure may crack the platen glass. 
Shadows may be copied around the edges and in the middle of open-faced originals such as books.
Caution
Do not leave the document processor open as there is a danger of personal injury.
Downloaded From ManualsPrinter.com Manuals 

Preparing to Copy
2-20
Selecting the Language
Select the language displayed on the touch panel. 
The following languages are available.
1Press the System Menu/Counter key.
2Press [Language].
3Press the key for the desired language. 
The touch panel language will change 
accordingly. Languages
Inch models English, French (Francais), Spanish (Español) and Japanese ( )
Metric models English, German (Deutsch), French (Français), Spanish (Español) and 
Italian (Italiano)
System Menu / Counter
Job Sy stem...

3-1
3 Basic Operation
This chapter explains the following operations.
• Basic Copying Procedures...3-2
• Selecting Image Quality...3-4
• Adjusting Exposure...3-5
• Reducing/Enlarging...3-6
• Duplex Mode...3-11
• Split Mode...3-14
• Sort Mode...3-16
• Interrupt Mode...3-17
• Job Reservation...3-18
• Low-Power Mode...3-19
• Sleep Mode...3-20
Refer to the Advanced Operation Guide for additional functions.
Downloaded From ManualsPrinter.com Manuals 

Basic Operation
3-2
Basic Copying Procedures
Follow the steps as below for basic copying.
1Open the main power switch cover and move the main 
power switch to on (| position). 
After the copier has warmed up, the Start indicator will 
turn green.
2Place the originals in the document processor or on the 
platen.
NOTE: For loading instructions, refer to Loading 
Originals on page2-16.
3Check that [APS] is selected. In this 
mode, paper that matches the size of the 
originals will be selected automatically....

Basic Operation
3-3
NOTE: You can adjust the angle of the operation panel 
as shown by releasing the operation panel lock lever. 
After adjustment, lock the lever again. 
When adjusting the angle of the operation panel, do 
not place your hands or fingers underneath the 
operation panel. This can result in injury.
6Remove the finished copies from the output tray.
The output tray can hold up to 250 sheets of standard 
paper (80 g/m²). However, the capacity will vary 
depending on the type and condition of...

Basic Operation
3-4
Selecting Image Quality
Choose the image quality suited to the type of original.
1Place the originals in the document processor or on the platen.
2Press [Function].
3Press [Orig.Image Quality] ([Image 
Quality]).
4Select the image quality.
5Press the Start key to start copying.
NOTE: You can also adjust the exposure for each 
Image Quality mode. Refer to Chapter 3 of the 
Advanced Operation Guide. Image Quality Mode Description
Text+Photo For originals with both text and photographs....