Kyocera KM 8030 User Manual

							Preparing to Copy
2-15
4Select the paper type.
5Press [Close].
6Press [Close]. The touch panel will return to the [Basic] screen.
Syst em Menu / Counter
Custom
Custom
Custom
Custom
Transp-
BondPrepunc hed Color Recycled
VellumPlain
RoughLabels C ards tock
Preprinted
LetterheadThick
Env elope
HighCustom 1
Custom 2
Custom 3
Custom 4Back Selec t Paper T ype
arenc ypaper
Qualit y
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-16
Loading Originals
Loading Originals in the Document Processor
The document processor automatically scans each sheet of multiple originals individually. Both 
sides of two-sided originals are scanned automatically. 
The document processor supports the following types of originals.
Precautions on Types of Originals for Document Processor
Do not use the document processor for the following types of originals. In addition, if originals have 
punched holes or perforations, load them with the holes or perforations away from the leading edge.
• Transparencies such as for overhead projectors
• Delicate originals such as carbon paper, crumpled paper, or vinyl sheets
• Irregularly shaped (non-rectangular) originals, wet originals, or originals containing adhesive 
tape or glue
• Originals bound with clips or staples. (To avoid jams, remove the clips or staples and straighten 
any curls, wrinkles, or creases before loading them. Failure to do so may cause the originals to 
jam.) 
• Originals with cut-out sections or with very slippery surfaces
• Originals with correction fluid which is not dried
• Originals with folds. (To avoid jams, straighten the folds before loading them. Failure to do so 
may cause the originals to jam.)
How to Load Originals
Follow these steps to load originals in the document processor.
IMPORTANT: Before loading originals, be sure there 
are no originals left on the original eject table. Originals 
left on the original eject table may cause the new 
originals to jam.
Items Specifications
Weight 45 g/m² to 160 g/m²
Size Minimum: 5
1/2×8 1/2 (A5R); Maximum: 11 × 17 (A3)
Capacity Standard paper (80 g/m²), colored paper or recycled paper: 200 sheets 
(30 sheets in Auto Selection mode) 
Coated paper: 1 sheet 
High quality paper, 50 g/m²: 200 sheets 
High quality paper, 110 g/m²: 145 sheets
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-17
1Adjust the original width guides to fit the originals.
2Place the originals. Put the side to be copied (or the 
first side of two-sided originals) face-up. Slide the 
leading edge into the document processor as far as it 
will go.
IMPORTANT: Confirm that the original width guides 
exactly fits the originals. If there is a gap, readjust the 
original width guides. The gap may cause the originals 
to jam.
Pull out the ejection guide for originals of 8
1/2×14 
(B4) or 11 × 17 (A3).
Ensure that loaded originals do not exceed the level 
indicated. Exceeding the maximum level may cause 
the originals to jam.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-18
Loading Originals on the Platen
To copy books, magazines, or other originals that cannot be loaded in the document processor, 
open the document processor and place the original directly on the platen.
Adjust how the document processor opens by using 
the document processor angle adjustment lever. Move 
the lever left to open the document processor 60° and 
move it right to open the document processor 30°.
IMPORTANT: Before opening the document 
processor, be sure that there are no originals left on 
the original table or on the original eject table. 
Originals left on the original table or on the original 
eject table may fall off the copier when the document 
processor is opened. 
Do not move the document processor angle 
adjustment lever when the document processor is 
open. Close the document processor before using the 
lever.
1Open the document processor.
2Place the original. Put the copying side facedown and 
align it flush against the original size indicator plates 
with the back left corner as the reference point.
Inch models
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-19
Metric models
3Close the document processor. For originals over 4 cm thick, leave the document processor open 
during copying.
IMPORTANT: Do not push the document processor forcefully when you close it. Excessive 
pressure may crack the platen glass. 
Shadows may be copied around the edges and in the middle of open-faced originals such as books.
Caution
Do not leave the document processor open as there is a danger of personal injury.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-20
Selecting the Language
Select the language displayed on the touch panel. 
The following languages are available.
1Press the System Menu/Counter key.
2Press [Language].
3Press the key for the desired language. 
The touch panel language will change 
accordingly. Languages
Inch models English, French (Francais), Spanish (Español) and Japanese ( )
Metric models English, German (Deutsch), French (Français), Spanish (Español) and 
Italian (Italiano)
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pri nt L anguage
MP  tr a y
Or i g. Si ze Re g i s te r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAccounti ng
Sy s t em  M enuL anguage
Englis hFranc aisEs pañ ol
Downloaded From ManualsPrinter.com Manuals 
						

							3-1
3 Basic Operation
This chapter explains the following operations.
• Basic Copying Procedures...3-2
• Selecting Image Quality...3-4
• Adjusting Exposure...3-5
• Reducing/Enlarging...3-6
• Duplex Mode...3-11
• Split Mode...3-14
• Sort Mode...3-16
• Interrupt Mode...3-17
• Job Reservation...3-18
• Low-Power Mode...3-19
• Sleep Mode...3-20
Refer to the Advanced Operation Guide for additional functions.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Operation
3-2
Basic Copying Procedures
Follow the steps as below for basic copying.
1Open the main power switch cover and move the main 
power switch to on (| position). 
After the copier has warmed up, the Start indicator will 
turn green.
2Place the originals in the document processor or on the 
platen.
NOTE: For loading instructions, refer to Loading 
Originals on page2-16.
3Check that [APS] is selected. In this 
mode, paper that matches the size of the 
originals will be selected automatically. 
To change the paper size, press the 
desired paper size to select the paper 
source.
NOTE: For details on selecting paper 
manually, refer to Chapter 3 of the 
Advanced Operation Guide.
4Use the numeric keys to enter the copy quantity. You 
can specify up to 9,999 copies.
NOTE: It is possible to restrict the maximum copy 
quantity. Refer to Chapter 3 of the Advanced 
Operation Guide.
5Press the Start key to start copy.
Ready to copy.11x8½Paper  Si ze
Progr am Functi on User choice
Ba si c 11x8½
Pl ai n
11x8½
Re cy cl e d
11x17
Pl ai n
8½x11
Pl ai n11x8½
Pl ai n MP  tr a y
Pl ai n APSAuto  %
Re d u ce 100%
Exposur e Auto
Stapl e Stapl e
Left Top Stapl e Off100%
/Enl ar ge ModeExposur e
/Punch
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Operation
3-3
NOTE: You can adjust the angle of the operation panel 
as shown by releasing the operation panel lock lever. 
After adjustment, lock the lever again. 
When adjusting the angle of the operation panel, do 
not place your hands or fingers underneath the 
operation panel. This can result in injury.
6Remove the finished copies from the output tray.
The output tray can hold up to 250 sheets of standard 
paper (80 g/m²). However, the capacity will vary 
depending on the type and condition of the paper.
When turning off the main power switch, press the 
Power key on the operation panel to off ({). Make 
sure that the Power lamp is off before turning off the 
main power switch. Turning off the main power switch 
before pressing the Power key to off may cause 
damage to the equipped hard disk.
Caution
If the copier will not be used for a short period 
of time (overnight, etc.), turn the main power 
switch off ({ position). If it will not be used for 
an extended period of time (vacations, etc.), 
remove the power plug from the outlet for 
safety purposes.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Operation
3-4
Selecting Image Quality
Choose the image quality suited to the type of original.
1Place the originals in the document processor or on the platen.
2Press [Function].
3Press [Orig.Image Quality] ([Image 
Quality]).
4Select the image quality.
5Press the Start key to start copying.
NOTE: You can also adjust the exposure for each 
Image Quality mode. Refer to Chapter 3 of the 
Advanced Operation Guide. Image Quality Mode Description
Text+Photo For originals with both text and photographs.
Photo For originals primarily consisting of photographs.
Text For originals primarily consisting of text.
Ready to copy.11x8½Paper  Si ze
Progr am Functi on User choice
Ba si c 11x8½
Pl ai n
11x8½
Re cy cl e d
11x17
Pl ai n
8½x11
Pl ai n11x8½
Pl ai n MP  tr a y
Pl ai n APSAuto  %
Re d u ce 100%
Exposur e Auto
Stapl e Stapl e
Left Top Stapl e Off100%
/Enl ar ge ModeExposur e
/Punch
Ready to copy.11x8½Paper  Si ze
Progr am
Functi on User choice Ba si c Exposur e Reduce
Cov e r
Bookl etUp Ba tch
Scanning Auto
Selection
Bor de r Sel ect
Or i g.I mage2 sided/
Ma r g i n /
Ce nte r i ng
Sor t/
OffsetSelect
Orig.Size
Page #Combi ne
Form
Ov er l ayDown100%
Paper Separation
Mode /Enl ar ge
Er ase Mode Qual i ty
Ready to copy.
Or i g.I mage  Qual i ty
Te xt+Photo
Te xt PhotoBa ck Paper  Si ze
11x8
½
Te xt+P ho to :Se t thi s mo de  to  co py  o           wi th mi xe d text and photo.
Photo: For  copy i ng photo and pi ctuText: For  copy i ng text pages100%
Shor tcut
Downloaded From ManualsPrinter.com Manuals