Kyocera KM 8030 User Manual

							Preparing to Copy
2-5
5Insert the appropriate paper size card in the slot to 
indicate the size of the paper inside.
6Gently push the cassette back in.
Loading Paper in the MP Tray
The MP tray supports special paper (45 to 200 g/m²) in addition to standard and recycled paper. Up 
to 100 sheets of standard paper (80 g/m²) may be loaded in the MP tray. 
The MP tray accepts paper sizes from 5 
1/2×8 1/2 to 11 × 17 and from 16K, 8K, Folio, A6R, and 
B6R to A3.
The capacity of the MP tray is as follows.
IMPORTANT: After loading paper, be sure to specify the type and size of the paper loaded in the 
MP tray on the operation panel. For further details, refer to Specifying the Paper Size to the MP Tray 
on page2-11 and Specifying the Paper Type to the MP Tray on page2-14.
1Open the MP tray.
For paper larger than 8
1/2× 11 or A4R, pull out the 
MP tray extension.
Paper Type Capacity
Standard paper (80 g/m²) 100 sheets
Standard paper (120 g/m², 160 g/m², 200 g/m²) or 
transparencies25 sheets
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-6
2Adjust the paper width guides to fit the width of the 
paper.
3Insert the paper along the paper width guides into the 
tray until it stops.
Ensure that the paper width guides are flush against 
the edges of the paper.
IMPORTANT: Before loading postcards and other 
types of thick paper that may be curled, straighten out 
the paper. The paper may not be fed depending on the 
paper quality.
Only load the MP tray when you are using. Avoid 
leaving paper in the MP tray.
Ensure that the loaded paper does not exceed the 
level indicated. Exceeding the maximum level may 
cause paper jam.
When loading envelopes, open the flap and keep the 
printing side face-up. Insert envelopes against the  guide with the flap on the right until they stop. 
Loading Paper in the Optional Side Feeder
The optional side feeder has a capacity of 4,000 sheets of 11 × 81/2 (A4 or B5) standard paper 
(80 g/m²).
IMPORTANT:  After loading paper, be sure to specify th e type and size of the paper loaded in the 
side feeder on the operation panel. Refer to  Specifying the Paper Type on page2-9 for details.
1Press the switch for the paper lifter on the right side of 
the side feeder. The paper lifter inside of the side 
feeder will drop to the bottom.
NOTE:  When the side feeder runs out of paper, the 
paper lifter will automatically descend to the bottom.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy2-7
2Open the right cover.
NOTE: When the right cover is open, the paper lifter 
will not descend if you press the switch for the paper 
lifter.
It is easier to load new paper with the top cover open.
3Align the paper flush against the left side in the back of 
the feeder as you load it.
IMPORTANT:  Before loading the paper, be sure that it 
is not curled or folded. Paper that is curled or folded 
may cause paper jams.
Ensure that the loaded paper does not exceed the 
level indicated. Exceedi ng the maximum level may 
cause paper jam.
4Close the top and right covers of the side feeder.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-8
Specifying Paper Type and Size to the Cassettes and MP Tray
After loading paper in the cassettes 1 or 2 or the optional side feeder (cassette 5), specify the paper 
type. Refer to Specifying the Paper Type on page2-9 for details.
After loading paper in the cassettes 3 or 4, specify both the paper type and size. Refer to Specifying 
the Paper Size below and Specifying the Paper Type on page2-9.
After loading paper in the MP tray, specify both the paper type and size. Refer to Specifying the 
Paper Size to the MP Tray on page2-11 and Specifying the Paper Type to the MP Tray on 
page2-14.
Specifying the Paper Size
Specify the paper size when using the cassettes 3 and 4. For automatic detection of the paper size, 
specify [Auto Detection] and select [Centimeter] or [Inch] as the unit. 
The following paper sizes are available.
11 × 17, 8 
1/2×14, 11×8 1/2, 8 1/2×11, 5 1/2×8 1/2, 8 1/2×13 1/2, 8 1/2× 13 (Oficio 2), A3, B4, 
A4, A4R, B5, B5R, A5R, Folio, 8K and 16K
1Press the System Menu/Counter key.
2Press [Machine Default].
3Use the numeric keys to enter the 
four-digit management code. By default, 
the management code is 6000 for 60 
cpm model and 8000 for 80 cpm model.
NOTE: When installing the optional 
security kit, enter the eight-digit 
management code. By default, the 
management code is 60006000 for 60 
cpm model and 80008000 for 80 cpm 
model.
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pri nt L anguage
MP  tr a y
Or i g. Si ze Re g i s te r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAccounti ng
Enter the adminis trator number.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-9
4Press [S] or [T] to choose Paper size 
[3rd drawer] (Paper size [3rd cassette]) 
or Paper size [4th drawer] (Paper size 
[4th cassette]). Press [Change #] to 
begin changing settings.
5When [Auto Detection] is selected, 
choose the unit of measurement. When 
[Standard sizes] is selected, choose the 
paper size. 
Press [Close].
[Close]: Returns to the previous page by 
holding the settings.
[Back]: Returns to the previous page by 
canceling the settings.
6Press [Close].
7Press [End]. The touch panel will return to the [Basic] screen.
Specifying the Paper Type
Specify the paper type when using the cassettes 1 to 5. 
The following paper types are available. 
Plain, Recycled, Preprinted, Bond, Color (Colour), Letterhead, Thick paper, High Quality and 
Custom 1-8
1Press the System Menu/Counter key.
2Press [Machine Default].
Sy stem Menu
System Menu / Counter
Auto drawer switching
Paper size (3rd drawer)
Paper  si ze (4th dr awer )
Paper  ty pe (1st dr awer )
Paper  ty pe (2nd dr awer ) Change #Defaul t menu
On / Al l  ty pes of paper
11x17
Auto / I nch
Pl ai n
Re cy cl e dSe tti ng  mo d e Ma ch i n e  D e f a u l t
Auto
A5B5
B5 A4
Standar dA3 B4
A4
Folio Paper size (3rd drawer)
Sel ect paper  si ze.
S y s te m  Me n u Ma ch i n e  D e f a u l t- Detecti on
si ze s
Cl o se
5½ x 8 ½ 
8½ x 1 3 ½ 
8½ x 1 3 
8KBa ck
16K
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pr i nt Language
MP  tr a y
Or i g. Si ze Re g i ste r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAcco u nti ng
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-10
3Use the numeric keys to enter the 
four-digit management code. By default, 
the management code is 6000 for 60 
cpm model and 8000 for 80 cpm model.
4Press [S] or [T] to choose from Paper 
type (1st drawer) (Paper type [1st 
cassette]) through Paper type (5th 
drawer) (Paper type [5th cassette]). 
Press [Change #] to begin changing 
settings.
NOTE: Paper type (5th drawer) (Paper 
type [5th cassette]) is displayed when 
installing the optional side feeder.
5Select the paper type and press [Close].
6Press [Close].
7Press [End]. The touch panel will return to the [Basic] screen.
Enter the adminis trator number.
System Menu / Counter
Sy stem MenuMa ch i n e  D e fa u l t
Paper  si ze (4th dr awer )
Paper  ty pe (1st dr awer )Defaul t menu Setti ng mode
Auto / I nch
Paper  ty pe (2nd dr awer )
Paper  ty pe (3r d dr awer )
Paper  ty pe (4th dr awer )Pl ai n
Re cy cl e d
Pl ai n
Pl ai n
Cha nge  #
Paper  ty pe (1st dr awer )
Cu sto m 
Cu sto m  Cu sto m 
Cu sto m 
Ma ch i n e  D e f a u l t Sy stem MenuBondCo l o r Re cy cl e d Pl ai n
Preprinted
LetterheadThi ck
HighCu sto m 1
Cu sto m 2
Cu sto m 3
Cu sto m 4Ba ck
Sel ect and di spl ay  paper  ty pe.
-paper
Qual i ty
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-11
Specifying the Paper Size to the MP Tray
Specify the paper size when using the MP tray. 
Select the paper size from the followings. 
Auto Detect
The paper size is automatically detected. Specify [Centimeter] or [Inch].
1Press the System Menu/Counter key.
2Press [MP tray Setting].
3Press [Auto Detection].
4Press [Centimeter] or [Inch].
5Press [Close]. The touch panel will return to the [Basic] screen. Setting Method Unit Paper Sizes
Auto Detect Inch 11 × 17, 8 
1/2×14, 11×81/2, 81/2× 11 and 51/2×81/2
Centimeter A3, B4, A4, A4R, B5, B5R, A5R, B6R, A6R and Folio
Other Standard Sizes ISO B5, Envelope DL, Envelope C5, Envelope C4, Comm. 
#10, Comm. #9, Monarch, Executive, OUFUKU (Return 
postcard), YOUKEI 2, YOUKEI 4, 8
1/2×131/2, 81/2×13 
(Oficio 2), 8K and 16K
Input Size Inch models
Ve r t i c a l :  3
7/8 to 115/8 (in 1/8 increments) 
Horizontal: 5
7/8 to 17 (in 1/8 increments)
Metric models
Vertical: 98 to 297 mm (in 1-mm increments) 
Horizontal: 148 to 432 mm (in 1-mm increments)
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pr i nt Language
MP  tr a y
Or i g. Si ze Re g i ste r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAcco u nti ng
MP tr a y  Se tti ng
AutoBa ck
System Menu / Counter
Input size
Other s
Standar d Paper  Si ze Paper  Ty pe
Plain
Centimeter
Inch Unit
Detecti on
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-12
Other Standard Sizes
Specify special standard sizes.
1Press the System Menu/Counter key.
2Press [MP tray Setting].
3Press [Others Standard] and then 
[Select size].
4Select the paper size.
5Press [Close].
6Press [Close]. The touch panel will return to the [Basic] screen.
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pri nt L anguage
MP  tr a y
Or i g. Si ze Re g i s te r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAccounti ng
MP tr a y  Se tti ng
AutoBa ck
System Menu / Counter
Input size
Other s
Standar d Paper  Si ze Paper  Ty pe
Pl ai n
Ce nti me te r
Inch Unit
Detecti on
System Menu / Counter
Ba ck
C5 Env el ope Sel ect si ze
DL Env el ope
C4 Env el ope I SO B5 Comm.#10
Comm.#9
MOYOU KEI  2
EXOU F U KU
YOU KEI  48K
8½ x 1 3 ½ 8½x13
16K HAGAKI
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-13
Input Size
Specify the required paper size.
1Press the System Menu/Counter key.
2Press [MP tray Setting].
3Press [Input size].
4Press [+] or [-] to specify the vertical 
size. With the metric models, you may 
enter the size directly using the numeric 
keys by pressing [#-Keys].
The setting range is as follows.
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pr i nt Language
MP  tr a y
Or i g. Si ze Re g i ste r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAcco u nti ng
MP tr a y  Se tti ng
AutoBa ck
System Menu / Counter
Input size
Other s
Standar d Paper  Si ze Paper  Ty pe
Plain
Centimeter
Inch Unit
Detecti on
MP tr a y  Se tti ng
AutoBa ck
System Menu / Counter
Y
Input size
Other s
Standar dX Paper  Si ze Paper  Ty pe
Plain (3
7/8115/8)
315/16513/16 (5
7/817)
Detecti on
Setting Range
Inch models 3 
7/8 to 11 5/8 (in 1/8 increments)
Metric models 98 to 297 mm (in 1-mm increments)
Downloaded From ManualsPrinter.com Manuals 
						

							Preparing to Copy
2-14
5Press [+] or [-] to specify the horizontal 
size. With the metric models, you may 
enter the size directly using the numeric 
keys by pressing [#-Keys].
The setting range is as follows.
6Press [Close]. The touch panel will return to the [Basic] screen.
Specifying the Paper Type to the MP Tray
Specify the paper type when using the MP tray. 
The following paper types are available. 
Plain, Transparency, Rough, Vellum, Labels, Recycled, Preprinted, Bond, Cardstock, Color 
(Colour), Prepunched, Letterhead, Thick paper, Envelope, High Quality and Custom 1-8
1Press the System Menu/Counter key.
2Press [MP tray Setting].
3Press [Select Paper Type].
MP tr a y  Se tti ng
AutoBa ck
System Menu / Counter
Y
Input size
Other s
Standar dX Paper  Si ze Paper  Ty pe
Pl ai n (3
7/8115/8)
315/16513/16 (5
7/817)
Detecti on
Setting Range
Inch models 5 
7/8 to 17 (in 1/8 increments)
Metric models 148 to 432 mm (in 1-mm increments)
System Menu / Counter
Job Sy stem Menu
Management BOX
Re p o r t Pri nt L anguage
MP  tr a y
Or i g. Si ze Re g i s te r
Management Document
Defaul t Ma ch i n e Defaul t Co p y
Setti ngAccounti ng
Cl o se Ba ck
m Menu / Counter
Paper  Ty pe
PlainSel ect
Ce nti me te r
Inch Unit
Paper  Ty pe
Downloaded From ManualsPrinter.com Manuals